[PATCH 1/2] documentation: add rockchip spi documentation

[Mark Rutland]

On Tue, Jun 24, 2014 at 04:58:43AM +0100, addy ke wrote:
> Signed-off-by: addy ke <addy.ke at rock-chips.com>
> ---
>  .../devicetree/bindings/spi/spi-rockchip.txt       | 51 ++++++++++++++++++++++
>  1 file changed, 51 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/spi-rockchip.txt
> 
> diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
> new file mode 100644
> index 0000000..ce9c881
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
> @@ -0,0 +1,51 @@
> +* Rockchip SPI Controller
> +
> +The Rockchip SPI controller is used to interface with various devices such as flash
> +and display controllers using the SPI communication interface.
> +
> +Required SoC Specific Properties:
> +
> +- compatible: should be one of the following.
> +    - rockchip,rk3066-spi: for rk3066, rk3188 and rk3288 platforms.

Are you sure you don't want specifc strings for rk3188 and rk3288 (in
addtion to the common "rockchip,rk3066-spi")?

> +- reg: physical base address of the controller and length of memory mapped
> +       region.
> +- interrupts: The interrupt number to the cpu. The interrupt specifier format
> +              depends on the interrupt controller.
> +- clocks: Must contain an entry for each entry in clock-names.
> +- clock-names: Shall be "spiclk" for the transfer-clock, and "apb_pclk" for
> +			   the peripheral clock.
> +
> +Optional properties:
> +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
> +		Documentation/devicetree/bindings/dma/dma.txt
> +- dma-names: DMA request names should include "tx" and "rx" if present.
> +
> +Example:
> +
> +- SoC Specific Portion:
> +
> +	spi0: spi at ff110000 {
> +		compatible = "rockchip,rockchip-spi";

This does not match the description of the compatible property.

> +		reg = <0xff110000 0x1000>;
> +		dmas = <&pdma1 11>, <&pdma1 12>;
> +		dma-names = "tx", "rx";
> +		#address-cells = <1>;
> +		#size-cells = <0>;

These weren't mentioned.

> +		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0 &spi0_cs1>;

pinctrl was not mentioned.

> +		clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
> +		clock-names = "spiclk", "apb_pclk";
> +		status = "disabled";

Any reason for the status?

> +	};
> +
> +- Board Specific Portion:
> +
> +	&spi0 {
> +		status = "okay";
> +		spi_test at 00 {
> +			compatible = "rockchip,spi_test";

Huh?

Mark.