[PATCH v2 2/3] ata: Add Qualcomm ARM SoC AHCI SATA host controller driver

Bartlomiej Zolnierkiewicz b.zolnierkie at samsung.com
Tue Jun 17 05:25:21 PDT 2014


Hi,

On Friday, June 13, 2014 11:16:03 AM Kumar Gala wrote:
> Add support for the Qualcomm AHCI SATA controller that exists on several
> SoC and specifically the IPQ806x family of chips.  The IPQ806x SATA support
> requires the associated IPQ806x SATA PHY Driver to be enabled as well.
> 
> Signed-off-by: Kumar Gala <galak at codeaurora.org>
> ---
> v2:
> * Fixed MODULE_LICENSE to be GPL v2
> 
>  drivers/ata/Kconfig     | 10 ++++++
>  drivers/ata/Makefile    |  1 +
>  drivers/ata/ahci_qcom.c | 86 +++++++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 97 insertions(+)
>  create mode 100644 drivers/ata/ahci_qcom.c
> 
> diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
> index 7671dba..aa88648 100644
> --- a/drivers/ata/Kconfig
> +++ b/drivers/ata/Kconfig
> @@ -132,6 +132,16 @@ config AHCI_MVEBU
>  
>  	  If unsure, say N.
>  
> +config AHCI_QCOM
> +	tristate "Qualcomm AHCI SATA support"
> +	depends on ARCH_QCOM
> +	help
> +	  This option enables support for AHCI SATA controller
> +	  integrated into Qualcomm ARM SoC chipsets. For more
> +	  information please refer to http://www.qualcomm.com/chipsets.
> +
> +	  If unsure, say N.
> +
>  config AHCI_SUNXI
>  	tristate "Allwinner sunxi AHCI SATA support"
>  	depends on ARCH_SUNXI
> diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
> index 5a02aee..15401e9 100644
> --- a/drivers/ata/Makefile
> +++ b/drivers/ata/Makefile
> @@ -13,6 +13,7 @@ obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
>  obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
>  obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
>  obj-$(CONFIG_AHCI_MVEBU)	+= ahci_mvebu.o libahci.o libahci_platform.o
> +obj-$(CONFIG_AHCI_QCOM)		+= ahci_qcom.o libahci.o libahci_platform.o
>  obj-$(CONFIG_AHCI_SUNXI)	+= ahci_sunxi.o libahci.o libahci_platform.o
>  obj-$(CONFIG_AHCI_ST)		+= ahci_st.o libahci.o libahci_platform.o
>  obj-$(CONFIG_AHCI_XGENE)	+= ahci_xgene.o libahci.o libahci_platform.o
> diff --git a/drivers/ata/ahci_qcom.c b/drivers/ata/ahci_qcom.c
> new file mode 100644
> index 0000000..bfb7a77
> --- /dev/null
> +++ b/drivers/ata/ahci_qcom.c
> @@ -0,0 +1,86 @@
> +/*
> + * Qualcomm ARM SoC AHCI SATA platform driver
> + *
> + * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
> + *
> + * Copyright (c) 2014, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/pm.h>
> +#include <linux/device.h>
> +#include <linux/platform_device.h>
> +#include <linux/libata.h>
> +#include <linux/ahci_platform.h>
> +#include "ahci.h"
> +
> +static const struct ata_port_info qcom_ahci_port_info = {
> +	.flags		= AHCI_FLAG_COMMON,
> +	.pio_mask	= ATA_PIO4,
> +	.udma_mask	= ATA_UDMA6,
> +	.port_ops	= &ahci_platform_ops,
> +};
> +
> +static int qcom_ahci_probe(struct platform_device *pdev)
> +{
> +	struct ahci_host_priv *hpriv;
> +	struct clk *rxoob_clk;
> +	int rc;
> +
> +	hpriv = ahci_platform_get_resources(pdev);
> +	if (IS_ERR(hpriv))
> +		return PTR_ERR(hpriv);
> +
> +	/* Try and set the rxoob clk to 100Mhz */
> +	rxoob_clk = of_clk_get_by_name(pdev->dev.of_node, "rxoob");
> +	if (IS_ERR(rxoob_clk))
> +		return PTR_ERR(rxoob_clk);
> +
> +	rc = clk_set_rate(rxoob_clk, 100000000);

Shouldn't the clk_prepare_enable() be called first?

> +	if (rc)
> +		return rc;

of_clk_get_by_name() gets an extra reference on the clock so clk_put()
should be called on failure.

> +	rc = ahci_platform_enable_resources(hpriv);
> +	if (rc)
> +		return rc;
> +
> +	rc = ahci_platform_init_host(pdev, hpriv, &qcom_ahci_port_info, 0, 0);
> +	if (rc)
> +		goto disable_resources;
> +
> +	return 0;
> +disable_resources:
> +	ahci_platform_disable_resources(hpriv);
> +	return rc;
> +}
> +
> +static const struct of_device_id qcom_ahci_of_match[] = {
> +	{ .compatible = "qcom,msm-ahci", },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, qcom_ahci_of_match);
> +
> +static struct platform_driver qcom_ahci_driver = {
> +	.probe = qcom_ahci_probe,
> +	.remove = ata_platform_remove_one,
> +	.driver = {
> +		.name = "qcom_ahci_qcom",
> +		.owner = THIS_MODULE,
> +		.of_match_table = qcom_ahci_of_match,
> +	},

This driver lacks PM suspend/resume support.  I assume that
the IPQ806x platform also doesn't support suspend/resume yet
(if so a comment in the driver code about this would be useful),
otherwise the driver should be fixed.

> +};
> +module_platform_driver(qcom_ahci_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm AHCI SATA platform driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("ahci:qcom");

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics




More information about the linux-arm-kernel mailing list