[PATCH v2 2/6] input: touchscreen: imx25 tcq driver
Dmitry Torokhov
dmitry.torokhov at gmail.com
Sun Jun 15 00:27:40 PDT 2014
Hi Denis,
On Fri, Jun 13, 2014 at 05:21:35PM +0200, Denis Carikli wrote:
> +
> + if (ret == 0 && samples != 0) {
> + /*
> + * only if both touch measures are below a treshold,
> + * the position is valid
> + */
> + if (touch_pre < priv->pen_threshold &&
> + touch_post < priv->pen_threshold) {
> + /* valid samples, generate a report */
> + x_pos /= priv->sample_count;
> + y_pos /= priv->sample_count;
> + input_report_abs(priv->idev, ABS_X, x_pos);
> + input_report_abs(priv->idev, ABS_Y, y_pos);
> + input_report_key(priv->idev, BTN_TOUCH,
> + 0xfff - ((touch_pre + touch_post) / 2));
I still do not understand this calculation. input_report_key()
converts the last argument to a boolean, so the only time it would
report BTN_TOUCH UP here if (touch_pre + touch_post) / 2 is exactly
0xfff. Given that default threshold is 500 this won't ever happen.
Why isn't it simply:
input_report_key(priv->idev, BTN_TOUCH, 1);
?
...
> +
> +static irqreturn_t mx25_tcq_irq_thread(int irq, void *dev_id)
> +{
> + struct mx25_tcq_priv *priv = (struct mx25_tcq_priv *) dev_id;
No need to cast.
> + u32 sample_buf[TSC_MAX_SAMPLES];
> + int samples = 0;
> +
> + /* read all samples */
> + while (1) {
> + u32 stats;
> +
> + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> + if (stats & MX25_ADCQ_SR_EMPT)
> + break;
> +
> + if (samples < TSC_MAX_SAMPLES) {
> + regmap_read(priv->regs, MX25_ADCQ_FIFO,
> + &sample_buf[samples]);
> + ++samples;
> + } else {
> + u32 discarded;
> + /* discard samples */
> + regmap_read(priv->regs, MX25_ADCQ_FIFO, &discarded);
> + }
> + }
> +
> + mx25_tcq_create_event_for_4wire(priv, sample_buf, samples);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t mx25_tcq_irq(int irq, void *dev_id)
> +{
> + struct mx25_tcq_priv *priv = (struct mx25_tcq_priv *)dev_id;
Same here.
> + u32 stat;
> + int ret = IRQ_HANDLED;
> +
> + regmap_read(priv->regs, MX25_ADCQ_SR, &stat);
> +
> + if (stat & (MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR))
> + mx25_tcq_fifo_reset(priv);
> +
> + if (stat & MX25_ADCQ_SR_PD) {
> + mx25_tcq_disable_touch_irq(priv);
> + mx25_tcq_force_queue_start(priv);
> + mx25_tcq_enable_fifo_irq(priv);
> + }
> +
> + if (stat & MX25_ADCQ_SR_FDRY) {
> + mx25_tcq_disable_fifo_irq(priv);
> + ret = IRQ_WAKE_THREAD;
> + }
> +
> + regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD |
> + MX25_ADCQ_SR_EOQ,
> + MX25_ADCQ_SR_FRR |
> + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD |
> + MX25_ADCQ_SR_EOQ);
> +
> + return ret;
> +}
> +
> +/* configure the statemachine for a 4-wire touchscreen */
> +static int mx25_tcq_init(struct mx25_tcq_priv *priv)
> +{
> + u32 tgcr;
> + unsigned int ipg_div;
> + unsigned int adc_period;
> + unsigned int debounce_cnt;
> + unsigned int settling_time;
> + int itemct;
> + int ret;
> +
> + regmap_read(priv->core_regs, MX25_TSC_TGCR, &tgcr);
> + ipg_div = max_t(unsigned int, 4, MX25_TGCR_GET_ADCCLK(tgcr));
> + adc_period = clk_get_rate(priv->clk) / (ipg_div * 2 + 2);
> + debounce_cnt = DIV_ROUND_UP(priv->pen_debounce, adc_period * 8) - 1;
> + settling_time = DIV_ROUND_UP(priv->settling_time, adc_period);
> +
> +
> + /* Reset */
> + regmap_write(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QRST |
> + MX25_ADCQ_CR_FRST);
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QRST |
> + MX25_ADCQ_CR_FRST, 0);
> +
> + /* up to 128 * 8 ADC clocks are possible */
> + if (debounce_cnt > 127)
> + debounce_cnt = 127;
> +
> + ret = imx25_setup_queue_4wire(priv, 0x0, &itemct);
> + if (ret)
> + return ret;
> +
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_LITEMID_MASK |
> + MX25_ADCQ_CR_WMRK_MASK,
> + MX25_ADCQ_CR_LITEMID(itemct - 1) |
> + MX25_ADCQ_CR_WMRK(priv->expected_samples - 1));
> +
> + /* setup debounce count */
> + regmap_update_bits(priv->core_regs, MX25_TSC_TGCR,
> + MX25_TGCR_PDBTIME_MASK,
> + MX25_TGCR_PDBTIME(debounce_cnt));
> +
> + /* enable debounce */
> + regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDBEN,
> + MX25_TGCR_PDBEN);
> + regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDEN,
> + MX25_TGCR_PDEN);
> +
> + /* enable the engine on demand */
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QSM_FQS,
> + MX25_ADCQ_CR_QSM_FQS);
> +
> + mx25_tcq_re_enable_touch_detection(priv);
> +
> + return 0;
> +}
> +
> +static int mx25_tcq_parse_dt(struct platform_device *pdev,
> + struct mx25_tcq_priv *priv)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + u32 wires;
> + int ret;
> +
> + /* Setup defaults */
> + priv->pen_threshold = 500;
> + priv->sample_count = 3;
> + priv->pen_debounce = 1000000;
> + priv->settling_time = 250000;
> +
> + ret = of_property_read_u32(np, "fsl,wires", &wires);
> + if (ret) {
> + dev_err(&pdev->dev, "Failed to find fsl,wires properties\n");
> + return ret;
> + }
> +
> + if (wires == 4) {
> + priv->mode = MX25_TS_4WIRE;
> + } else {
> + dev_err(&pdev->dev, "%u-wire mode not supported\n", wires);
> + return -EINVAL;
> + }
> +
> + /* These are optional, we don't care about the return values */
> + of_property_read_u32(np, "fsl,pen-threshold", &priv->pen_threshold);
> + of_property_read_u32(np, "fsl,settling-time", &priv->settling_time);
> + of_property_read_u32(np, "fsl,pen-debounce", &priv->pen_debounce);
> +
> + return 0;
> +}
> +
> +static int mx25_tcq_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct input_dev *idev;
> + struct mx25_tcq_priv *priv;
> + struct resource *res;
> + void __iomem *mem;
> + int ret;
> + int irq;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + mem = devm_ioremap_resource(dev, res);
> + if (!mem)
> + return -ENOMEM;
> +
> + ret = mx25_tcq_parse_dt(pdev, priv);
> + if (ret)
> + return ret;
> +
> + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_tcq_regconfig);
> + if (IS_ERR(priv->regs)) {
> + dev_err(dev, "Failed to initialize regmap\n");
> + return PTR_ERR(priv->regs);
> + }
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq <= 0) {
> + dev_err(dev, "Failed to get IRQ\n");
> + return irq;
> + }
> +
> + idev = devm_input_allocate_device(dev);
> + if (!idev) {
> + dev_err(dev, "Failed to allocate input device\n");
> + return -ENOMEM;
> + }
> +
> + idev->name = mx25_tcq_name;
> + idev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
> + idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
> + input_set_abs_params(idev, ABS_X, 0, 0xfff, 0, 0);
> + input_set_abs_params(idev, ABS_Y, 0, 0xfff, 0, 0);
> +
> + idev->id.bustype = BUS_HOST;
> +
> + ret = input_register_device(idev);
> + if (ret) {
> + dev_err(dev, "Failed to register input device\n");
> + return ret;
> + }
> +
> + priv->idev = idev;
> +
> + priv->core_regs = mx25_tsadc_get_regmap(pdev->dev.parent);
> + priv->clk = mx25_tsadc_get_ipg(pdev->dev.parent);
> +
> + ret = clk_prepare_enable(priv->clk);
> + if (ret) {
> + dev_err(dev, "Failed to enable ipg clock\n");
> + return ret;
> + }
> +
> + ret = devm_request_threaded_irq(dev, irq, mx25_tcq_irq,
> + mx25_tcq_irq_thread, IRQF_ONESHOT, pdev->name, priv);
> + if (ret) {
> + dev_err(dev, "Failed requesting IRQ\n");
You are leaving clock enabled here.
> + return ret;
> + }
> +
> + ret = mx25_tcq_init(priv);
> + if (ret) {
> + dev_err(dev, "Failed to init tcq\n");
> + goto error_tcq_init;
> + }
> +
> + platform_set_drvdata(pdev, priv);
> +
> + return 0;
> +
> +error_tcq_init:
> + clk_disable_unprepare(priv->clk);
> + return ret;
> +}
> +
> +static int mx25_tcq_remove(struct platform_device *pdev)
> +{
> + struct mx25_tcq_priv *priv = platform_get_drvdata(pdev);
> +
> + clk_disable_unprepare(priv->clk);
> +
> + return 0;
> +}
> +
> +static struct platform_driver mx25_tcq_driver = {
> + .driver = {
> + .name = "mx25-tcq",
> + .owner = THIS_MODULE,
> + .of_match_table = mx25_tcq_ids,
> + },
> + .probe = mx25_tcq_probe,
> + .remove = mx25_tcq_remove,
> +};
> +module_platform_driver(mx25_tcq_driver);
> +
> +MODULE_DESCRIPTION("TS input driver for Freescale mx25");
> +MODULE_AUTHOR("Markus Pargmann <mpa at pengutronix.de>");
> +MODULE_LICENSE("GPL v2");
> --
> 1.7.9.5
>
Thanks.
--
Dmitry
More information about the linux-arm-kernel
mailing list