[PATCH] [media] staging: allow omap4iss to be modular

[Laurent Pinchart]

Hi Tony,

On Friday 13 June 2014 00:53:25 Tony Lindgren wrote:
> * Laurent Pinchart <laurent.pinchart at ideasonboard.com> [140612 23:48]:
> > On Thursday 12 June 2014 22:30:44 Tony Lindgren wrote:
> > > 1. They live in separate hardware modules that can be clocked separately
> > 
> > Actually I don't think that's true. The CSI2 PHY is part of the camera
> > device, with all its registers but the one above in the camera device
> > register space. For some weird reason a couple of bits were pushed to the
> > control module, but that doesn't make the CSI2 PHY itself a separate
> > device.
> 
> Yes they are separate. Anything in the system control module is
> a separate hardware module from the other devices. So in this case
> the CSI2 PHY is part of the system control module, not the camera
> module.

Section 8.2.3 ("ISS CSI2 PHY") of the OMAP4460 TRM (revision AA) documents the 
CSI2 PHY is being part of the ISS, with three PHY registers in the ISS 
register space (not counting the PHY interrupt and status bits in several 
other ISS registers) and one register in the system control module register 
space. It's far from clear which power domain(s) is (are) involved.

> > > 2. Doing a read-back to flush a posted write in one hardware module most
> > >    likely won't flush the write to other and that can lead into hard to
> > >    find mysterious bugs
> > 
> > The OMAP4 ISS driver can just read back the CAMERA_RX register, can't it ?
> 
> Right, but you would have to do readbacks both from the phy register and
> camera register to ensure writes get written. It's best to keep the
> logic completely separate especially considering that they can be
> clocked separately.
> 
> > > 3. If we ever have a common system control module driver, we need to
> > >    rewrite all the system control module register tinkering in the
> > >    drivers
> > 
> > Sure, but that's already the case today, as the OMAP4 ISS driver already
> > accesses the control module register directly. I won't make that worse :-)
> 
> Well it's in staging for a reason :)
> 
> > > So it's best to try to use an existing framework for it. That avoids
> > > tons of pain later on ;)
> > 
> > I agree, but I don't think the PHY framework would be the right
> > abstraction. As explained above the CSI2 PHY is part of the OMAP4 ISS, so
> > modeling its single control module register as a PHY would be a hack.
> 
> Well that register belongs to the system control module, not the
> camera module. It's not like the camera IO space is out of registers
> or something! :)

The PHY has 3 registers in the ISS I/O space and one register in the control 
module I/O space. I have no idea why they've split it that way. The clock 
enable bits are especially "interested", the source clock (CAM_PHY_CTRL_FCLK) 
comes from the ISS as documented in section 8.1.1 ("ISS Integration"), is 
gated by the control module (the gated clock is called CTRLCLK) and then goes 
back to the ISS CSI2 PHY (it's mentioned in the CSI2 PHY "REGISTER1" 
documentation).

> We're already handling similar control module phy cases, see for
> example drivers/phy/phy-omap-control.c. Maybe you have most of the
> code already there?

I'm afraid not. For PHYs that are in the system control module that solution 
is perfectly fine, but the CSI2 PHY isn't (or at least not all of it).

I would be fine with writing a separate PHY driver if the PHY was completely 
separate. As the documentation doesn't make it clear which part of the 
hardware belongs to which module, matching the software implementation with an 
unknown hardware implementation would be pretty difficult :-)

If you have a couple of minutes to spare and can look at the CSI2 PHY 
documentation in the TRM, you might be more successful than me figuring out 
how the hardware is implemented.

-- 
Regards,

Laurent Pinchart