OMAP baseline test results for v3.15-rc8
Dmitry Lifshitz
lifshitz at compulab.co.il
Mon Jun 2 01:45:47 PDT 2014
Hi Paul,
CM-T3517 is a bare-bone CoM without MMC/SD card slot (NAND option).
MMC/SD card interface (and some other peripherals) are properties of the
carrier base board SB-T35, which turns this CoM into fully functional
board SBC-T3517.
Please, use omap3-sbc-t3517.dtb target.
Attached Linux v3.15-rc8 boot log using omap2plus_defconfig.
On 06/02/2014 10:50 AM, Paul Walmsley wrote:
>
> Boot to userspace:
> FAIL ( 2/13): 2430sdp, cmt3517
> skip ( 2/13): 5912osk, 4460varsomom
> Pass ( 9/13): 2420n800, 3517evm, 3530es3beagle, 3730beaglexm,
> 37xxevm, 4430es2panda, 4460pandaes, am335xbone,
> am335xbonelt
>
>
Regards,
Dmitry
-------------- next part --------------
U-Boot 2009.11-cm-t3517-1 (Dec 10 2010 - 23:25:02)
AM35xx-GP ES2.0, L3-165MHz
CM-T3517 Module + LPDDR/NAND 128/512M
I2C: ready
DRAM: 256 MB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
PCB: 1.2
Die ID #7a64000100000000016b29c60d00c020
Net: DaVinci EMAC, smc911x-0
Hit any key to stop autoboot: 0
CM-T3517 # sete bootargs 'console=ttyO2,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p2 rootwait init=/bin/sh nohlt'
CM-T3517 # sete bootcmd 'tftp 0x82000000 uImage-cm-t3517_wdt.bin && bootm 0x82000000'
CM-T3517 # boot
Using DaVinci EMAC device
TFTP from server 192.168.11.10; our IP address is 192.168.6.204
Filename 'uImage-cm-t3517_wdt.bin'.
Load address: 0x82000000
Loading: #################################################################
#################################################################
################################################T #################
#################################################################
#################################################################
##########################################T #######################
#################################################################
######T ###########################################################
###################################T ##############################
################################################################T #
#################################################################
#############################T ####################################
##########################################################T #######
#################################################################
######################
done
Bytes transferred = 4769379 (48c663 hex)
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4769315 Bytes = 4.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.15.0-rc8 (lifshitz at compulab.co.il) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-70) ) #4 SMP Mon Jun 2 11:19:33 IDT 2014
[ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine model: CompuLab SBC-T3517 with CM-T3517
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] cma: CMA: reserved 16 MiB at 8e800000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] On node 0 totalpages: 65280
[ 0.000000] free_area_init_node: node 0, pgdat c092e8c0, node_mem_map cfcf2000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65280 pages, LIFO batch:15
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM3517 ES1.1 (l2cache sgx neon )
[ 0.000000] PERCPU: Embedded 9 pages/cpu @cfcaf000 s14080 r8192 d14592 u36864
[ 0.000000] pcpu-alloc: s14080 r8192 d14592 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768
[ 0.000000] Kernel command line: console=ttyO2,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p2 rootwait init=/bin/sh nohlt
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 227188K/261120K available (6111K kernel code, 664K rwdata, 2216K rodata, 393K init, 5522K bss, 33932K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0829e10 (8328 kB)
[ 0.000000] .init : 0xc082a000 - 0xc088c700 ( 394 kB)
[ 0.000000] .data : 0xc088e000 - 0xc09340c0 ( 665 kB)
[ 0.000000] .bss : 0xc09340c0 - 0xc0e98c48 (5523 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[ 0.000000] OMAP clockevent source: timer2 at 13000000 Hz
[ 0.000033] sched_clock: 32 bits at 13MHz, resolution 76ns, wraps every 330382100403ns
[ 0.000144] OMAP clocksource: timer1 at 13000000 Hz
[ 0.001575] Console: colour dummy device 80x30
[ 0.001674] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.001693] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.001708] ... MAX_LOCK_DEPTH: 48
[ 0.001722] ... MAX_LOCKDEP_KEYS: 8191
[ 0.001736] ... CLASSHASH_SIZE: 4096
[ 0.001750] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.001764] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.001777] ... CHAINHASH_SIZE: 16384
[ 0.001792] memory used by lock dependency info: 3695 kB
[ 0.001806] per task-struct memory footprint: 1152 bytes
[ 0.001885] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696)
[ 0.106203] pid_max: default: 32768 minimum: 301
[ 0.106962] Security Framework initialized
[ 0.107205] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.107234] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.111655] CPU: Testing write buffer coherency: ok
[ 0.113814] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.113955] Setting up static identity map for 0x805c88c8 - 0x805c8938
[ 0.120143] Brought up 1 CPUs
[ 0.120176] SMP: Total of 1 processors activated.
[ 0.120194] CPU: All CPU(s) started in SVC mode.
[ 0.125353] devtmpfs: initialized
[ 0.139166] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[ 0.213542] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp
[ 0.215672] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp
[ 0.294681] omap_hwmod: uart4: cannot be enabled for reset (3)
[ 0.314698] pinctrl core: initialized pinctrl subsystem
[ 0.319801] regulator-dummy: no parameters
[ 0.418889] NET: Registered protocol family 16
[ 0.429888] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.434387] In-band Error seen by USB_OTG at address 0
[ 0.434417] ------------[ cut here ]------------
[ 0.434469] WARNING: CPU: 0 PID: 1 at /home/lifshitz/workroot/git-repo/linux-cm-t3x/drivers/bus/omap_l3_smx.c:162 omap3_l3_app_irq+0x100/0x128()
[ 0.434487] Modules linked in:
[ 0.434524] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc8 #4
[ 0.434586] [<c001590c>] (unwind_backtrace) from [<c0012618>] (show_stack+0x10/0x14)
[ 0.434625] [<c0012618>] (show_stack) from [<c05b9744>] (dump_stack+0x78/0x94)
[ 0.434661] [<c05b9744>] (dump_stack) from [<c004323c>] (warn_slowpath_common+0x6c/0x8c)
[ 0.434691] [<c004323c>] (warn_slowpath_common) from [<c0043278>] (warn_slowpath_null+0x1c/0x24)
[ 0.434720] [<c0043278>] (warn_slowpath_null) from [<c0329ad4>] (omap3_l3_app_irq+0x100/0x128)
[ 0.434760] [<c0329ad4>] (omap3_l3_app_irq) from [<c0095ddc>] (handle_irq_event_percpu+0x58/0x20c)
[ 0.434789] [<c0095ddc>] (handle_irq_event_percpu) from [<c0095fcc>] (handle_irq_event+0x3c/0x5c)
[ 0.434821] [<c0095fcc>] (handle_irq_event) from [<c0098838>] (handle_level_irq+0xac/0x148)
[ 0.434849] [<c0098838>] (handle_level_irq) from [<c00956a8>] (generic_handle_irq+0x20/0x30)
[ 0.434879] [<c00956a8>] (generic_handle_irq) from [<c000f53c>] (handle_IRQ+0x4c/0xac)
[ 0.434906] [<c000f53c>] (handle_IRQ) from [<c0008600>] (omap3_intc_handle_irq+0x80/0x9c)
[ 0.434933] [<c0008600>] (omap3_intc_handle_irq) from [<c05c2ba4>] (__irq_svc+0x44/0x5c)
[ 0.434953] Exception stack(0xce055d68 to 0xce055db0)
[ 0.434978] 5d60: 00030b84 ce053070 00000000 ce052b00 60000153 ce005454
[ 0.435002] 5d80: ce005454 00000021 0000001a ce005434 60000153 00000000 00000000 ce055db0
[ 0.435021] 5da0: 00030b85 c05c25a0 20000153 ffffffff
[ 0.435058] [<c05c2ba4>] (__irq_svc) from [<c05c25a0>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 0.435089] [<c05c25a0>] (_raw_spin_unlock_irqrestore) from [<c0097670>] (__setup_irq+0x2d8/0x4c0)
[ 0.435118] [<c0097670>] (__setup_irq) from [<c0097910>] (request_threaded_irq+0xb8/0x13c)
[ 0.435154] [<c0097910>] (request_threaded_irq) from [<c085d88c>] (omap3_l3_probe+0x10c/0x16c)
[ 0.435195] [<c085d88c>] (omap3_l3_probe) from [<c0397fd4>] (platform_drv_probe+0x18/0x48)
[ 0.435225] [<c0397fd4>] (platform_drv_probe) from [<c03962c0>] (really_probe+0x78/0x218)
[ 0.435254] [<c03962c0>] (really_probe) from [<c0396574>] (driver_probe_device+0x30/0x48)
[ 0.435280] [<c0396574>] (driver_probe_device) from [<c0396620>] (__driver_attach+0x94/0x98)
[ 0.435306] [<c0396620>] (__driver_attach) from [<c0394ca4>] (bus_for_each_dev+0x54/0x88)
[ 0.435332] [<c0394ca4>] (bus_for_each_dev) from [<c0395ba8>] (bus_add_driver+0xdc/0x1d4)
[ 0.435359] [<c0395ba8>] (bus_add_driver) from [<c0396c5c>] (driver_register+0x78/0xf4)
[ 0.435386] [<c0396c5c>] (driver_register) from [<c0397818>] (platform_driver_probe+0x20/0xa4)
[ 0.435415] [<c0397818>] (platform_driver_probe) from [<c00088b8>] (do_one_initcall+0x34/0x160)
[ 0.435449] [<c00088b8>] (do_one_initcall) from [<c082abd4>] (do_basic_setup+0x90/0xc8)
[ 0.435477] [<c082abd4>] (do_basic_setup) from [<c082ac80>] (kernel_init_freeable+0x74/0x110)
[ 0.435510] [<c082ac80>] (kernel_init_freeable) from [<c05aaae4>] (kernel_init+0x8/0xe4)
[ 0.435537] [<c05aaae4>] (kernel_init) from [<c000ec08>] (ret_from_fork+0x14/0x2c)
[ 0.435803] ---[ end trace 06d1ca61a08dd8b8 ]---
[ 0.448829] Reprogramming SDRC clock to 332000000 Hz
[ 0.453158] platform 480c5000.aes: Cannot lookup hwmod 'aes'
[ 0.464408] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[ 0.465960] OMAP GPIO hardware version 2.5
[ 0.468276] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[ 0.471524] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[ 0.474778] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[ 0.478038] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
[ 0.481191] gpiochip_add: registered GPIOs 160 to 191 on device: gpio
[ 0.496039] platform 480c3000.sham: Cannot lookup hwmod 'sham'
[ 0.497128] platform 480cb000.smartreflex: Cannot lookup hwmod 'smartreflex_core'
[ 0.509289] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[ 0.512135] platform 480ab000.usb_otg_hs: Cannot lookup hwmod 'usb_otg_hs'
[ 0.667512] No ATAGs?
[ 0.667564] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.672304] OMAP DMA hardware revision 4.0
[ 0.712718] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot
[ 0.712847] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5
[ 0.780155] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver
[ 0.781570] of_get_named_gpiod_flags: can't parse gpios property of node '/hsusb1_power_reg[0]'
[ 0.782713] hsusb1_vbus: 3300 mV
[ 0.783396] of_get_named_gpiod_flags: can't parse gpios property of node '/hsusb2_power_reg[0]'
[ 0.784100] hsusb2_vbus: 3300 mV
[ 0.784742] of_get_named_gpiod_flags: can't parse gpios property of node '/regulator-vmmc[0]'
[ 0.785406] vmmc: 3300 mV
[ 0.786167] reg-fixed-voltage wl12xx_vmmc2.8: could not find pctldev for node /ocp/pinmux at 48002a00/pinmux_wl12xx_wkup_pins, deferring probe
[ 0.786360] platform wl12xx_vmmc2.8: Driver reg-fixed-voltage requests probe deferral
[ 0.786604] of_get_named_gpiod_flags: can't parse gpios property of node '/wl12xx_vaux2[0]'
[ 0.787360] vwl1271_vaux2: 1800 mV
[ 0.787989] of_get_named_gpiod_flags: can't parse gpios property of node '/regulator-vddvario-sb-t35[0]'
[ 0.788641] vddvario: no parameters
[ 0.789171] of_get_named_gpiod_flags: can't parse gpios property of node '/regulator-vdd33a-sb-t35[0]'
[ 0.789808] vdd33a: no parameters
[ 0.796762] SCSI subsystem initialized
[ 0.798296] usbcore: registered new interface driver usbfs
[ 0.798632] usbcore: registered new interface driver hub
[ 0.799376] usbcore: registered new device driver usb
[ 0.800027] usb_phy_gen_xceiv hsusb1_phy.5: could not find pctldev for node /ocp/pinmux at 48002030/pinmux_hsusb1_phy_reset_pins, deferring probe
[ 0.800097] platform hsusb1_phy.5: Driver usb_phy_gen_xceiv requests probe deferral
[ 0.800234] usb_phy_gen_xceiv hsusb2_phy.6: could not find pctldev for node /ocp/pinmux at 48002030/pinmux_hsusb2_phy_reset_pins, deferring probe
[ 0.800286] platform hsusb2_phy.6: Driver usb_phy_gen_xceiv requests probe deferral
[ 0.804125] omap_i2c 48070000.i2c: bus 0 rev3.3 at 400 kHz
[ 0.806475] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz
[ 0.808303] omap_i2c 48060000.i2c: bus 2 rev3.3 at 400 kHz
[ 0.816220] Switched to clocksource timer1
[ 1.114162] NET: Registered protocol family 2
[ 1.117580] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.117847] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
[ 1.119015] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.119376] TCP: reno registered
[ 1.119431] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 1.119760] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 1.121593] NET: Registered protocol family 1
[ 1.125013] RPC: Registered named UNIX socket transport module.
[ 1.125052] RPC: Registered udp transport module.
[ 1.125073] RPC: Registered tcp transport module.
[ 1.125091] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.127629] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 1.137137] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 1.378968] VFS: Disk quotas dquot_6.5.2
[ 1.379206] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.382752] NFS: Registering the id_resolver key type
[ 1.383492] Key type id_resolver registered
[ 1.383529] Key type id_legacy registered
[ 1.383737] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.384583] msgmni has been set to 475
[ 1.395561] io scheduler noop registered
[ 1.395603] io scheduler deadline registered
[ 1.395751] io scheduler cfq registered (default)
[ 1.401578] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568
[ 1.402477] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
[ 1.407239] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV
[ 1.409639] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.423830] omap_uart 4806a000.serial: no wakeirq for uart0
[ 1.423896] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial at 4806a000[0]'
[ 1.427808] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[ 1.431028] omap_uart 4806c000.serial: no wakeirq for uart0
[ 1.431087] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial at 4806c000[0]'
[ 1.432632] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[ 1.434973] omap_uart 49020000.serial: no wakeirq for uart0
[ 1.435029] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial at 49020000[0]'
[ 1.437090] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[ 2.756411] console [ttyO2] enabled
[ 2.815596] brd: module loaded
[ 2.849957] loop: module loaded
[ 2.858675] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 3.064914] libphy: smsc911x-mdio: probed
[ 3.146917] smsc911x 2d000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=2d000000.etherne:01, irq=-1)
[ 3.159520] smsc911x 2d000000.ethernet eth0: MAC Address: 36:94:5b:1b:64:70
[ 3.216032] davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
[ 3.222557] davinci_mdio davinci_mdio.0: detected phy mask fffffffc
[ 3.233324] libphy: davinci_mdio.0: probed
[ 3.237857] davinci_mdio davinci_mdio.0: phy[0]: device davinci_mdio.0:00, driver unknown
[ 3.246535] davinci_mdio davinci_mdio.0: phy[1]: device davinci_mdio.0:01, driver unknown
[ 3.256506] usbcore: registered new interface driver asix
[ 3.262425] usbcore: registered new interface driver ax88179_178a
[ 3.269147] usbcore: registered new interface driver cdc_ether
[ 3.275616] usbcore: registered new interface driver smsc95xx
[ 3.281954] usbcore: registered new interface driver net1080
[ 3.288192] usbcore: registered new interface driver cdc_subset
[ 3.294627] usbcore: registered new interface driver zaurus
[ 3.300910] usbcore: registered new interface driver cdc_ncm
[ 3.309776] usbcore: registered new interface driver cdc_wdm
[ 3.316300] usbcore: registered new interface driver usb-storage
[ 3.322942] usbcore: registered new interface driver usbtest
[ 3.332885] mousedev: PS/2 mouse device common for all mice
[ 3.344451] spi1.0 supply vcc not found, using dummy regulator
[ 3.353902] ads7846 spi1.0: touchscreen, irq 169
[ 3.361909] input: ADS7846 Touchscreen as /devices/68000000.ocp/48098000.spi/spi_master/spi1/spi1.0/input/input0
[ 3.383110] i2c /dev entries driver
[ 3.392899] Driver for 1-wire Dallas network protocol.
[ 3.407144] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 3.417626] of_get_named_gpiod_flags exited with status 0
[ 3.423356] of_get_named_gpiod_flags exited with status 0
[ 3.466861] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc at 480b4000[0]'
[ 3.476164] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc at 480b4000[0]'
[ 3.486326] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517
[ 3.494138] platform 480b4000.mmc: Driver omap_hsmmc requests probe deferral
[ 3.503138] usbcore: registered new interface driver usbhid
[ 3.509126] usbhid: USB HID core driver
[ 3.515226] oprofile: using arm/armv7
[ 3.520174] TCP: cubic registered
[ 3.523679] Initializing XFRM netlink socket
[ 3.528495] NET: Registered protocol family 17
[ 3.533298] NET: Registered protocol family 15
[ 3.538631] Key type dns_resolver registered
[ 3.545290] PM: no software I/O chain control; some wakeups may be lost
[ 3.552883] ThumbEE CPU extension supported.
[ 3.557542] Registering SWP/SWPB emulation handler
[ 3.576523] vwl1271_vaux2: disabling
[ 3.580320] vmmc: disabling
[ 3.583267] hsusb2_vbus: disabling
[ 3.587002] hsusb1_vbus: disabling
[ 3.593871] of_get_named_gpiod_flags exited with status 0
[ 3.601214] vw1271: 1800 mV
[ 3.605733] of_get_named_gpiod_flags exited with status 0
[ 3.613238] of_get_named_gpiod_flags exited with status 0
[ 3.620577] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc at 480b4000[0]'
[ 3.629852] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc at 480b4000[0]'
[ 3.741010] /home/lifshitz/workroot/git-repo/linux-cm-t3x/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 3.835073] Waiting for root device /dev/mmcblk0p2...
[ 3.847356] omap_hsmmc 480b4000.mmc: card claims to support voltages below defined range
[ 3.871505] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[ 3.881628] mmc1: new SDIO card at address 0001
[ 17.337245] mmc0: new SDHC card at address e624
[ 17.346375] mmcblk0: mmc0:e624 SU08G 7.40 GiB
[ 17.367618] mmcblk0: p1 p2
[ 17.482047] EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
[ 17.496648] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
[ 17.540713] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 17.549636] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 17.561280] devtmpfs: mounted
[ 17.565783] Freeing unused kernel memory: 392K (c082a000 - c088c000)
/bin/sh: can't access tty; job control turned off
# ls
bin dev home media opt root selinux sys usr
boot etc lib mnt proc sbin srv tmp var
#
More information about the linux-arm-kernel
mailing list