[PATCH v4 4/4] ARM: dts: Add exynos5250-spring device tree

Andreas Färber afaerber at suse.de
Thu Jul 31 09:08:29 PDT 2014


Adds initial support for the HP Chromebook 11.

Cc: Vincent Palatin <vpalatin at chromium.org>
Cc: Doug Anderson <dianders at chromium.org>
Cc: Stephan van Schaik <stephan at synkhronix.com>
Signed-off-by: Andreas Färber <afaerber at suse.de>
---
 v3 -> v4:
 * Fixed samsung,pin-function 1 -> 0 for dp-hpd-gpio
 * Replaced dp-hpd-gpio with existing dp_hpd, overriding it
 
 v2 -> v3:
 * Use GPIO_ACTIVE_{LOW,HIGH} (Doug Anderson)
 * Use symbolic KEY_POWER instead of comment
 * Moved hsic_reset to new USB3503 node's reset-gpios (Vincent Palatin)
 * Use dp_hpd_gpio for dp-controller (Doug Anderson, Ajay Kumar)
 * Override sd1_{clk,cmd,cd,bus4} pinctrl similar to Snow (Doug Anderson)
 * Added ec_irq pinctrl for cros_ec (Doug Anderson)
 * Reordered nodes to minimize diff against Snow (Doug Anderson)
 * Dropped obsolete mmc_2 override (Doug Anderson)
 * Added lid-switch node (Doug Anderson)
 * Added gpio-keys pinctrl (Doug Anderson)
 * Added bootargs to avoid empty /chosen node and to document console setting
 * Renamed s5m8767_pmic node to avoid underscore
 * Use new style for overriding inherited pinctrl nodes, too
 * Enable i2s0 node
 
 v1 -> v2:
 * Use label-based overriding/extension of nodes. (Doug Anderson)
 * Dropped tps65090 for now, until we know where to place it.
 * Dropped non-Spring nodes from -cros-common.dtsi rather than disabling them.
 * Enabled a missing MMC node for access to internal storage.
 * Dropped display-timings from dp-controller node. (Ajay Kumar)

 arch/arm/boot/dts/Makefile              |   1 +
 arch/arm/boot/dts/exynos5250-spring.dts | 539 ++++++++++++++++++++++++++++++++
 2 files changed, 540 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 80a781f76e88..dec4c292f63d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
+	exynos5250-spring.dtb \
 	exynos5260-xyref5260.dtb \
 	exynos5410-smdk5410.dtb \
 	exynos5420-arndale-octa.dtb \
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
new file mode 100644
index 000000000000..1fdfa04182fc
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@@ -0,0 +1,539 @@
+/*
+ * Google Spring board device tree source
+ *
+ * Copyright (c) 2013 Google, Inc
+ * Copyright (c) 2014 SUSE LINUX Products GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "exynos5250.dtsi"
+
+/ {
+	model = "Google Spring";
+	compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5";
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=tty1";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&power_key_irq>, <&lid_irq>;
+
+		power {
+			label = "Power";
+			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			gpio-key,wakeup;
+		};
+
+		lid-switch {
+			label = "Lid";
+			gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <5>; /* EV_SW */
+			linux,code = <0>; /* SW_LID */
+			debounce-interval = <1>;
+			gpio-key,wakeup;
+		};
+	};
+
+	usb3_vbus_reg: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "P5.0V_USB3CON";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpe1 0 GPIO_ACTIVE_LOW>;
+		enable-active-high;
+	};
+
+	usb at 12110000 {
+		samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	usb-hub {
+		compatible = "smsc,usb3503a";
+		reset-gpios = <&hsic_reset>;
+	};
+
+	fixed-rate-clocks {
+		xxti {
+			compatible = "samsung,clock-xxti";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	hdmi {
+		hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_hpd_irq>;
+		phy = <&hdmiphy>;
+		ddc = <&i2c_2>;
+		hdmi-en-supply = <&s5m_ldo8_reg>;
+		vdd-supply = <&s5m_ldo8_reg>;
+		vdd_osc-supply = <&s5m_ldo10_reg>;
+		vdd_pll-supply = <&s5m_ldo8_reg>;
+	};
+
+	fimd at 14400000 {
+		status = "okay";
+		samsung,invert-vclk;
+	};
+
+	dp-controller at 145B0000 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp_hpd>;
+		samsung,color-space = <0>;
+		samsung,dynamic-range = <0>;
+		samsung,ycbcr-coeff = <0>;
+		samsung,color-depth = <1>;
+		samsung,link-rate = <0x0a>;
+		samsung,lane-count = <1>;
+		samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&dp_hpd {
+	samsung,pins = "gpc3-0";
+	samsung,pin-function = <0>;
+	samsung,pin-pud = <3>;
+	samsung,pin-drv = <0>;
+};
+
+&i2c_0 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <378000>;
+
+	s5m8767-pmic at 66 {
+		compatible = "samsung,s5m8767-pmic";
+		reg = <0x66>;
+		interrupt-parent = <&gpx3>;
+		interrupts = <2 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
+		wakeup-source;
+
+		s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
+		                              <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
+		                              <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
+
+		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
+		                             <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
+		                             <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
+
+		/*
+		 * The following arrays of DVS voltages are not used, since we are
+		 * not using GPIOs to control PMIC bucks, but they must be defined
+		 * to please the driver.
+		 */
+		s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+		                                 <1250000>, <1200000>,
+		                                 <1150000>, <1100000>,
+		                                 <1000000>, <950000>;
+
+		s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+		                                 <1100000>, <1100000>,
+		                                 <1000000>, <1000000>,
+		                                 <1000000>, <1000000>;
+
+		s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+		                                 <1200000>, <1200000>,
+		                                 <1200000>, <1200000>,
+		                                 <1200000>, <1200000>;
+
+		clocks {
+			compatible = "samsung,s5m8767-clk";
+			#clock-cells = <1>;
+			clock-output-names = "en32khz_ap",
+			                     "en32khz_cp",
+			                     "en32khz_bt";
+		};
+
+		regulators {
+			s5m_ldo4_reg: LDO4 {
+				regulator-name = "P1.0V_LDO_OUT4";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				op_mode = <0>;
+			};
+
+			s5m_ldo5_reg: LDO5 {
+				regulator-name = "P1.0V_LDO_OUT5";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				op_mode = <0>;
+			};
+
+			s5m_ldo6_reg: LDO6 {
+				regulator-name = "vdd_mydp";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo7_reg: LDO7 {
+				regulator-name = "P1.1V_LDO_OUT7";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo8_reg: LDO8 {
+				regulator-name = "P1.0V_LDO_OUT8";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo10_reg: LDO10 {
+				regulator-name = "P1.8V_LDO_OUT10";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo11_reg: LDO11 {
+				regulator-name = "P1.8V_LDO_OUT11";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				op_mode = <0>;
+			};
+
+			s5m_ldo12_reg: LDO12 {
+				regulator-name = "P3.0V_LDO_OUT12";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo13_reg: LDO13 {
+				regulator-name = "P1.8V_LDO_OUT13";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				op_mode = <0>;
+			};
+
+			s5m_ldo14_reg: LDO14 {
+				regulator-name = "P1.8V_LDO_OUT14";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo15_reg: LDO15 {
+				regulator-name = "P1.0V_LDO_OUT15";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo16_reg: LDO16 {
+				regulator-name = "P1.8V_LDO_OUT16";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				op_mode = <3>;
+			};
+
+			s5m_ldo17_reg: LDO17 {
+				regulator-name = "P2.8V_LDO_OUT17";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				op_mode = <0>;
+			};
+
+			s5m_ldo25_reg: LDO25 {
+				regulator-name = "vdd_bridge";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				op_mode = <1>;
+			};
+
+			BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			BUCK3 {
+				regulator-name = "vdd_int";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			BUCK4 {
+				regulator-name = "vdd_g3d";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			BUCK5 {
+				regulator-name = "P1.8V_BUCK_OUT5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <1>;
+			};
+
+			BUCK6 {
+				regulator-name = "P1.2V_BUCK_OUT6";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <0>;
+			};
+
+			BUCK9 {
+				regulator-name = "vdd_ummc";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+		};
+	};
+};
+
+&i2c_1 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <378000>;
+};
+
+/*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+&i2c2_bus {
+	samsung,pin-pud = <0>;
+};
+
+&i2c_2 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
+
+	hdmiddc at 50 {
+		compatible = "samsung,exynos4210-hdmiddc";
+		reg = <0x50>;
+	};
+};
+
+&i2c_3 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_4 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
+
+	cros_ec: embedded-controller {
+		compatible = "google,cros-ec-i2c";
+		reg = <0x1e>;
+		interrupts = <6 0>;
+		interrupt-parent = <&gpx1>;
+		wakeup-source;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ec_irq>;
+	};
+};
+
+&i2c_5 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_7 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
+};
+
+&i2c_8 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <378000>;
+
+	hdmiphy: hdmiphy at 38 {
+		compatible = "samsung,exynos4212-hdmiphy";
+		reg = <0x38>;
+	};
+};
+
+&i2s0 {
+	status = "okay";
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	broken-cd;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
+
+	slot at 0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc_1 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	broken-cd;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
+
+	slot at 0 {
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&pinctrl_0 {
+	s5m8767_dvs: s5m8767-dvs {
+		samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+
+	power_key_irq: power-key-irq {
+		samsung,pins = "gpx1-3";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	ec_irq: ec-irq {
+		samsung,pins = "gpx1-6";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	s5m8767_ds: s5m8767-ds {
+		samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+
+	s5m8767_irq: s5m8767-irq {
+		samsung,pins = "gpx3-2";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	lid_irq: lid-irq {
+		samsung,pins = "gpx3-5";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	hdmi_hpd_irq: hdmi-hpd-irq {
+		samsung,pins = "gpx3-7";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_1 {
+	hsic_reset: hsic-reset {
+		samsung,pins = "gpe1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&sd1_clk {
+	samsung,pin-drv = <0>;
+};
+
+&sd1_cmd {
+	samsung,pin-pud = <3>;
+	samsung,pin-drv = <0>;
+};
+
+&sd1_cd {
+	samsung,pin-drv = <0>;
+};
+
+&sd1_bus4 {
+	samsung,pin-drv = <0>;
+};
+
+&spi_1 {
+	status = "okay";
+	samsung,spi-src-clk = <0>;
+	num-cs = <1>;
+};
+
+&usbdrd_phy {
+	vbus-supply = <&usb3_vbus_reg>;
+};
+
+#include "cros-ec-keyboard.dtsi"
-- 
1.9.3




More information about the linux-arm-kernel mailing list