[PATCH v9 3/6] ARM: dts: Exynos: add CPU OPP and regulator supply property
Thomas Abraham
ta.omasab at gmail.com
Wed Jul 30 21:06:28 PDT 2014
On Thu, Jul 31, 2014 at 9:23 AM, Doug Anderson <dianders at chromium.org> wrote:
> Thomas,
>
> On Wed, Jul 30, 2014 at 8:21 PM, Thomas Abraham <ta.omasab at gmail.com> wrote:
>> Hi Doug,
>>
>> On Thu, Jul 31, 2014 at 6:07 AM, Doug Anderson <dianders at chromium.org> wrote:
>>> Thomas,
>>>
>>> On Wed, Jul 30, 2014 at 1:07 AM, Thomas Abraham <thomas.ab at samsung.com> wrote:
>>>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>>>> index d0de1f5..3b12a97 100644
>>>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>>>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>>>> @@ -575,3 +575,7 @@
>>>> usb-phy = <&usb2_phy>;
>>>> };
>>>> };
>>>> +
>>>> +&cpu0 {
>>>> + cpu0-supply = <&buck2_reg>;
>>>> +};
>>>> diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
>>>> index b4b35ad..f07e834 100644
>>>> --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
>>>> +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
>>>> @@ -414,3 +414,7 @@
>>>> };
>>>> };
>>>> };
>>>> +
>>>> +&cpu0 {
>>>> + cpu0-supply = <&buck2_reg>;
>>>> +};
>>>> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
>>>> index f2b8c41..91acca7 100644
>>>> --- a/arch/arm/boot/dts/exynos5250-snow.dts
>>>> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
>>>> @@ -509,4 +509,8 @@
>>>> };
>>>> };
>>>>
>>>> +&cpu0 {
>>>> + cpu0-supply = <&buck2_reg>;
>>>> +};
>>>> +
>>>> #include "cros-ec-keyboard.dtsi"
>>>> diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
>>>> index 492e1ef..97b282c 100644
>>>> --- a/arch/arm/boot/dts/exynos5250.dtsi
>>>> +++ b/arch/arm/boot/dts/exynos5250.dtsi
>>>> @@ -58,11 +58,34 @@
>>>> #address-cells = <1>;
>>>> #size-cells = <0>;
>>>>
>>>> - cpu at 0 {
>>>> + cpu0: cpu at 0 {
>>>> device_type = "cpu";
>>>> compatible = "arm,cortex-a15";
>>>> reg = <0>;
>>>> clock-frequency = <1700000000>;
>>>> +
>>>> + clocks = <&clock CLK_ARM_CLK>;
>>>> + clock-names = "cpu";
>>>> + clock-latency = <140000>;
>>>
>>> Where did the 140000 number come from? My old calculations show that
>>> with lock time of 270 ad P up to 6 we were at 67.5us lock time.
>>
>> I measured the time taken by clk_set_rate call in the cpufreq driver
>> using do_gettimeofday(). The time taken to change the clock speed was
>> between 87us to 134us for Exynos5420. So I just took the worst case
>> time of 140us. Also, the time taken to change the CPU clock speed
>> includes the settling time for changes to dividers and mux clock
>> blocks.
>
> Interesting. I wonder why the difference between my earlier
> calculations. It seems just about double. :-/
In your calculation, only the PLL lock time is being considered. But
the 140us latency is for the whole clk_set_rate() call.
>
>
>>>> + operating-points = <
>>>> + 1700000 1300000
>>>> + 1600000 1250000
>>>> + 1500000 1225000
>>>> + 1400000 1200000
>>>> + 1300000 1150000
>>>> + 1200000 1125000
>>>> + 1100000 1100000
>>>> + 1000000 1075000
>>>> + 900000 1050000
>>>> + 800000 1025000
>>>> + 700000 1012500
>>>> + 600000 1000000
>>>> + 500000 975000
>>>> + 400000 950000
>>>> + 300000 937500
>>>> + 200000 925000
>>>> + >;
>>>> };
>>>> cpu at 1 {
>>>> device_type = "cpu";
>>>> diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
>>>> index cb2b70e..3154b4c 100644
>>>> --- a/arch/arm/boot/dts/exynos5420.dtsi
>>>> +++ b/arch/arm/boot/dts/exynos5420.dtsi
>>>> @@ -59,8 +59,26 @@
>>>> device_type = "cpu";
>>>> compatible = "arm,cortex-a15";
>>>> reg = <0x0>;
>>>> + clocks = <&clock CLK_ARM_CLK>;
>>>> + clock-names = "cpu-cluster.0";
>>>> clock-frequency = <1800000000>;
>>>> cci-control-port = <&cci_control1>;
>>>> + clock-latency = <140000>;
>>>> +
>>>> + operating-points = <
>>>> + 1800000 1250000
>>>> + 1700000 1212500
>>>> + 1600000 1175000
>>>> + 1500000 1137500
>>>> + 1400000 1112500
>>>> + 1300000 1062500
>>>> + 1200000 1037500
>>>> + 1100000 1012500
>>>> + 1000000 987500
>>>> + 900000 962500
>>>> + 800000 937500
>>>> + 700000 912500
>>>> + >;
>>>> };
>>>>
>>>> cpu1: cpu at 1 {
>>>> @@ -69,6 +87,7 @@
>>>> reg = <0x1>;
>>>> clock-frequency = <1800000000>;
>>>> cci-control-port = <&cci_control1>;
>>>> + clock-latency = <140000>;
>>>> };
>>>>
>>>> cpu2: cpu at 2 {
>>>> @@ -77,6 +96,7 @@
>>>> reg = <0x2>;
>>>> clock-frequency = <1800000000>;
>>>> cci-control-port = <&cci_control1>;
>>>> + clock-latency = <140000>;
>>>> };
>>>>
>>>> cpu3: cpu at 3 {
>>>> @@ -85,14 +105,29 @@
>>>> reg = <0x3>;
>>>> clock-frequency = <1800000000>;
>>>> cci-control-port = <&cci_control1>;
>>>> + clock-latency = <140000>;
>>>> };
>>>>
>>>> cpu4: cpu at 100 {
>>>> device_type = "cpu";
>>>> compatible = "arm,cortex-a7";
>>>> reg = <0x100>;
>>>> + clocks = <&clock CLK_KFC_CLK>;
>>>> + clock-names = "cpu-cluster.1";
>>>> clock-frequency = <1000000000>;
>>>
>>> It does't start out at its maximum?
>>
>> The A7 CPU clock need not start with the maximum. On the SMDK5420
>> board, the firmware has set the A7 CPU clock to 1GHz. So I used the
>> same value here.
>
> Does it need to match the firmware? On exynos5420-peach-pit and
> peach-pi I think the firmware starts the kernel at 1.7GHz.
It need not strictly match with the firmware. 1.7GHz for A7 seems too
high since the max A7 speed was 1.3GHz. Probably peach-pit/pi had
600MHz starting frequency for A7 CPU.
Thanks,
Thomas.
>
>
>>>> cci-control-port = <&cci_control0>;
>>>> + clock-latency = <140000>;
>>>> +
>>>> + operating-points = <
>>>> + 1300000 1275000
>>>> + 1200000 1212500
>>>> + 1100000 1162500
>>>> + 1000000 1112500
>>>> + 900000 1062500
>>>> + 800000 1025000
>>>> + 700000 975000
>>>> + 600000 937500
>>>> + >;
>>>> };
>>>>
>>>> cpu5: cpu at 101 {
>>>> @@ -101,6 +136,7 @@
>>>> reg = <0x101>;
>>>> clock-frequency = <1000000000>;
>>>> cci-control-port = <&cci_control0>;
>>>> + clock-latency = <140000>;
>>>> };
>>>>
>>>> cpu6: cpu at 102 {
>>>> @@ -109,6 +145,7 @@
>>>> reg = <0x102>;
>>>> clock-frequency = <1000000000>;
>>>> cci-control-port = <&cci_control0>;
>>>> + clock-latency = <140000>;
>>>> };
>>>>
>>>> cpu7: cpu at 103 {
>>>> @@ -117,6 +154,7 @@
>>>> reg = <0x103>;
>>>> clock-frequency = <1000000000>;
>>>> cci-control-port = <&cci_control0>;
>>>> + clock-latency = <140000>;
>>>> };
>>>> };
>>>
>>> Don't you need to put a reference to the supply in the 5420 board
>>> files? ...or is that not possible yet since the max77802 hasn't
>>> landed yet?
>>
>> The arm big.little cpufreq driver does not have voltage scaling
>> support yet. So the supply was not mentioned.
>>
>>>
>>> If that's not possible, is there any reason to post the 5420.dtsi
>>> patch now? Also: what about 5800? It's so similar to 5420 that it
>>> seems a shame not to do them at the same time.
>>
>> This patch series has support for Exynos5800 as well. But it is A15
>> clock is restricted to 1.8GHz for now since we do not have a way to
>> handle the vdd_arm and vdd_int voltage difference with 1.9GHz and
>> 2.0GHZ in upstream yet.
>
> Oh, right! The 5800 includes the 5420 dtsi...
>
> -Doug
More information about the linux-arm-kernel
mailing list