[PATCH 19/19] Documentation: ACPI for ARM64

[Mark Rutland]

On Mon, Jul 28, 2014 at 05:33:13PM +0100, Olof Johansson wrote:
> On Mon, Jul 28, 2014 at 11:12:29AM +0100, Mark Rutland wrote:
> > On Mon, Jul 28, 2014 at 10:07:50AM +0100, Arnd Bergmann wrote:
> > > On Saturday 26 July 2014 19:34:48 Olof Johansson wrote:
> > > > On Thu, Jul 24, 2014 at 6:00 AM, Hanjun Guo <hanjun.guo at linaro.org> wrote:
> > > > > +Relationship with Device Tree
> > > > > +-----------------------------
> > > > > +
> > > > > +ACPI support in drivers and subsystems for ARMv8 should never be mutually
> > > > > +exclusive with DT support at compile time.
> > > > > +
> > > > > +At boot time the kernel will only use one description method depending on
> > > > > +parameters passed from the bootloader.
> > > > 
> > > > Possibly overriden by kernel bootargs. And as debated for quite a
> > > > while earlier this year, acpi should still default to off -- if a DT
> > > > and ACPI are both passed in, DT should at this time be given priority.
> > > 
> > > I think this would be harder to do with the way that ACPI is passed in
> > > to the kernel. IIRC, you always have a minimal DT information based on
> > > the ARM64 boot protocol, but in the case of ACPI, this contains pointers
> > > to the ACPI tables, which are then used for populating the Linux platform
> > > devices (unless acpi=disabled is set), while the other contents of the
> > > DTB may be present but we skip the of_platform_populate state.
> > > 
> > > If this is correct, then replacing the firmware-generated dtb with a
> > > user-provided on would implicitly remove the ACPI tables from visibility,
> > > which is exactly what we want.
> > 
> > That's not quite true.
> > 
> > There might not be any DTB, or the user might have provided a DTB with
> > only /chosen/bootargs. Trying to distinguish the many cases of possible
> > DTB is broken as a concept.
> > 
> > The EFI stub will attempt to get a DTB from somewhere (provided by
> > filename or as a system table with a magic UUID), and if it can't find
> > one will generate an empty stub DTB.
> > 
> > Then it will go and perform some EFI memory setup, placing some
> > properties in the DTB (which might be a stub) describing the EFI memory
> > map.
> > 
> > Then we boot the kernel proper, which sees the EFI pointers and looks
> > for an ACPI table. If they are found, ACPI is used. Otherwise we attempt
> > to use the DTB (which might be a stub).
> > 
> > Unless ACPI is explcitly disabled, ACPI will be used if present.
> 
> Ah, I saw this after I replied to Arnd's email.
> 
> The above sounds more like how I envisioned things working, so based on that,
> the default just needs to be flipped and we should be fine (i.e. ACPI needs to
> be explicitly enabled).

Sorry, but I don't follow your reasoning. What is the rationale for
disabling ACPI by default?

That's not going to work for ACPI-only systems which may not have any HW
described in a DTB. I fear it will result in more pain on any systems
which try to ship both ACPI and DT, where ACPI will not get the testing
it requires, leading to a greater possibility of quirks/workarounds
being required later.

Thanks,
Mark.