[PATCH 1/2] iio: adc: exynos_adc: add support for s3c64xx adc

[Chanwoo Choi]

On 07/28/2014 03:49 AM, Hartmut Knaack wrote:
> Chanwoo Choi schrieb:
>> From: Arnd Bergmann <arnd at arndb.de>
>>
>> The ADC in s3c64xx is almost the same as exynosv1, but
>> has a different 'select' method. Adding this here will be
>> helpful to move over the existing s3c64xx platform from the
>> legacy plat-samsung/adc driver to the new exynos-adc.
>>
>> Signed-off-by: Arnd Bergmann <arnd at arndb.de>
>> Signed-off-by: Chanwoo Choi <cw00.choi at samsung.com>
>> ---
>>  .../devicetree/bindings/arm/samsung/exynos-adc.txt |  2 ++
>>  drivers/iio/adc/exynos_adc.c                       | 32 +++++++++++++++++++++-
>>  2 files changed, 33 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt
>> index 6d34891..b6e3989 100644
>> --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt
>> +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt
>> @@ -16,6 +16,8 @@ Required properties:
>>  				future controllers.
>>  			Must be "samsung,exynos3250-adc" for
>>  				controllers compatible with ADC of Exynos3250.
>> +			Must be "samsung,s3c6410-adc" for
>> +				the ADC in s3c6410 and compatibles
>>  - reg:			Contains ADC register address range (base address and
>>  			length) and the address of the phy enable register.
>>  - interrupts: 		Contains the interrupt information for the timer. The
>> diff --git a/drivers/iio/adc/exynos_adc.c b/drivers/iio/adc/exynos_adc.c
>> index 87e0895..05bdd2f12 100644
>> --- a/drivers/iio/adc/exynos_adc.c
>> +++ b/drivers/iio/adc/exynos_adc.c
>> @@ -40,12 +40,16 @@
>>  #include <linux/iio/machine.h>
>>  #include <linux/iio/driver.h>
>>  
>> -/* EXYNOS4412/5250 ADC_V1 registers definitions */
>> +/* S3C/EXYNOS4412/5250 ADC_V1 registers definitions */
>>  #define ADC_V1_CON(x)		((x) + 0x00)
>> +#define ADC_V1_TSC(x)		((x) + 0x04)
>>  #define ADC_V1_DLY(x)		((x) + 0x08)
>>  #define ADC_V1_DATX(x)		((x) + 0x0C)
>> +#define ADC_V1_DATY(x)		((x) + 0x10)
>> +#define ADC_V1_UPDN(x)		((x) + 0x14)
>>  #define ADC_V1_INTCLR(x)	((x) + 0x18)
>>  #define ADC_V1_MUX(x)		((x) + 0x1c)
>> +#define ADC_V1_CLRINTPNDNUP(x)	((x) + 0x20)
>>  
>>  /* Future ADC_V2 registers definitions */
>>  #define ADC_V2_CON1(x)		((x) + 0x00)
>> @@ -61,6 +65,9 @@
>>  #define ADC_V1_CON_PRSCLV(x)	(((x) & 0xFF) << 6)
>>  #define ADC_V1_CON_STANDBY	(1u << 2)
>>  
>> +/* Bit definitions for S3C2410 ADC */
>> +#define ADC_S3C2410_CON_SELMUX(x) (((x) & 7) <<3)
> There is a whitespace missing.

OK, I'll fix it.

Best Regards,
Chanwoo Choi