[PATCH 2/2] ARM: mvebu: Added dts defintion for Lenovo Iomega ix4-300d NAS
Benoit Masson
benoitm at perenite.com
Sat Jul 26 16:55:48 PDT 2014
Andrew, Jason,
Le 26 juil. 2014 à 19:26, Andrew Lunn <andrew at lunn.ch> a écrit :
> On Wed, Jul 23, 2014 at 03:52:53PM -0700, Benoit Masson wrote:
>> The Lenovo Iomega ix4-300d is a 4-Bay sata NAS with dual Gb,
>> USB2.0 & 3.0, powered by a Marvell Armada XP MV78230 dual core CPU.
>
> Hi Benoit
>
> Please could you change the i2c compatible string, and retest
> including the two patches i just sent.
>
I confirm the V3 patch i sent (sorry for the first patch email which was wrong) is working with your patch
> Once that is done, i think your patch is ready for acceptance. It is
> however a bit late for this cycle, so i guess Jason will keep hold of
> it until the next cycle.
>
Ok, jason, I did include the multi-line comment remarks in V3 patch, also I didn't resend the Lenovo vendor list patch, that was already acked I hope It's fine.
Benoit
> Thanks
> Andrew
>
>
>>
>> http://shop.lenovo.com/fr/fr/servers/network-storage/lenovoemc/ix4-300d/
>> Signed-off-by: Benoit Masson <yahoo at perenite.com>
>> ---
>> arch/arm/boot/dts/Makefile | 3 +-
>> arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts | 284 ++++++++++++++++++++++++
>> 2 files changed, 286 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index adb5ed9..4429495 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -437,8 +437,9 @@ dtb-$(CONFIG_MACH_ARMADA_XP) += \
>> armada-xp-axpwifiap.dtb \
>> armada-xp-db.dtb \
>> armada-xp-gp.dtb \
>> - armada-xp-netgear-rn2120.dtb \
>> + armada-xp-lenovo-ix4-300d.dtb \
>> armada-xp-matrix.dtb \
>> + armada-xp-netgear-rn2120.dtb \
>> armada-xp-openblocks-ax3-4.dtb
>> dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
>> dove-cubox.dtb \
>> diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
>> new file mode 100644
>> index 0000000..1f33cbc
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
>> @@ -0,0 +1,284 @@
>> +/*
>> + * Device Tree file for Lenovo Iomega ix4-300d
>> + *
>> + * Copyright (C) 2014, Benoit Masson <yahoo at perenite.com>
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License
>> + * as published by the Free Software Foundation; either version
>> + * 2 of the License, or (at your option) any later version.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include "armada-xp-mv78230.dtsi"
>> +
>> +/ {
>> + model = "Lenovo Iomega ix4-300d";
>> + compatible = "lenovo,ix4-300d", "marvell,armadaxp-mv78230",
>> + "marvell,armadaxp", "marvell,armada-370-xp";
>> +
>> + chosen {
>> + bootargs = "console=ttyS0,115200 earlyprintk";
>> + stdout-path = "/soc/internal-regs/serial at 12000";
>> + };
>> +
>> + memory {
>> + device_type = "memory";
>> + reg = <0 0x00000000 0 0x20000000>; /* 512MB */
>> + };
>> +
>> + soc {
>> + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
>> + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
>> +
>> + pcie-controller {
>> + status = "okay";
>> +
>> + /* Quad port sata: Marvell 88SX7042 */
>> + pcie at 1,0 {
>> + /* Port 0, Lane 0 */
>> + status = "okay";
>> + };
>> +
>> + /* USB 3.0 xHCI controller: NEC D720200F1 */
>> + pcie at 5,0 {
>> + /* Port 1, Lane 0 */
>> + status = "okay";
>> + };
>> + };
>> +
>> + internal-regs {
>> + pinctrl {
>> + poweroff_pin: poweroff-pin {
>> + marvell,pins = "mpp24";
>> + marvell,function = "gpio";
>> + };
>> +
>> + power_button_pin: power-button-pin {
>> + marvell,pins = "mpp44";
>> + marvell,function = "gpio";
>> + };
>> +
>> + reset_button_pin: reset-button-pin {
>> + marvell,pins = "mpp45";
>> + marvell,function = "gpio";
>> + };
>> + select_button_pin: select-button-pin {
>> + marvell,pins = "mpp41";
>> + marvell,function = "gpio";
>> + };
>> +
>> + scroll_button_pin: scroll-button-pin {
>> + marvell,pins = "mpp42";
>> + marvell,function = "gpio";
>> + };
>> +
>> + hdd_led_pin: hdd-led-pin {
>> + marvell,pins = "mpp26";
>> + marvell,function = "gpio";
>> + };
>> + };
>> +
>> + serial at 12000 {
>> + status = "okay";
>> + };
>> +
>> + mdio {
>> + phy0: ethernet-phy at 0 { /* Marvell 88E1318 */
>> + reg = <0>;
>> + };
>> +
>> + phy1: ethernet-phy at 1 { /* Marvell 88E1318 */
>> + reg = <1>;
>> + };
>> + };
>> +
>> + ethernet at 70000 {
>> + status = "okay";
>> + phy = <&phy0>;
>> + phy-mode = "rgmii-id";
>> + };
>> +
>> + ethernet at 74000 {
>> + status = "okay";
>> + phy = <&phy1>;
>> + phy-mode = "rgmii-id";
>> + };
>> +
>> + usb at 50000 {
>> + status = "okay";
>> + };
>> +
>> + usb at 51000 {
>> + status = "okay";
>> + };
>> +
>> + i2c at 11000 {
>> + compatible = "marvell,mv78230-a0-i2c",
>> + "marvell,mv64xxx-i2c";
>> + clock-frequency = <400000>;
>> + status = "okay";
>> +
>> + adt7473 at 2e {
>> + compatible = "adi,adt7473";
>> + reg = <0x2e>;
>> + };
>> +
>> + pcf8563 at 51 {
>> + compatible = "nxp,pcf8563";
>> + reg = <0x51>;
>> + };
>> +
>> + };
>> +
>> + nand at d0000 {
>> + status = "okay";
>> + num-cs = <1>;
>> + marvell,nand-keep-config;
>> + marvell,nand-enable-arbiter;
>> + nand-on-flash-bbt;
>> +
>> + partition at 0 {
>> + label = "u-boot";
>> + reg = <0x0000000 0xe0000>;
>> + read-only;
>> + };
>> +
>> + partition at e0000 {
>> + label = "u-boot-env";
>> + reg = <0xe0000 0x20000>;
>> + read-only;
>> + };
>> +
>> + partition at 100000 {
>> + label = "u-boot-env2";
>> + reg = <0x100000 0x20000>;
>> + read-only;
>> + };
>> +
>> + partition at 120000 {
>> + label = "zImage";
>> + reg = <0x120000 0x400000>;
>> + };
>> +
>> + partition at 520000 {
>> + label = "initrd";
>> + reg = <0x520000 0x400000>;
>> + };
>> +
>> + partition at xE00000 {
>> + label = "boot";
>> + reg = <0xE00000 0x3F200000>;
>> + };
>> +
>> + partition at flash {
>> + label = "flash";
>> + reg = <0x0 0x40000000>;
>> + };
>> + };
>> + };
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> + pinctrl-0 = <&power_button_pin &reset_button_pin
>> + &select_button_pin &scroll_button_pin>;
>> + pinctrl-names = "default";
>> +
>> + power-button {
>> + label = "Power Button";
>> + linux,code = <KEY_POWER>;
>> + gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + reset-button {
>> + label = "Reset Button";
>> + linux,code = <KEY_RESTART>;
>> + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + select-button {
>> + label = "Select Button";
>> + linux,code = <BTN_SELECT>;
>> + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + scroll-button {
>> + label = "Scroll Button";
>> + linux,code = <KEY_SCROLLDOWN>;
>> + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + spi3 {
>> + compatible = "spi-gpio";
>> + status = "okay";
>> + gpio-sck = <&gpio0 25 0>;
>> + gpio-mosi = <&gpio1 15 0>; /*gpio 47*/
>> + cs-gpios = <&gpio0 27 0 >;
>> + num-chipselects = <1>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + gpio2: gpio2 at 0 {
>> + compatible = "fairchild,74hc595";
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + reg = <0>;
>> + registers-number = <2>;
>> + spi-max-frequency = <100000>;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> + pinctrl-0 = <&hdd_led_pin>;
>> + pinctrl-names = "default";
>> +
>> + hdd-led {
>> + label = "ix4-300d:hdd:blue";
>> + gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + };
>> +
>> + power-led {
>> + label = "ix4-300d:power:white";
>> + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
>> + /* init blinking while booting */
>> + linux,default-trigger = "timer";
>> + default-state = "on";
>> + };
>> +
>> + sysfail-led {
>> + label = "ix4-300d:sysfail:red";
>> + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + };
>> +
>> + sys-led {
>> + label = "ix4-300d:sys:blue";
>> + gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + };
>> +
>> + hddfail-led {
>> + label = "ix4-300d:hddfail:red";
>> + gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + };
>> +
>> + };
>> +
>> + /* Warning: you need both eth1 & 0 PHY initialized
>> + (i.e having them up does the tweak)
>> + for poweroff to shutdown otherwise it reboots */
>> + gpio-poweroff {
>> + compatible = "gpio-poweroff";
>> + pinctrl-0 = <&poweroff_pin>;
>> + pinctrl-names = "default";
>> + gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
>> + };
>> +};
>> --
>> 1.9.1
>>
More information about the linux-arm-kernel
mailing list