[PATCH v4] pcie: Add Xilinx PCIe Host Bridge IP driver
Srikanth Thokala
sthokal at xilinx.com
Mon Jul 21 22:10:48 PDT 2014
Hi Bjorn,
On Wed, Jul 16, 2014 at 11:08 PM, Bjorn Helgaas <bhelgaas at google.com> wrote:
> On Thu, Jul 03, 2014 at 09:57:34AM +0530, Srikanth Thokala wrote:
>> This is the driver for Xilinx AXI PCIe Host Bridge Soft IP
>>
>> Signed-off-by: Srikanth Thokala <sthokal at xilinx.com>
>> ---
>> Changes in v4:
>> - Regarding the comments to separate ECAM functionality,
>> I have sent a separate patch and it is decided to implement
>> it later. The patch is here,
>> https://lkml.org/lkml/2014/5/18/54
>> - Fixed issue with adding configuration bus resource.
>> - Moved the logic for setting up bus resources to probe() from
>> pcie_setup().
>> - Instead of mapping all the MSI interrupts in the probe, changed
>> to map only when a MSI is requested.
>> - Earlier, the implementation of legacy and MSI interrupts init-
>> is mutually exclusive, now changed to have the legacy interrupts
>> init always and MSI interrupt init based on CONFIG_PCI_MSI flag.
>> - Regarding the MSI generic implementation comment, I will plan to
>> do on top of this driver patch.
>> - Rebased on 3.16-rc2.
>> - Fixed other minor comments.
>> - Thanks Arnd and Bjorn for the review.
>>
>> Changes in v3:
>> - Rebased on v3.15.0-rc1
>> - Added support for interrupt-map DT functionality.
>> - Removed map_irq() wrapper, instead using of_irq_parse_and_map_pci().
>> - Modified resource mapping logic as per the series
>> "PCI: ARM: add support for generic PCI host controller"
>> - Modified devicetree binding documentation to update with interrupt-
>> map properties.
>> - Use devm calls wherever applicable.
>> - Fixed minor comments from Jason
>> - Thanks Jason for the review and suggestions.
>>
>> Changes in v2:
>> - Rebased on v3.14.0-rc8
>> - Removed IP specific DT properties like include-rc, axibar-num etc.,
>> as suggested by Jason and Bjorn, Thanks
>> ---
>> .../devicetree/bindings/pci/xilinx-pcie.txt | 62 ++
>> drivers/pci/host/Kconfig | 7 +
>> drivers/pci/host/Makefile | 1 +
>> drivers/pci/host/pci-xilinx.c | 1027 ++++++++++++++++++++
>> 4 files changed, 1097 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pci/xilinx-pcie.txt
>> create mode 100644 drivers/pci/host/pci-xilinx.c
>
> I see I forgot to ask for a MAINTAINERS entry for this driver. Can
> you add one?
There was a discussion on this earlier and Michal mentioned it is not
required as it is
handled by our Xilinx record.
Here is the reply from Michal to the MAINTAINERS update comment,
< Reply from Michal >
> Please also include a MAINTAINERS update for drivers/pci/host/pci-xilinx.c.
This should be handle by our record that's why MAINTAINERS update is
not necessary.
(N: xilinx below)
ARM/ZYNQ ARCHITECTURE
M: Michal Simek <michal.simek at xilinx.com>
L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
W: http://wiki.xilinx.com
T: git git://git.xilinx.com/linux-xlnx.git
S: Supported
F: arch/arm/mach-zynq/
F: drivers/cpuidle/cpuidle-zynq.c
N: zynq
N: xilinx
F: drivers/clocksource/cadence_ttc_timer.c
F: drivers/mmc/host/sdhci-of-arasan.c
Thanks,
Michal
< Reply from Michal >
>
> I'd also like an ack from Arnd or another devicetree person for the
> binding.
Sure, I will request them.
>
> I have a few minor comments below.
Sure.
>
>> diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
>> new file mode 100644
>> index 0000000..3e2c88d
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
>> @@ -0,0 +1,62 @@
>> +* Xilinx AXI PCIe Root Port Bridge DT description
>> +
>> +Required properties:
>> +- #address-cells: Address representation for root ports, set to <3>
>> +- #size-cells: Size representation for root ports, set to <2>
>> +- #interrupt-cells: specifies the number of cells needed to encode an
>> + interrupt source. The value must be 1.
>> +- compatible: Should contain "xlnx,axi-pcie-host-1.00.a"
>> +- reg: Should contain AXI PCIe registers location and length
>> +- device_type: must be "pci"
>> +- interrupts: Should contain AXI PCIe interrupt
>> +- interrupt-map-mask,
>> + interrupt-map: standard PCI properties to define the mapping of the
>> + PCI interface to interrupt numbers.
>> +- ranges: ranges for the PCI memory regions (I/O space region is not
>> + supported by hardware)
>> + Please refer to the standard PCI bus binding document for a more
>> + detailed explanation
>> +
>> +Optional properties:
>> +- bus-range: PCI bus numbers covered
>> +
>> +Interrupt controller child node
>> ++++++++++++++++++++++++++++++++
>> +Required properties:
>> +- interrupt-controller: identifies the node as an interrupt controller
>> +- #address-cells: specifies the number of cells needed to encode an
>> + address. The value must be 0.
>> +- #interrupt-cells: specifies the number of cells needed to encode an
>> + interrupt source. The value must be 1.
>> +
>> +NOTE:
>> +The core provides a single interrupt for both INTx/MSI messages. So,
>> +created a interrupt controller node to support 'interrupt-map' DT
>> +functionality. The driver will create an IRQ domain for this map, decode
>> +the four INTx interrupts in ISR and route them to this domain.
>> +
>> +
>> +Example:
>> +++++++++
>> +
>> + pci_express: axi-pcie at 50000000 {
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + #interrupt-cells = <1>;
>> + compatible = "xlnx,axi-pcie-host-1.00.a";
>> + reg = < 0x50000000 0x10000000 >;
>> + device_type = "pci";
>> + interrupts = < 0 52 4 >;
>> + interrupt-map-mask = <0 0 0 7>;
>> + interrupt-map = <0 0 0 1 &pcie_intc 1>,
>> + <0 0 0 2 &pcie_intc 2>,
>> + <0 0 0 3 &pcie_intc 3>,
>> + <0 0 0 4 &pcie_intc 4>;
>> + ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >;
>> +
>> + pcie_intc: interrupt-controller {
>> + interrupt-controller;
>> + #address-cells = <0>;
>> + #interrupt-cells = <1>;
>> + }
>> + };
>> diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
>> index 21df477..afedcde 100644
>> --- a/drivers/pci/host/Kconfig
>> +++ b/drivers/pci/host/Kconfig
>> @@ -46,4 +46,11 @@ config PCI_HOST_GENERIC
>> Say Y here if you want to support a simple generic PCI host
>> controller, such as the one emulated by kvmtool.
>>
>> +config PCI_XILINX
>> + bool "Xilinx AXI PCIe host bridge support"
>> + depends on ARCH_ZYNQ
>> + help
>> + Say 'Y' here if you want kernel to support the Xilinx AXI PCIe
>> + Host Bridge driver.
>> +
>> endmenu
>> diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
>> index 611ba4b..68dfd06 100644
>> --- a/drivers/pci/host/Makefile
>> +++ b/drivers/pci/host/Makefile
>> @@ -6,3 +6,4 @@ obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
>> obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
>> obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o
>> obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
>> +obj-$(CONFIG_PCI_XILINX) += pci-xilinx.o
>> diff --git a/drivers/pci/host/pci-xilinx.c b/drivers/pci/host/pci-xilinx.c
>> new file mode 100644
>> index 0000000..57d59e7
>> --- /dev/null
>> +++ b/drivers/pci/host/pci-xilinx.c
>> @@ -0,0 +1,1027 @@
>> +/*
>> + * PCIe host controller driver for Xilinx AXI PCIe Bridge
>> + *
>> + * Copyright (c) 2012 - 2014 Xilinx, Inc.
>> + *
>> + * Based on the Tegra PCIe driver
>> + *
>> + * Bits taken from Synopsys Designware Host controller driver and
>> + * ARM PCI Host generic driver.
>> + *
>> + * This program is free software: you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation, either version 2 of the License, or
>> + * (at your option) any later version.
>> + */
>> +
>> +#include <linux/interrupt.h>
>> +#include <linux/irq.h>
>> +#include <linux/irqdomain.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/msi.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_pci.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/pci.h>
>> +#include <linux/platform_device.h>
>> +
>> +/* Register definitions */
>> +#define XILINX_PCIE_REG_VSECC 0x00000128
>> +#define XILINX_PCIE_REG_VSECH 0x0000012c
>> +#define XILINX_PCIE_REG_BIR 0x00000130
>> +#define XILINX_PCIE_REG_BSCR 0x00000134
>> +#define XILINX_PCIE_REG_IDR 0x00000138
>> +#define XILINX_PCIE_REG_IMR 0x0000013c
>> +#define XILINX_PCIE_REG_BLR 0x00000140
>> +#define XILINX_PCIE_REG_PSCR 0x00000144
>> +#define XILINX_PCIE_REG_RPSC 0x00000148
>> +#define XILINX_PCIE_REG_MSIBASE1 0x0000014c
>> +#define XILINX_PCIE_REG_MSIBASE2 0x00000150
>> +#define XILINX_PCIE_REG_RPEFR 0x00000154
>> +#define XILINX_PCIE_REG_RPIFR1 0x00000158
>> +#define XILINX_PCIE_REG_RPIFR2 0x0000015c
>> +#define XILINX_PCIE_REG_VSECC2 0x00000200
>> +#define XILINX_PCIE_REG_VSECH2 0x00000204
>> +
>> +/* Interrupt registers definitions */
>> +#define XILINX_PCIE_INTR_LINK_DOWN BIT(0)
>> +#define XILINX_PCIE_INTR_ECRC_ERR BIT(1)
>> +#define XILINX_PCIE_INTR_STR_ERR BIT(2)
>> +#define XILINX_PCIE_INTR_HOT_RESET BIT(3)
>> +#define XILINX_PCIE_INTR_CFG_COMPL GENMASK(7, 5)
>> +#define XILINX_PCIE_INTR_CFG_TIMEOUT BIT(8)
>> +#define XILINX_PCIE_INTR_CORRECTABLE BIT(9)
>> +#define XILINX_PCIE_INTR_NONFATAL BIT(10)
>> +#define XILINX_PCIE_INTR_FATAL BIT(11)
>> +#define XILINX_PCIE_INTR_INTX BIT(16)
>> +#define XILINX_PCIE_INTR_MSI BIT(17)
>> +#define XILINX_PCIE_INTR_SLV_UNSUPP BIT(20)
>> +#define XILINX_PCIE_INTR_SLV_UNEXP BIT(21)
>> +#define XILINX_PCIE_INTR_SLV_COMPL BIT(22)
>> +#define XILINX_PCIE_INTR_SLV_ERRP BIT(23)
>> +#define XILINX_PCIE_INTR_SLV_CMPABT BIT(24)
>> +#define XILINX_PCIE_INTR_SLV_ILLBUR BIT(25)
>> +#define XILINX_PCIE_INTR_MST_DECERR BIT(26)
>> +#define XILINX_PCIE_INTR_MST_SLVERR BIT(27)
>> +#define XILINX_PCIE_INTR_MST_ERRP BIT(28)
>> +#define XILINX_PCIE_IMR_ALL_MASK 0x1FF30FED
>> +#define XILINX_PCIE_IDR_ALL_MASK 0xFFFFFFFF
>> +
>> +/* Root Port Error FIFO Read Register definitions */
>> +#define XILINX_PCIE_RPEFR_ERR_VALID BIT(18)
>> +#define XILINX_PCIE_RPEFR_REQ_ID GENMASK(15, 0)
>> +#define XILINX_PCIE_RPEFR_ALL_MASK 0xFFFFFFFF
>> +
>> +/* Root Port Interrupt FIFO Read Register 1 definitions */
>> +#define XILINX_PCIE_RPIFR1_INTR_VALID BIT(31)
>> +#define XILINX_PCIE_RPIFR1_MSI_INTR BIT(30)
>> +#define XILINX_PCIE_RPIFR1_INTR_ASSRT BIT(29)
>> +#define XILINX_PCIE_RPIFR1_INTR_MASK GENMASK(28, 27)
>> +#define XILINX_PCIE_RPIFR1_MSI_ADR_MASK GENMASK(26, 16)
>> +#define XILINX_PCIE_RPIFR1_ALL_MASK 0xFFFFFFFF
>> +#define XILINX_PCIE_RPIFR1_INTR_SHIFT 27
>> +#define XILINX_PCIE_RPIFR1_MSI_ADR_SHIFT 16
>> +
>> +/* Bridge Info Register definitions */
>> +#define XILINX_PCIE_BIR_ECAM_SZ_MASK GENMASK(18, 16)
>> +#define XILINX_PCIE_BIR_ECAM_SZ_SHIFT 16
>> +
>> +/* Root Port Interrupt FIFO Read Register 2 definitions */
>> +#define XILINX_PCIE_RPIFR2_MSG_DATA GENMASK(15, 0)
>> +
>> +/* Root Port Status/control Register definitions */
>> +#define XILINX_PCIE_REG_RPSC_BEN BIT(0)
>> +
>> +/* Phy Status/Control Register definitions */
>> +#define XILINX_PCIE_REG_PSCR_LNKUP BIT(11)
>> +
>> +/* ECAM definitions */
>> +#define ECAM_BUS_NUM_SHIFT 20
>> +#define ECAM_DEV_NUM_SHIFT 12
>> +
>> +/* PCI Configuration space Bus Number Register definitions */
>> +#define PCI_SECONDARY_BUS_NUM_SHIFT 8
>> +#define PCI_SUBORDINATE_BUS_NUM_SHIFT 16
>> +#define PCI_LATENCY_TIMER_MASK GENMASK(31, 24)
>
> These three #defines aren't used; can you remove them? (If you need
> them someday, you should either try to use generic definitions from
> include/uapi/linux/pci_regs.h, or if they're Xilinx-specific, rename
> them so they look Xilinx-specific rather than generic.
Ok.
>
>> +
>> +/* Number of MSI IRQs */
>> +#define XILINX_NUM_MSI_IRQS 128
>> +
>> +/* Number of Memory Resources */
>> +#define XILINX_MAX_NUM_RESOURCES 3
>> +
>> +/**
>> + * struct xilinx_pcie_port - PCIe port information
>> + * @reg_base: IO Mapped Register Base
>> + * @irq: Interrupt number
>> + * @msi_pages: MSI pages
>> + * @root_busno: Root Bus number
>> + * @link_up: Link status flag
>> + * @dev: Device pointer
>> + * @irq_domain: IRQ domain pointer
>> + * @bus_range: Bus range
>> + * @resources: Bus Resources
>> + */
>> +struct xilinx_pcie_port {
>> + void __iomem *reg_base;
>> + u32 irq;
>> + unsigned long msi_pages;
>> + u8 root_busno;
>> + bool link_up;
>> + struct device *dev;
>> + struct irq_domain *irq_domain;
>> + struct resource bus_range;
>> + struct list_head resources;
>> +};
>> +
>> +static DECLARE_BITMAP(msi_irq_in_use, XILINX_NUM_MSI_IRQS);
>> +
>> +static inline struct xilinx_pcie_port *sys_to_pcie(struct pci_sys_data *sys)
>> +{
>> + return sys->private_data;
>> +}
>> +
>> +static inline u32 pcie_read(struct xilinx_pcie_port *port, u32 reg)
>> +{
>> + return readl(port->reg_base + reg);
>> +}
>> +
>> +static inline void pcie_write(struct xilinx_pcie_port *port,
>> + u32 val, u32 reg)
>> +{
>> + writel(val, port->reg_base + reg);
>> +}
>> +
>> +static inline bool xilinx_pcie_is_link_up(struct xilinx_pcie_port *port)
>
> Bool function names should be statements or properties, not questions,
> since a statement can be true or false but a question cannot. For
> example, in this case, "xilinx_pcie_link_up()" or
> "xilinx_pcie_link_is_up()" would read better.
Ok.
>
>> +{
>> + return (pcie_read(port, XILINX_PCIE_REG_PSCR) &
>> + XILINX_PCIE_REG_PSCR_LNKUP) ? 1 : 0;
>> +}
>> +
>> +/**
>> + * xilinx_pcie_clear_err_interrupts - Clear Error Interrupts
>> + * @port: PCIe port information
>> + */
>> +static inline void
>> +xilinx_pcie_clear_err_interrupts(struct xilinx_pcie_port *port)
>
> Put the signature all on one line. It probably doesn't need to be
> inline (we're making a couple register accesses, so speed isn't a
> concern), and removing that will make it fit.
Ok.
>
>> +{
>> + u32 val = pcie_read(port, XILINX_PCIE_REG_RPEFR);
>> +
>> + if (val & XILINX_PCIE_RPEFR_ERR_VALID) {
>> + dev_dbg(port->dev, "Requester ID %d\n",
>> + val & XILINX_PCIE_RPEFR_REQ_ID);
>> + pcie_write(port, XILINX_PCIE_RPEFR_ALL_MASK,
>> + XILINX_PCIE_REG_RPEFR);
>> + }
>> +}
>> +
>> +/**
>> + * xilinx_pcie_verify_config - Verify configuration
>> + * @bus: PCI Bus structure
>> + * @devfn: device/function
>> + *
>> + * Return: 0 on success and error value for invalid configuration
>> + */
>> +static int xilinx_pcie_verify_config(struct pci_bus *bus,
>> + unsigned int devfn)
>
> "verify_config" is not a great function name because it doesn't give a
> good clue about what the return value is. If you make it boolean and
> name it, e.g., xilinx_pcie_valid_device(), then it's obvious.
Ok.
>
>> +{
>> + struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
>> +
>> + /* Check if link is up when trying to access downstream ports */
>> + if (bus->number != port->root_busno)
>> + if (!xilinx_pcie_is_link_up(port))
>> + return -EINVAL;
>> +
>> + /* Only one device down on each root port */
>> + if (bus->number == port->root_busno && devfn > 0)
>> + return -EINVAL;
>> +
>> + /*
>> + * Do not read more than one device on the bus directly attached
>> + * to RC.
>> + */
>> + if (bus->primary == port->root_busno && devfn > 0)
>> + return -EINVAL;
>> +
>> + return 0;
>> +}
>> +
>> +/**
>> + * xilinx_pcie_get_config_base - Get configuration base
>> + * @bus: PCI Bus structure
>> + * @devfn: Device/function
>> + * @where: Offset from base
>> + *
>> + * Return: Base address of the configuration space needed to be
>> + * accessed.
>> + */
>> +static void __iomem *xilinx_pcie_get_config_base(struct pci_bus *bus,
>> + unsigned int devfn,
>> + int where)
>
> "xilinx_pcie_config_base()" would be sufficient. We use "get" as a
> clue that we're acquiring a reference (obviously not an issue here,
> but I think the "get" in this function name is still a bit redundant.)
Ok.
>
>> +{
>> + struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
>> + int relbus;
>> +
>> + relbus = (bus->number << ECAM_BUS_NUM_SHIFT) |
>> + (devfn << ECAM_DEV_NUM_SHIFT);
>> +
>> + return port->reg_base + relbus + where;
>> +}
>> +
>> +/**
>> + * xilinx_pcie_read_config - Read configuration space
>> + * @bus: PCI Bus structure
>> + * @devfn: Device/function
>> + * @where: Offset from base
>> + * @size: Byte/word/dword
>> + * @val: Value to be read
>> + *
>> + * Return: PCIBIOS_SUCCESSFUL on success
>> + * EINVAL/PCIBIOS_DEVICE_NOT_FOUND/PCIBIOS_BAD_REGISTER_NUMBER
>> + * on failure.
>> + */
>> +static int xilinx_pcie_read_config(struct pci_bus *bus,
>> + unsigned int devfn, int where,
>> + int size, u32 *val)
>> +{
>> + struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
>> + void __iomem *addr;
>> +
>> + if (!port) {
>> + BUG();
>> + return -EINVAL;
>> + }
>
> I don't think you need to test "port" for NULL here. And I don't
> think callers will be prepared for -EINVAL anyway; they'll be
> expecting PCIBIOS_* values.
Ok, I will fix in all the suggested places.
>
>> + if (xilinx_pcie_verify_config(bus, devfn)) {
>> + *val = 0xFFFFFFFF;
>> + return PCIBIOS_DEVICE_NOT_FOUND;
>> + }
<snip>
>> + */
>> +static void xilinx_pcie_add_bus(struct pci_bus *bus)
>> +{
>> + if (IS_ENABLED(CONFIG_PCI_MSI)) {
>
> Did you verify that this builds with both CONFIG_PCI_MSI=y and with it
> unset?
Yes, I have tested.
< snip >
>> +{
>> + port->link_up = xilinx_pcie_is_link_up(port);
>> + if (!port->link_up)
>
> I'd use "if (port->link_up)" and reorder the dev_info() to avoid the
> negation (trivial, I know, but why use the negative when the positive
> works just as well?)
Ok.
>
>> + dev_info(port->dev, "PCIe Link is DOWN\n");
>> + else
>> + dev_info(port->dev, "PCIe Link is UP\n");
>> +
>> + /* Disable all interrupts*/
>> + pcie_write(port, ~XILINX_PCIE_IDR_ALL_MASK,
>> + XILINX_PCIE_REG_IMR);
>> +
>> + /* Clear pending interrupts */
>> + pcie_write(port, pcie_read(port, XILINX_PCIE_REG_IDR) &
>> + XILINX_PCIE_IMR_ALL_MASK,
>> + XILINX_PCIE_REG_IDR);
>> +
>> + /* Enable all interrupts*/
>
> Missing space before "*/" (also on "Disable all interrupts" comment).
Ok.
>
>> + pcie_write(port, XILINX_PCIE_IMR_ALL_MASK, XILINX_PCIE_REG_IMR);
>> +
>> + /* Enable the Bridge enable bit */
>> + pcie_write(port, pcie_read(port, XILINX_PCIE_REG_RPSC) |
>> + XILINX_PCIE_REG_RPSC_BEN,
>> + XILINX_PCIE_REG_RPSC);
>> +}
>> +
>> +/**
>> + * xilinx_pcie_setup - Setup memory resources
>> + * @nr: Bus number
>> + * @sys: Per controller structure
>> + *
>> + * Return: '1' on success and error value on failure
>
> Incorrect. No point in a comment that explains obvious code anyway.
> But maybe DocBook requires it, and I guess it's OK then.
>
Ok.
>> + */
>> +static int xilinx_pcie_setup(int nr, struct pci_sys_data *sys)
>> +{
>> + struct xilinx_pcie_port *port = sys_to_pcie(sys);
>> +
>> + list_splice_init(&port->resources, &sys->resources);
>> +
>> + return 1;
>> +}
>> +
>> +/**
>> + * xilinx_pcie_scan_bus - Scan PCIe bus for devices
>> + * @nr: Bus number
>> + * @sys: Per controller structure
>> + *
>> + * Return: Valid Bus pointer on success and NULL on failure
>> + */
>> +static struct pci_bus __init *xilinx_pcie_scan_bus(int nr,
>> + struct pci_sys_data *sys)
>> +{
>> + struct xilinx_pcie_port *port = sys_to_pcie(sys);
>> + struct pci_bus *bus;
>> +
>> + if (port) {
>
> I think this test (and the BUG()) is superfluous. I don't think it's
> possible to get here with sys->private_data == NULL. And if we do,
> we'll take a null pointer fault and get a nice backtrace anyway.
Ok.
>
>> + port->root_busno = sys->busnr;
>> + bus = pci_scan_root_bus(port->dev, sys->busnr, &xilinx_pcie_ops,
>> + sys, &sys->resources);
>> + } else {
>> + bus = NULL;
>> + BUG();
>> + }
< snip >
>> +MODULE_AUTHOR("Xilinx Inc");
>> +MODULE_DESCRIPTION("Xilinx AXI PCIe driver");
>> +MODULE_LICENSE("GPLv2");
>
> I think you want "GPL v2" here (with the space; see
> license_is_gpl_compatible()).
I will fix them in my v5.
Thanks for the review,
Srikanth.
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
More information about the linux-arm-kernel
mailing list