[PATCH v5 2/2] can: m_can: add Bosch M_CAN controller support

[Varka Bhadram]

On 07/16/2014 03:00 PM, Dong Aisheng wrote:
> The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
> For TX, only one dedicated tx buffer is used for sending data.
> For RX, RXFIFO 0 is used for receiving data to avoid overflow.
> Rx FIFO 1 and Rx Buffers are not used currently, as well as Tx Event FIFO.
>
> Due to the message ram can be shared by multi m_can instances
> and the fifo element is configurable which is SoC dependant,
> the design is to parse the message ram related configuration data from device
> tree rather than hardcode define it in driver which can make the message
> ram sharing fully transparent to M_CAN controller driver,
> then we can gain better driver maintainability and future features upgrade.
>
> M_CAN also supports CANFD protocol features like data payload up to 64 bytes
> and bitrate switch at runtime, however, this patch still does not add the
> support for these features.
>
> Cc: Wolfgang Grandegger <wg at grandegger.com>
> Cc: Marc Kleine-Budde <mkl at pengutronix.de>
> Cc: Mark Rutland <mark.rutland at arm.com>
> Cc: Oliver Hartkopp <socketcan at hartkopp.net>
> Cc: Varka Bhadram <varkabhadram at gmail.com>
> Signed-off-by: Dong Aisheng <b29396 at freescale.com>
> ---
> changes since v4:
> some minor changes:
> - introduce m_can_fifo_write and is_lec_err functin
> - define macro M_CAN_FIFO_XXX for FIFO
> - move m_can_of_table before platform_driver
> - a few indent fix
>
> Changes since v3:
> A few minor changes:
> - use the updated name of bosch,mram-cfg
> - remove .owner = THIS_MODULE
> - add a line comment for mram_cfg structure
>
> Changes since v2:
> - fix checkpatch warnings
> - handle CAN_CTRLMODE_BERR_REPORTING properly that disable LEC error
>    interrupts (Bus error) if no CAN_CTRLMODE_BERR_REPORTING.
> - introduce struct mram_cfg array to store message ram configuration data
>    for each fifo
> - fix txb offset calculate wrong issue(should not plus mram_off again)
> - check return for clk_prepare_enable
> - split doc part into a separate patch
>
> Changes since v1:
> Addressed all comments from Mark Rutland, Hartkopp and Marc Kleine-Budde
> - merge three patches into one
> - create directory drivers/net/can/m_can
> - improve binding doc
> - make sure using valid pointer before netif_receive_skb(skb)
> - remove debug info a bit
> - let the stats are updated even if alloc_can_err_skb() fails
> - other small fixes
> ---
>   drivers/net/can/Kconfig        |    2 +
>   drivers/net/can/Makefile       |    1 +
>   drivers/net/can/m_can/Kconfig  |    4 +
>   drivers/net/can/m_can/Makefile |    7 +
>   drivers/net/can/m_can/m_can.c  | 1202 ++++++++++++++++++++++++++++++++++++++++
>   5 files changed, 1216 insertions(+), 0 deletions(-)
>   create mode 100644 drivers/net/can/m_can/Kconfig
>   create mode 100644 drivers/net/can/m_can/Makefile
>   create mode 100644 drivers/net/can/m_can/m_can.c
>
>
This series addressed all of my comments ...Thanks  :-)

Reviewed-by: Varka Bhadram <varkabhadram at gmail.com>

-- 
Regards,
Varka Bhadram.