[PATCH v4 1/2] can: m_can: add device tree binding documentation

[Marc Kleine-Budde]

On 07/14/2014 01:40 PM, Dong Aisheng wrote:
> add M_CAN device tree binding documentation
> 
> Cc: Wolfgang Grandegger <wg at grandegger.com>
> Cc: Marc Kleine-Budde <mkl at pengutronix.de>
> Cc: Mark Rutland <mark.rutland at arm.com>
> Cc: Oliver Hartkopp <socketcan at hartkopp.net>
> Cc: Varka Bhadram <varkabhadram at gmail.com>
> Signed-off-by: Dong Aisheng <b29396 at freescale.com>
> ---
> 
> Changes since v3:
> - change mram-cfg property name to bosch,mram-cfg
> - indent change
> ---
>  .../devicetree/bindings/net/can/m_can.txt          |   67 ++++++++++++++++++++
>  1 files changed, 67 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/net/can/m_can.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/can/m_can.txt b/Documentation/devicetree/bindings/net/can/m_can.txt
> new file mode 100644
> index 0000000..5cff839
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/can/m_can.txt
> @@ -0,0 +1,67 @@
> +Bosch MCAN controller Device Tree Bindings
> +-------------------------------------------------
> +
> +Required properties:
> +- compatible		: Should be "bosch,m_can" for M_CAN controllers
> +- reg			: physical base address and size of the M_CAN
> +			  registers map and Message RAM
> +- reg-names		: Should be "m_can" and "message_ram"
> +- interrupts		: Should be the interrupt number of M_CAN interrupt
> +			  line 0 and line 1, could be same if sharing
> +			  the same interrupt.
> +- interrupt-names	: Should contain "int0" and "int1"
> +- clocks		: Clocks used by controller, should be host clock
> +			  and CAN clock.
> +- clock-names		: Should contain "hclk" and "cclk"
> +- pinctrl-<n>		: Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
> +- pinctrl-names 	: Names corresponding to the numbered pinctrl states
> +- bosch,mram-cfg	: Message RAM configuration data.
> +			  Multiple M_CAN instances can share the same Message
> +			  RAM and each element(e.g Rx FIFO or Tx Buffer and etc)
> +			  number in Message RAM is also configurable,
> +			  so this property is telling driver how the shared or
> +			  private Message RAM are used by this M_CAN controller.
> +
> +			  The format should be as follows:
> +			  <offset sidf_elems xidf_elems rxf0_elems rxf1_elems
> +			   rxb_elems txe_elems txb_elems>
> +			  The 'offset' is an address offset of the Message RAM
> +			  where the following elements start from. This is
> +			  usually set to 0x0 if you're using a private Message
> +			  RAM. The remain cells are used to specify how many
> +			  elements are used for each FIFO/Buffer.
> +
> +			  M_CAN includes the following elements according to user manual:
> +			  11-bit Filter	0-128 elements / 0-128 words
> +			  29-bit Filter	0-64 elements / 0-128 words
> +			  Rx FIFO 0	0-64 elements / 0-1152 words
> +			  Rx FIFO 1	0-64 elements / 0-1152 words
> +			  Rx Buffers	0-64 elements / 0-1152 words
> +			  Tx Event FIFO	0-32 elements / 0-64 words
> +			  Tx Buffers	0-32 elements / 0-576 words
> +
> +			  Please refer to 2.4.1 Message RAM Configuration in
> +			  Bosch M_CAN user manual for details.
> +
> +Example:
> +SoC dtsi:
> +m_can1: can at 020e8000 {
> +	compatible = "bosch,m_can";
> +	reg = <0x020e8000 0x4000>, <0x02298000 0x4000>;
> +	reg-names = "m_can", "message_ram";
> +	interrupts = <0 114 0x04>,
> +		     <0 114 0x04>;
> +	interrupt-names = "int0", "int1";
> +	clocks = <&clks IMX6SX_CLK_CANFD>,
> +		 <&clks IMX6SX_CLK_CANFD>;
> +	clock-names = "hclk", "cclk";
> +	bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>;
> +	status = "disabled";
> +};
> +
> +Board dtsi:
         ^^^^

The board is typically a dts, isn't it?

> +&m_can1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_m_can1>;
> +	status = "enabled";
> +};
> 
Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140714/3339d7c9/attachment-0001.sig>