[PATCH 3/3] pinctrl: Introduce pinctrl driver for Qualcomm pm8xxx
Bjorn Andersson
bjorn.andersson at sonymobile.com
Mon Jul 7 18:26:25 PDT 2014
This introduces a pinctrl, pinconf, pinmux and gpio driver for the gpio
block found in pm8018, pm8038, pm8058, pm8917 and pm8921 pmics from
Qualcomm.
Signed-off-by: Bjorn Andersson <bjorn.andersson at sonymobile.com>
---
drivers/pinctrl/Kconfig | 11 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-pm8xxx-gpio.c | 796 +++++++++++++++++++++++++++++++++
3 files changed, 808 insertions(+)
create mode 100644 drivers/pinctrl/pinctrl-pm8xxx-gpio.c
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 0042ccb..c173db6 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -278,6 +278,17 @@ config PINCTRL_DB8540
bool "DB8540 pin controller driver"
depends on PINCTRL_NOMADIK && ARCH_U8500
+config PINCTRL_PM8XXX_GPIO
+ tristate "Qualcomm PM8xxx gpio driver"
+ depends on GPIOLIB && OF && (ARCH_QCOM || COMPILE_TEST)
+ select PINCONF
+ select PINMUX
+ select GENERIC_PINCONF
+ help
+ This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+ Qualcomm GPIO blocks found in the pm8018, pm8038, pm8058, pm8917 and
+ pm8921 pmics from Qualcomm.
+
config PINCTRL_ROCKCHIP
bool
select PINMUX
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index c4b5d40..806f6ad 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -47,6 +47,7 @@ obj-$(CONFIG_PINCTRL_STN8815) += pinctrl-nomadik-stn8815.o
obj-$(CONFIG_PINCTRL_DB8500) += pinctrl-nomadik-db8500.o
obj-$(CONFIG_PINCTRL_DB8540) += pinctrl-nomadik-db8540.o
obj-$(CONFIG_PINCTRL_PALMAS) += pinctrl-palmas.o
+obj-$(CONFIG_PINCTRL_PM8XXX_GPIO) += pinctrl-pm8xxx-gpio.o
obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o
obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o
obj-$(CONFIG_PINCTRL_SIRF) += sirf/
diff --git a/drivers/pinctrl/pinctrl-pm8xxx-gpio.c b/drivers/pinctrl/pinctrl-pm8xxx-gpio.c
new file mode 100644
index 0000000..5aaf914
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-pm8xxx-gpio.c
@@ -0,0 +1,796 @@
+/*
+ * Copyright (c) 2014, Sony Mobile Communications AB.
+ * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/slab.h>
+#include <linux/regmap.h>
+#include <linux/gpio.h>
+#include <linux/mfd/pm8921-core.h>
+
+#include <dt-bindings/pinctrl/qcom,pm8xxx-gpio.h>
+
+#include "core.h"
+#include "pinconf.h"
+#include "pinctrl-utils.h"
+
+/* direction */
+#define PM8XXX_GPIO_DIR_OUT BIT(0)
+#define PM8XXX_GPIO_DIR_IN BIT(1)
+
+/* output buffer */
+#define PM8XXX_GPIO_PUSH_PULL 0
+#define PM8XXX_GPIO_OPEN_DRAIN 1
+
+/* bias */
+#define PM8XXX_GPIO_BIAS_PU_30 0
+#define PM8XXX_GPIO_BIAS_PU_1P5 1
+#define PM8XXX_GPIO_BIAS_PU_31P5 2
+#define PM8XXX_GPIO_BIAS_PU_1P5_30 3
+#define PM8XXX_GPIO_BIAS_PD 4
+#define PM8XXX_GPIO_BIAS_NP 5
+
+/* GPIO registers */
+#define SSBI_REG_ADDR_GPIO_BASE 0x150
+#define SSBI_REG_ADDR_GPIO(n) (SSBI_REG_ADDR_GPIO_BASE + n)
+
+#define PM8XXX_GPIO_WRITE BIT(7)
+
+#define PM8XXX_MAX_GPIOS 44
+
+struct pm8xxx_gpio_pin {
+ int irq;
+
+ u8 power_source;
+ u8 direction;
+ u8 output_buffer;
+ u8 output_value;
+ u8 bias;
+ u8 output_strength;
+ u8 disable;
+ u8 function;
+ u8 non_inverted;
+};
+
+struct pm8xxx_gpio_data {
+ int ngpio;
+ const int *power_sources;
+ int npower_sources;
+};
+
+struct pm8xxx_gpio {
+ struct device *dev;
+ struct regmap *regmap;
+ struct pinctrl_dev *pctrl;
+ struct gpio_chip chip;
+
+ const struct pm8xxx_gpio_data *data;
+
+ struct pm8xxx_gpio_pin pins[PM8XXX_MAX_GPIOS];
+};
+
+static const char * const pm8xxx_gpio_groups[PM8XXX_MAX_GPIOS] = {
+ "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8",
+ "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15",
+ "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22",
+ "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29",
+ "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42", "gpio43",
+ "gpio44",
+};
+
+static const char * const pm8xxx_gpio_functions[] = {
+ "normal", "paired",
+ "func1", "func2",
+ "dtest1", "dtest2", "dtest3", "dtest4",
+};
+
+static int pm8xxx_gpio_read(struct pm8xxx_gpio *pctrl, int pin, int bank)
+{
+ int reg = SSBI_REG_ADDR_GPIO(pin);
+ unsigned int val = bank << 4;
+ int ret;
+
+ ret = regmap_write(pctrl->regmap, reg, val);
+ if (ret) {
+ dev_err(pctrl->dev,
+ "failed to select bank %d of pin %d\n", bank, pin);
+ return ret;
+ }
+
+ ret = regmap_read(pctrl->regmap, reg, &val);
+ if (ret) {
+ dev_err(pctrl->dev,
+ "failed to read register %d of pin %d\n", bank, pin);
+ return ret;
+ }
+
+ return val;
+}
+
+static int pm8xxx_gpio_write(struct pm8xxx_gpio *pctrl,
+ int pin, int bank, u8 val)
+{
+ int ret;
+
+ val |= PM8XXX_GPIO_WRITE;
+ val |= bank << 4;
+
+ ret = regmap_write(pctrl->regmap, SSBI_REG_ADDR_GPIO(pin), val);
+ if (ret)
+ dev_err(pctrl->dev, "failed to write register\n");
+
+ return ret;
+}
+
+static int pm8xxx_gpio_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ return pctrl->data->ngpio;
+}
+
+static const char *pm8xxx_gpio_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned group)
+{
+ return pm8xxx_gpio_groups[group];
+}
+
+static const struct pinctrl_ops pm8xxx_gpio_pinctrl_ops = {
+ .get_groups_count = pm8xxx_gpio_get_groups_count,
+ .get_group_name = pm8xxx_gpio_get_group_name,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_group,
+ .dt_free_map = pinctrl_utils_dt_free_map,
+};
+
+static int pm8xxx_get_functions_count(struct pinctrl_dev *pctldev)
+{
+ return ARRAY_SIZE(pm8xxx_gpio_functions);
+}
+
+static const char *pm8xxx_get_function_name(struct pinctrl_dev *pctldev,
+ unsigned function)
+{
+ return pm8xxx_gpio_functions[function];
+}
+
+static int pm8xxx_get_function_groups(struct pinctrl_dev *pctldev,
+ unsigned function,
+ const char * const **groups,
+ unsigned * const num_groups)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = pm8xxx_gpio_groups;
+ *num_groups = pctrl->data->ngpio;
+ return 0;
+}
+
+static int pm8xxx_pinmux_enable(struct pinctrl_dev *pctldev,
+ unsigned function,
+ unsigned group)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[group];
+ u8 val;
+
+ pin->function = function;
+ val = pin->function << 1;
+
+ pm8xxx_gpio_write(pctrl, group, 4, val);
+
+ return 0;
+}
+
+static void pm8xxx_pinmux_disable(struct pinctrl_dev *pctldev,
+ unsigned function,
+ unsigned group)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[group];
+ u8 val;
+
+ pin->function = 0;
+ val = pin->function << 1;
+
+ pm8xxx_gpio_write(pctrl, group, 4, val);
+}
+
+static const struct pinmux_ops pm8xxx_pinmux_ops = {
+ .get_functions_count = pm8xxx_get_functions_count,
+ .get_function_name = pm8xxx_get_function_name,
+ .get_function_groups = pm8xxx_get_function_groups,
+ .enable = pm8xxx_pinmux_enable,
+ .disable = pm8xxx_pinmux_disable,
+};
+
+static int pm8xxx_gpio_config_get(struct pinctrl_dev *pctldev,
+ unsigned int offset,
+ unsigned long *config)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset];
+ unsigned param = pinconf_to_config_param(*config);
+ unsigned arg;
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ arg = pin->bias == PM8XXX_GPIO_BIAS_NP;
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ arg = pin->bias == PM8XXX_GPIO_BIAS_PD;
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (pin->bias >= PM8XXX_GPIO_BIAS_PU_30 &&
+ pin->bias <= PM8XXX_GPIO_BIAS_PU_1P5_30)
+ arg = PM8XXX_GPIO_PULL_UP_30 + pin->bias;
+ else
+ arg = 0;
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ arg = pin->disable;
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ arg = pin->direction == PM8XXX_GPIO_DIR_IN;
+ break;
+ case PIN_CONFIG_OUTPUT:
+ arg = pin->output_value;
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ arg = pin->power_source;
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ arg = pin->output_strength;
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ arg = pin->output_buffer == PM8XXX_GPIO_PUSH_PULL;
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ arg = pin->output_buffer == PM8XXX_GPIO_OPEN_DRAIN;
+ break;
+ default:
+ dev_err(pctrl->dev,
+ "unsupported config parameter: %x\n",
+ param);
+ return -EINVAL;
+ }
+
+ *config = pinconf_to_config_packed(param, arg);
+
+ return 0;
+}
+
+static int resolve_power_source(struct pm8xxx_gpio *pctrl, unsigned arg)
+{
+ const struct pm8xxx_gpio_data *data = pctrl->data;
+ int i;
+
+ for (i = 0; i < data->npower_sources; i++) {
+ if (data->power_sources[i] == arg)
+ return i;
+ }
+
+ dev_err(pctrl->dev, "invalid power source\n");
+ return -EINVAL;
+}
+
+static int pm8xxx_gpio_config_set(struct pinctrl_dev *pctldev,
+ unsigned int offset,
+ unsigned long *configs,
+ unsigned num_configs)
+{
+ struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset];
+ unsigned param;
+ unsigned arg;
+ unsigned i;
+ int ret;
+ u8 banks = 0;
+ u8 val;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ pin->bias = PM8XXX_GPIO_BIAS_NP;
+ banks |= BIT(2);
+ pin->disable = 0;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ pin->bias = PM8XXX_GPIO_BIAS_PD;
+ banks |= BIT(2);
+ pin->disable = 0;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (arg < PM8XXX_GPIO_PULL_UP_30 ||
+ arg > PM8XXX_GPIO_PULL_UP_1P5_30) {
+ dev_err(pctrl->dev, "invalid pull-up level\n");
+ return -EINVAL;
+ }
+ pin->bias = arg - PM8XXX_GPIO_BIAS_PU_30;
+ banks |= BIT(2);
+ pin->disable = 0;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+ pin->disable = 1;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ pin->direction = PM8XXX_GPIO_DIR_IN;
+ banks |= BIT(1);
+ break;
+ case PIN_CONFIG_OUTPUT:
+ pin->direction = PM8XXX_GPIO_DIR_OUT;
+ pin->output_value = !!arg;
+ banks |= BIT(1);
+ break;
+ case PIN_CONFIG_POWER_SOURCE:
+ /* Sanity check the power source */
+ ret = resolve_power_source(pctrl, arg);
+ if (ret < 0)
+ return ret;
+ pin->power_source = arg;
+ banks |= BIT(0);
+ break;
+ case PIN_CONFIG_DRIVE_STRENGTH:
+ if (arg > PM8XXX_GPIO_STRENGTH_LOW) {
+ dev_err(pctrl->dev, "invalid drive strength\n");
+ return -EINVAL;
+ }
+ pin->output_strength = arg;
+ banks |= BIT(3);
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ pin->output_buffer = PM8XXX_GPIO_PUSH_PULL;
+ banks |= BIT(1);
+ break;
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ pin->output_buffer = PM8XXX_GPIO_OPEN_DRAIN;
+ banks |= BIT(1);
+ break;
+ default:
+ dev_err(pctrl->dev,
+ "unsupported config parameter: %x\n",
+ param);
+ return -EINVAL;
+ }
+ }
+
+ if (banks & BIT(0)) {
+ ret = resolve_power_source(pctrl, pin->power_source);
+ pm8xxx_gpio_write(pctrl, offset, 0, ret << 1);
+ }
+
+ if (banks & BIT(1)) {
+ val = pin->direction << 2;
+ val |= pin->output_buffer << 1;
+ val |= pin->output_value;
+ pm8xxx_gpio_write(pctrl, offset, 1, val);
+ }
+
+ if (banks & BIT(2)) {
+ val = pin->bias << 1;
+ pm8xxx_gpio_write(pctrl, offset, 2, val);
+ }
+
+ if (banks & BIT(3)) {
+ val = pin->output_strength << 2;
+ val |= pin->disable;
+ pm8xxx_gpio_write(pctrl, offset, 3, val);
+ }
+
+ if (banks & BIT(4)) {
+ val = pin->function << 1;
+ pm8xxx_gpio_write(pctrl, offset, 4, val);
+ }
+
+ if (banks & BIT(5)) {
+ val = 0;
+ if (pin->non_inverted)
+ val |= BIT(3);
+ pm8xxx_gpio_write(pctrl, offset, 5, val);
+ }
+
+ return 0;
+}
+
+static const struct pinconf_ops pm8xxx_gpio_pinconf_ops = {
+ .pin_config_group_get = pm8xxx_gpio_config_get,
+ .pin_config_group_set = pm8xxx_gpio_config_set,
+};
+
+static struct pinctrl_desc pm8xxx_gpio_desc = {
+ .pctlops = &pm8xxx_gpio_pinctrl_ops,
+ .pmxops = &pm8xxx_pinmux_ops,
+ .confops = &pm8xxx_gpio_pinconf_ops,
+ .owner = THIS_MODULE,
+};
+
+static int pm8xxx_gpio_direction_input(struct gpio_chip *chip,
+ unsigned offset)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset - 1];
+ u8 val;
+
+ pin->direction = PM8XXX_GPIO_DIR_IN;
+ val = pin->direction << 2;
+
+ pm8xxx_gpio_write(pctrl, offset, 1, val);
+
+ return 0;
+}
+
+static int pm8xxx_gpio_direction_output(struct gpio_chip *chip,
+ unsigned offset,
+ int value)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset - 1];
+ u8 val;
+
+ pin->direction = PM8XXX_GPIO_DIR_OUT;
+ pin->output_value = !!value;
+
+ val = pin->direction << 2;
+ val |= pin->output_buffer << 1;
+ val |= pin->output_value;
+
+ pm8xxx_gpio_write(pctrl, offset, 1, val);
+
+ return 0;
+}
+
+static int pm8xxx_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset - 1];
+
+ if (pin->direction == PM8XXX_GPIO_DIR_OUT)
+ return pin->output_value;
+ else
+ return pm8xxx_read_irq_status(pin->irq);
+}
+
+static void pm8xxx_gpio_set(struct gpio_chip *gc, unsigned offset, int value)
+{
+ struct pm8xxx_gpio *pctrl = container_of(gc, struct pm8xxx_gpio, chip);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset - 1];
+ u8 val;
+
+ pin->output_value = !!value;
+
+ val = pin->direction << 2;
+ val |= pin->output_buffer << 1;
+ val |= pin->output_value;
+
+ pm8xxx_gpio_write(pctrl, offset, 1, val);
+}
+
+static int pm8xxx_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset - 1];
+
+ return pin->irq;
+}
+
+#ifdef CONFIG_DEBUG_FS
+#include <linux/seq_file.h>
+
+static void pm8xxx_gpio_dbg_show_one(struct seq_file *s,
+ struct pinctrl_dev *pctldev,
+ struct gpio_chip *chip,
+ unsigned offset,
+ unsigned gpio)
+{
+ struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip);
+ struct pm8xxx_gpio_pin *pin = &pctrl->pins[offset];
+
+ static const char * const directions[] = {
+ "off", "out", "in", "both"
+ };
+ static const char * const sources[] = {
+ "bb", "l2", "l3", "l4", "l5", "l6", "l7", "l8", "l11",
+ "l14", "l15", "l17", "s3", "s4", "vph"
+ };
+ static const char * const biases[] = {
+ "pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA",
+ "pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull"
+ };
+ static const char * const buffer_types[] = {
+ "push-pull", "open-drain"
+ };
+ static const char * const strengths[] = {
+ "no", "high", "medium", "low"
+ };
+
+ seq_printf(s, " gpio%-2d:", offset + 1);
+ if (pin->disable) {
+ seq_puts(s, " ---");
+ } else {
+ seq_printf(s, " %-4s", directions[pin->direction]);
+ seq_printf(s, " %-7s", pm8xxx_gpio_functions[pin->function]);
+ seq_printf(s, " %-3s", sources[pin->power_source]);
+ seq_printf(s, " %-27s", biases[pin->bias]);
+ seq_printf(s, " %-10s", buffer_types[pin->output_buffer]);
+ seq_printf(s, " %-4s", pin->output_value ? "high" : "low");
+ seq_printf(s, " %-7s", strengths[pin->output_strength]);
+ if (!pin->non_inverted)
+ seq_puts(s, " inverted");
+ }
+}
+
+static void pm8xxx_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ unsigned gpio = chip->base;
+ unsigned i;
+
+ for (i = 0; i < chip->ngpio; i++, gpio++) {
+ pm8xxx_gpio_dbg_show_one(s, NULL, chip, i, gpio);
+ seq_puts(s, "\n");
+ }
+}
+
+#else
+#define msm_gpio_dbg_show NULL
+#endif
+
+static struct gpio_chip pm8xxx_gpio_template = {
+ .direction_input = pm8xxx_gpio_direction_input,
+ .direction_output = pm8xxx_gpio_direction_output,
+ .get = pm8xxx_gpio_get,
+ .set = pm8xxx_gpio_set,
+ .to_irq = pm8xxx_gpio_to_irq,
+ .dbg_show = pm8xxx_gpio_dbg_show,
+ .owner = THIS_MODULE,
+};
+
+static int pm8xxx_gpio_populate(struct pm8xxx_gpio *pctrl)
+{
+ const struct pm8xxx_gpio_data *data = pctrl->data;
+ struct pm8xxx_gpio_pin *pin;
+ int val;
+ int i;
+
+ for (i = 0; i < pctrl->data->ngpio; i++) {
+ pin = &pctrl->pins[i];
+
+ val = pm8xxx_gpio_read(pctrl, i, 0);
+ if (val < 0)
+ return val;
+
+ pin->power_source = data->power_sources[(val >> 1) & 0x7];
+
+ val = pm8xxx_gpio_read(pctrl, i, 1);
+ if (val < 0)
+ return val;
+
+ pin->direction = (val >> 2) & 0x3;
+ pin->output_buffer = !!(val & BIT(1));
+ pin->output_value = val & BIT(0);
+
+ val = pm8xxx_gpio_read(pctrl, i, 2);
+ if (val < 0)
+ return val;
+
+ pin->bias = (val >> 1) & 0x7;
+
+ val = pm8xxx_gpio_read(pctrl, i, 3);
+ if (val < 0)
+ return val;
+
+ pin->output_strength = (val >> 2) & 0x3;
+ pin->disable = val & BIT(0);
+
+ val = pm8xxx_gpio_read(pctrl, i, 4);
+ if (val < 0)
+ return val;
+
+ pin->function = (val >> 1) & 0x7;
+
+ val = pm8xxx_gpio_read(pctrl, i, 5);
+ if (val < 0)
+ return val;
+
+ pin->non_inverted = !!(val & BIT(3));
+ }
+
+ return 0;
+}
+
+static const struct pm8xxx_gpio_data pm8018_gpio_data = {
+ .ngpio = 6,
+ .power_sources = (int[]) {
+ PM8XXX_GPIO_VIN_L4, PM8XXX_GPIO_VIN_L14, PM8XXX_GPIO_VIN_S3,
+ PM8XXX_GPIO_VIN_L6, PM8XXX_GPIO_VIN_L2, PM8XXX_GPIO_VIN_L5,
+ PM8XXX_GPIO_VIN_L8, PM8XXX_GPIO_VIN_VPH
+ },
+ .npower_sources = 8,
+};
+
+static const struct pm8xxx_gpio_data pm8038_gpio_data = {
+ .ngpio = 12,
+ .power_sources = (int[]) {
+ PM8XXX_GPIO_VIN_VPH, PM8XXX_GPIO_VIN_BB, PM8XXX_GPIO_VIN_L11,
+ PM8XXX_GPIO_VIN_L15, PM8XXX_GPIO_VIN_L4, PM8XXX_GPIO_VIN_L3,
+ PM8XXX_GPIO_VIN_L17
+ },
+ .npower_sources = 7,
+};
+
+static const struct pm8xxx_gpio_data pm8058_gpio_data = {
+ .ngpio = 40,
+ .power_sources = (int[]) {
+ PM8XXX_GPIO_VIN_VPH, PM8XXX_GPIO_VIN_BB, PM8XXX_GPIO_VIN_S3,
+ PM8XXX_GPIO_VIN_L3, PM8XXX_GPIO_VIN_L7, PM8XXX_GPIO_VIN_L6,
+ PM8XXX_GPIO_VIN_L5, PM8XXX_GPIO_VIN_L2
+ },
+ .npower_sources = 8,
+};
+static const struct pm8xxx_gpio_data pm8917_gpio_data = {
+ .ngpio = 38,
+ .power_sources = (int[]) {
+ PM8XXX_GPIO_VIN_VPH, PM8XXX_GPIO_VIN_BB, PM8XXX_GPIO_VIN_S4,
+ PM8XXX_GPIO_VIN_L15, PM8XXX_GPIO_VIN_L4, PM8XXX_GPIO_VIN_L3,
+ PM8XXX_GPIO_VIN_L17
+ },
+ .npower_sources = 7,
+};
+
+static const struct pm8xxx_gpio_data pm8921_gpio_data = {
+ .ngpio = 44,
+ .power_sources = (int[]) {
+ PM8XXX_GPIO_VIN_VPH, PM8XXX_GPIO_VIN_BB, PM8XXX_GPIO_VIN_S4,
+ PM8XXX_GPIO_VIN_L15, PM8XXX_GPIO_VIN_L4, PM8XXX_GPIO_VIN_L3,
+ PM8XXX_GPIO_VIN_L17
+ },
+ .npower_sources = 7,
+};
+
+static const struct of_device_id pm8xxx_gpio_of_match[] = {
+ { .compatible = "qcom,pm8018-gpio", .data = &pm8018_gpio_data },
+ { .compatible = "qcom,pm8038-gpio", .data = &pm8038_gpio_data },
+ { .compatible = "qcom,pm8058-gpio", .data = &pm8058_gpio_data },
+ { .compatible = "qcom,pm8917-gpio", .data = &pm8917_gpio_data },
+ { .compatible = "qcom,pm8921-gpio", .data = &pm8921_gpio_data },
+ { },
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_gpio_of_match);
+
+static int pm8xxx_gpio_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *match;
+ struct pm8xxx_gpio *pctrl;
+ int ret;
+ int i;
+
+ match = of_match_node(pm8xxx_gpio_of_match, pdev->dev.of_node);
+ if (!match)
+ return -ENXIO;
+
+ pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL);
+ if (!pctrl)
+ return -ENOMEM;
+
+ pctrl->dev = &pdev->dev;
+ pctrl->data = match->data;
+
+ BUG_ON(pctrl->data->ngpio > PM8XXX_MAX_GPIOS);
+
+ pctrl->chip = pm8xxx_gpio_template;
+ pctrl->chip.base = -1;
+ pctrl->chip.dev = &pdev->dev;
+ pctrl->chip.of_node = pdev->dev.of_node;
+ pctrl->chip.label = dev_name(pctrl->dev);
+ pctrl->chip.ngpio = pctrl->data->ngpio;
+
+ pctrl->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!pctrl->regmap) {
+ dev_err(&pdev->dev, "parent regmap unavailable\n");
+ return -ENXIO;
+ }
+
+ for (i = 0; i < pctrl->data->ngpio; i++) {
+ ret = platform_get_irq(pdev, i);
+ if (ret < 0) {
+ dev_err(&pdev->dev,
+ "missing interrupts for pin %d\n", i);
+ return ret;
+ }
+
+ pctrl->pins[i].irq = ret;
+ }
+
+ ret = pm8xxx_gpio_populate(pctrl);
+ if (ret)
+ return ret;
+
+ pm8xxx_gpio_desc.name = dev_name(&pdev->dev);
+ pctrl->pctrl = pinctrl_register(&pm8xxx_gpio_desc, &pdev->dev, pctrl);
+ if (!pctrl->pctrl) {
+ dev_err(&pdev->dev, "couldn't register pm8xxx gpio driver\n");
+ return -ENODEV;
+ }
+
+ ret = gpiochip_add(&pctrl->chip);
+ if (ret) {
+ dev_err(&pdev->dev, "failed register gpiochip\n");
+ goto unregister_pinctrl;
+ }
+
+ ret = gpiochip_add_pin_range(&pctrl->chip,
+ dev_name(pctrl->dev),
+ 1, 0, pctrl->data->ngpio);
+ if (ret) {
+ dev_err(pctrl->dev, "failed to add pin range\n");
+ goto unregister_gpiochip;
+ }
+
+ platform_set_drvdata(pdev, pctrl);
+
+ dev_dbg(&pdev->dev, "Qualcomm pm8xxx gpio driver probed\n");
+
+ return 0;
+
+unregister_pinctrl:
+ pinctrl_unregister(pctrl->pctrl);
+
+unregister_gpiochip:
+ if (gpiochip_remove(&pctrl->chip))
+ dev_err(&pdev->dev, "unable to unregister gpiochip\n");
+
+ return ret;
+}
+
+static int pm8xxx_gpio_remove(struct platform_device *pdev)
+{
+ struct pm8xxx_gpio *pctrl = platform_get_drvdata(pdev);
+ int ret;
+
+ ret = gpiochip_remove(&pctrl->chip);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to remove gpiochip\n");
+ return ret;
+ }
+
+ pinctrl_unregister(pctrl->pctrl);
+
+ return 0;
+}
+
+static struct platform_driver pm8xxx_gpio_driver = {
+ .driver = {
+ .name = "pm8xxx_gpio",
+ .owner = THIS_MODULE,
+ .of_match_table = pm8xxx_gpio_of_match,
+ },
+ .probe = pm8xxx_gpio_probe,
+ .remove = pm8xxx_gpio_remove,
+};
+
+module_platform_driver(pm8xxx_gpio_driver);
+
+MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson at sonymobile.com>");
+MODULE_DESCRIPTION("Qualcomm PM8xxx GPIO driver");
+MODULE_LICENSE("GPL v2");
--
1.7.9.5
More information about the linux-arm-kernel
mailing list