[PATCH 1/3] drivers: reset: stih407: Add softreset, powerdown and picophy controllers
Peter Griffin
peter.griffin at linaro.org
Tue Jul 1 07:30:45 PDT 2014
This patch adds a softreset, powerdown and picophy reset controllers for
the STiH407 SoC.
With this patch three new devices are registered: -
1. st,stih407-powerdown
2. st,stih407-softreset
3. st,stih407-picophyreset
All three devices use system configuration registers mapped via regmap to
perform the reset or powerdown. The powerdown controller also has
an acknowledgement.
A separate picophy reset controller manages the different reset channels within
the picophy, which have a different polarity to the other system softresets.
Managing these different picophy softreset channels is necessary to correctly
handle resuming from CPS when USB2 devices are plugged into the USB3 port.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro at st.com>
Signed-off-by: Peter Griffin <peter.griffin at linaro.org>
---
.../bindings/reset/st,sti-picophyreset.txt | 41 ++++++
drivers/reset/sti/Kconfig | 4 +
drivers/reset/sti/Makefile | 1 +
drivers/reset/sti/reset-stih407.c | 159 +++++++++++++++++++++
.../dt-bindings/reset-controller/stih407-resets.h | 60 ++++++++
5 files changed, 265 insertions(+)
create mode 100644 Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt
create mode 100644 drivers/reset/sti/reset-stih407.c
create mode 100644 include/dt-bindings/reset-controller/stih407-resets.h
diff --git a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt
new file mode 100644
index 0000000..4c756d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt
@@ -0,0 +1,41 @@
+STMicroelectronics STi family Sysconfig Picophy SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip PicoPHY USB2 phy(s) using "softreset" control bits found in
+the STi family SoC system configuration registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to Documentation/devicetree/bindings/reset/reset.txt
+for common reset controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-softreset"
+- #reset-cells: 1, see below
+
+example:
+
+ picophyreset: picophyreset-controller {
+ #reset-cells = <1>;
+ compatible = "st,stih407-picophyreset";
+ };
+
+Specifying picophyreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the picophyreset device node and an
+index specifying which channel to use, as described in
+Documentation/devicetree/bindings/reset/reset.txt.
+
+example:
+ usb2_picophy0: usbpicophy at 0 {
+ resets = <&picophyreset STIH407_PICOPHY0_RESET>;
+ };
+
+Macro definitions for the supported reset channels can be found in:
+include/dt-bindings/reset-controller/stih407-resets.h
diff --git a/drivers/reset/sti/Kconfig b/drivers/reset/sti/Kconfig
index 88d2d03..f8c15a3 100644
--- a/drivers/reset/sti/Kconfig
+++ b/drivers/reset/sti/Kconfig
@@ -12,4 +12,8 @@ config STIH416_RESET
bool
select STI_RESET_SYSCFG
+config STIH407_RESET
+ bool
+ select STI_RESET_SYSCFG
+
endif
diff --git a/drivers/reset/sti/Makefile b/drivers/reset/sti/Makefile
index be1c976..dc85dfb 100644
--- a/drivers/reset/sti/Makefile
+++ b/drivers/reset/sti/Makefile
@@ -2,3 +2,4 @@ obj-$(CONFIG_STI_RESET_SYSCFG) += reset-syscfg.o
obj-$(CONFIG_STIH415_RESET) += reset-stih415.o
obj-$(CONFIG_STIH416_RESET) += reset-stih416.o
+obj-$(CONFIG_STIH407_RESET) += reset-stih407.o
diff --git a/drivers/reset/sti/reset-stih407.c b/drivers/reset/sti/reset-stih407.c
new file mode 100644
index 0000000..1650792
--- /dev/null
+++ b/drivers/reset/sti/reset-stih407.c
@@ -0,0 +1,159 @@
+/*
+ * Copyright (C) 2013 STMicroelectronics (R&D) Limited
+ * Author: Giuseppe Cavallaro <peppe.cavallaro at st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include <dt-bindings/reset-controller/stih407-resets.h>
+
+#include "reset-syscfg.h"
+
+/*
+ * STiH407 Peripheral powerdown definitions.
+ */
+static const char stih407_core[] = "st,stih407-core-syscfg";
+static const char stih407_sbc_reg[] = "st,stih407-sbc-reg-syscfg";
+static const char stih407_lpm[] = "st,stih407-lpm-syscfg";
+
+#define STIH407_PDN_0(_bit) \
+ _SYSCFG_RST_CH(stih407_core, SYSCFG_5000, _bit, SYSSTAT_5500, _bit)
+#define STIH407_PDN_1(_bit) \
+ _SYSCFG_RST_CH(stih407_core, SYSCFG_5001, _bit, SYSSTAT_5501, _bit)
+#define STIH407_PDN_ETH(_bit, _stat) \
+ _SYSCFG_RST_CH(stih407_sbc_reg, SYSCFG_4032, _bit, SYSSTAT_4520, _stat)
+
+/* Powerdown requests control 0 */
+#define SYSCFG_5000 0x0
+#define SYSSTAT_5500 0x7d0
+/* Powerdown requests control 1 (High Speed Links) */
+#define SYSCFG_5001 0x4
+#define SYSSTAT_5501 0x7d4
+
+/* Ethernet powerdown/status/reset */
+#define SYSCFG_4032 0x80
+#define SYSSTAT_4520 0x820
+
+#define SYSCFG_4002 0x8
+
+static const struct syscfg_reset_channel_data stih407_powerdowns[] = {
+ [STIH407_EMISS_POWERDOWN] = STIH407_PDN_0(1),
+ [STIH407_NAND_POWERDOWN] = STIH407_PDN_0(0),
+ [STIH407_USB3_POWERDOWN] = STIH407_PDN_1(6),
+ [STIH407_USB2_PORT1_POWERDOWN] = STIH407_PDN_1(5),
+ [STIH407_USB2_PORT0_POWERDOWN] = STIH407_PDN_1(4),
+ [STIH407_PCIE1_POWERDOWN] = STIH407_PDN_1(3),
+ [STIH407_PCIE0_POWERDOWN] = STIH407_PDN_1(2),
+ [STIH407_SATA1_POWERDOWN] = STIH407_PDN_1(1),
+ [STIH407_SATA0_POWERDOWN] = STIH407_PDN_1(0),
+ [STIH407_ETH1_POWERDOWN] = STIH407_PDN_ETH(0, 2),
+};
+
+/* Reset Generator control 0/1 */
+#define SYSCFG_5131 0x20c
+#define SYSCFG_5132 0x210
+
+#define LPM_SYSCFG_1 0x4 /* Softreset IRB & SBC UART */
+
+#define STIH407_SRST_CORE(_reg, _bit) \
+ _SYSCFG_RST_CH_NO_ACK(stih407_core, _reg, _bit)
+
+#define STIH407_SRST_SBC(_reg, _bit) \
+ _SYSCFG_RST_CH_NO_ACK(stih407_sbc_reg, _reg, _bit)
+
+#define STIH407_SRST_LPM(_reg, _bit) \
+ _SYSCFG_RST_CH_NO_ACK(stih407_lpm, _reg, _bit)
+
+static const struct syscfg_reset_channel_data stih407_softresets[] = {
+ [STIH407_ETH1_SOFTRESET] = STIH407_SRST_SBC(SYSCFG_4002, 4),
+ [STIH407_MMC1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 3),
+ [STIH407_USB2_PORT0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 28),
+ [STIH407_USB2_PORT1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 29),
+ [STIH407_PICOPHY_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 30),
+ [STIH407_IRB_SOFTRESET] = STIH407_SRST_LPM(LPM_SYSCFG_1, 6),
+ [STIH407_PCIE0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 6),
+ [STIH407_PCIE1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 15),
+ [STIH407_SATA0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 7),
+ [STIH407_SATA1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 16),
+ [STIH407_MIPHY0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 4),
+ [STIH407_MIPHY1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 13),
+ [STIH407_MIPHY2_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 22),
+ [STIH407_SATA0_PWR_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 5),
+ [STIH407_SATA1_PWR_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 14),
+ [STIH407_DELTA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 3),
+ [STIH407_BLITTER_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 10),
+ [STIH407_HDTVOUT_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 11),
+ [STIH407_HDQVDP_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 12),
+ [STIH407_VDP_AUX_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 14),
+ [STIH407_COMPO_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 15),
+ [STIH407_HDMI_TX_PHY_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 21),
+ [STIH407_JPEG_DEC_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 23),
+ [STIH407_VP8_DEC_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 24),
+ [STIH407_GPU_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 30),
+ [STIH407_HVA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 0),
+ [STIH407_ERAM_HVA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 1),
+ [STIH407_LPM_SOFTRESET] = STIH407_SRST_SBC(SYSCFG_4002, 2),
+ [STIH407_KEYSCAN_SOFTRESET] = STIH407_SRST_LPM(LPM_SYSCFG_1, 8),
+};
+
+/* PicoPHY reset/control */
+#define SYSCFG_5061 0x0f4
+
+static const struct syscfg_reset_channel_data stih407_picophyresets[] = {
+ [STIH407_PICOPHY0_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 5),
+ [STIH407_PICOPHY1_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 6),
+ [STIH407_PICOPHY2_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 7),
+};
+
+static struct syscfg_reset_controller_data stih407_powerdown_controller = {
+ .wait_for_ack = true,
+ .nr_channels = ARRAY_SIZE(stih407_powerdowns),
+ .channels = stih407_powerdowns,
+};
+
+static struct syscfg_reset_controller_data stih407_softreset_controller = {
+ .wait_for_ack = false,
+ .active_low = true,
+ .nr_channels = ARRAY_SIZE(stih407_softresets),
+ .channels = stih407_softresets,
+};
+
+static struct syscfg_reset_controller_data stih407_picophyreset_controller = {
+ .wait_for_ack = false,
+ .nr_channels = ARRAY_SIZE(stih407_picophyresets),
+ .channels = stih407_picophyresets,
+};
+
+
+static struct of_device_id stih407_reset_match[] = {
+ {.compatible = "st,stih407-powerdown",
+ .data = &stih407_powerdown_controller,},
+ {.compatible = "st,stih407-softreset",
+ .data = &stih407_softreset_controller,},
+ {.compatible = "st,stih407-picophyreset",
+ .data = &stih407_picophyreset_controller,},
+ {},
+};
+
+static struct platform_driver stih407_reset_driver = {
+ .probe = syscfg_reset_probe,
+ .driver = {
+ .name = "reset-stih407",
+ .owner = THIS_MODULE,
+ .of_match_table = stih407_reset_match,
+ },
+};
+
+static int __init stih407_reset_init(void)
+{
+ return platform_driver_register(&stih407_reset_driver);
+}
+
+arch_initcall(stih407_reset_init);
diff --git a/include/dt-bindings/reset-controller/stih407-resets.h b/include/dt-bindings/reset-controller/stih407-resets.h
new file mode 100644
index 0000000..85448a3
--- /dev/null
+++ b/include/dt-bindings/reset-controller/stih407-resets.h
@@ -0,0 +1,60 @@
+/*
+ * This header provides constants for the reset controller
+ * based peripheral powerdown requests on the STMicroelectronics
+ * STiH407 SoC.
+ */
+#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH407
+#define _DT_BINDINGS_RESET_CONTROLLER_STIH407
+
+/* Powerdown requests control 0 */
+#define STIH407_EMISS_POWERDOWN 0
+#define STIH407_NAND_POWERDOWN 1
+
+/* Synp GMAC PowerDown */
+#define STIH407_ETH1_POWERDOWN 2
+/* Powerdown requests control 1 */
+#define STIH407_USB3_POWERDOWN 3
+#define STIH407_USB2_PORT1_POWERDOWN 4
+#define STIH407_USB2_PORT0_POWERDOWN 5
+#define STIH407_PCIE1_POWERDOWN 6
+#define STIH407_PCIE0_POWERDOWN 7
+#define STIH407_SATA1_POWERDOWN 8
+#define STIH407_SATA0_POWERDOWN 9
+
+/* Reset defines */
+#define STIH407_ETH1_SOFTRESET 0
+#define STIH407_MMC1_SOFTRESET 1
+#define STIH407_PICOPHY_SOFTRESET 2
+#define STIH407_IRB_SOFTRESET 3
+#define STIH407_PCIE0_SOFTRESET 4
+#define STIH407_PCIE1_SOFTRESET 5
+#define STIH407_SATA0_SOFTRESET 6
+#define STIH407_SATA1_SOFTRESET 7
+#define STIH407_MIPHY0_SOFTRESET 8
+#define STIH407_MIPHY1_SOFTRESET 9
+#define STIH407_MIPHY2_SOFTRESET 10
+#define STIH407_SATA0_PWR_SOFTRESET 11
+#define STIH407_SATA1_PWR_SOFTRESET 12
+#define STIH407_DELTA_SOFTRESET 13
+#define STIH407_BLITTER_SOFTRESET 14
+#define STIH407_HDTVOUT_SOFTRESET 15
+#define STIH407_HDQVDP_SOFTRESET 16
+#define STIH407_VDP_AUX_SOFTRESET 17
+#define STIH407_COMPO_SOFTRESET 18
+#define STIH407_HDMI_TX_PHY_SOFTRESET 19
+#define STIH407_JPEG_DEC_SOFTRESET 20
+#define STIH407_VP8_DEC_SOFTRESET 21
+#define STIH407_GPU_SOFTRESET 22
+#define STIH407_HVA_SOFTRESET 23
+#define STIH407_ERAM_HVA_SOFTRESET 24
+#define STIH407_LPM_SOFTRESET 25
+#define STIH407_KEYSCAN_SOFTRESET 26
+#define STIH407_USB2_PORT0_SOFTRESET 27
+#define STIH407_USB2_PORT1_SOFTRESET 28
+
+/* Picophy reset defines */
+#define STIH407_PICOPHY0_RESET 0
+#define STIH407_PICOPHY1_RESET 1
+#define STIH407_PICOPHY2_RESET 2
+
+#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH407 */
--
1.9.1
More information about the linux-arm-kernel
mailing list