[PATCH v2 1/7] cpufreq: cpufreq-cpu0: allow optional safe voltage during frequency transitions
Lukasz Majewski
l.majewski at samsung.com
Tue Jan 28 10:06:33 EST 2014
Hi Thomas,
> Hi Lukasz,
>
> On Tue, Jan 28, 2014 at 1:47 PM, Lukasz Majewski
> <l.majewski at samsung.com> wrote:
> > Hi Thomas, Mike
> >
> >> Hi Mike,
> >>
> >> On Tue, Jan 28, 2014 at 1:55 AM, Mike Turquette
> >> <mturquette at linaro.org> wrote:
> >> > Quoting Thomas Abraham (2014-01-18 04:10:51)
> >> >> From: Thomas Abraham <thomas.ab at samsung.com>
> >> >>
> >> >> On some platforms such as the Samsung Exynos, changing the
> >> >> frequency of the CPU clock requires changing the frequency of
> >> >> the PLL that is supplying the CPU clock. To change the
> >> >> frequency of the PLL, the CPU clock is temporarily reparented
> >> >> to another parent clock.
> >> >>
> >> >> The clock frequency of this temporary parent clock could be much
> >> >> higher than the clock frequency of the PLL at the time of
> >> >> reparenting. Due to the temporary increase in the CPU clock
> >> >> speed, the CPU (and any other components in the CPU clock
> >> >> domain such as dividers, mux, etc.) have to to be operated at a
> >> >> higher voltage level, called the safe voltage level. This patch
> >> >> adds optional support to temporarily switch to a safe voltage
> >> >> level during CPU frequency transitions.
> >> >>
> >> >> Cc: Shawn Guo <shawn.guo at linaro.org>
> >> >> Signed-off-by: Thomas Abraham <thomas.ab at samsung.com>
> >> >
> >> > I'm not a fan of this change. This corner case should be
> >> > abstracted away somehow. I had talked to Chander Kayshap
> >> > previously about handling voltage changes in clock notifier
> >> > callbacks, which then renders any voltage change as a trivial
> >> > part of the clock rate transition. That means that this "safe
> >> > voltage" thing could be handled automagically without any
> >> > additional code in the CPUfreq driver.
> >> >
> >> > There are two nice ways to do this with the clock framework.
> >> > First is explicit re-parenting with voltage scaling done in the
> >> > clock rate-change notifiers:
> >> >
> >> > clk_set_parent(cpu_clk, temp_parent);
> >> > /* implicit voltage scaling to "safe voltage" happens above */
> >> > clk_set_rate(pll, some_rate);
> >> > clk_set_parent(cpu_clk, pll);
> >> > /* implicit voltage scaling to nominal OPP voltage happens above
> >> > */
> >> >
> >
> > I must agree with Mike here. In my opinion the above approach is
> > more compliant with CCF (as I've pointed it out in my other comment
> > - the cpu_clk has more than one parent and we could switch between
> > them when needed).
>
> The mux which is used to re-parent is part of the larger opaque cpu
> clock type (more like the composite clock). So I am not sure how this
> isn't compliant with ccf.
My point here is to use the clk_set_parent() explicitly instead of
changing the mux with writing values directly to registers.
However, I'm also aware, that we must reparent quickly. so I'm OK
with your approach.
>
> >
> >> > The above sequence would require a separate exnyos CPUfreq
> >> > driver, due to the added clk_set_parent logic.
> >> >
> >> > The second way to do this is to abstract the clk re-muxing logic
> >> > out into the clk driver, which would allow cpufreq-cpu0 to be
> >> > used for the exynos chips.
> >>
> >> This is the approach this patch series takes (patch 2/7). The clock
> >> re-muxing logic is handled by a clock driver code. The difference
> >> from what you suggested is that the safe voltage (that may be
> >> optionally) required before doing the re-muxing is handled here in
> >> cpufreq-cpu0 driver.
> >>
> >> The safe voltage setup can be done in the notifier as you
> >> suggested.
> >
> > If the clk_set_parent() approach is not suitable, then cannot we
> > consider using the one from highbank-cpufreq.c?
> >
> > Here we have cpufreq-cpu0.c which sets voltage of the cpu_clk.
> > In the highbank-cpufreq.c there are clock notifiers to change the
> > voltage.
> >
> > Cannot Exynos reuse such approach? Why shall we pollute
> > cpufreq-cpu0.c with another solution?
>
> The highbank-cpufreq.c file was introduced because platforms using
> this driver did not have the usual regulator to control the voltage.
> The first commit of this driver explains this (copied below).
>
> "Highbank processors depend on the external ECME to perform voltage
> management based on a requested frequency. Communication between the
> A9 cores and the ECME happens over the pl320 IPC channel."
>
> So those platforms had no choice but to use an alternative approach to
> control the voltage (and reuse cpufreq-cpu0 as much as possible).
> The
> case with exynos is a different one.
Highbank needs to set voltage via IPC, Exynos needs to adjust voltage
when reparenting.
Both can be recognized as unusual cases. That is why I asked if we
could reuse the same approach for Exynos.
> cpufreq-cpu0 is fully re-usable
> for exynos with the additional support for "safe voltage". If we agree
> that there might be existing or future platforms with single
> clock/voltage rail that require the "safe voltage" feature, then
> adding "safe voltage" support in cpufreq-cpu0 driver seems to be the
> right approach.
I think that Shawn's opinion will be final here.
>
> >
> >> But, doing that in cpufreq-cpu0 driver will help other platforms
> >> reuse this feature if required. Also, if done here, the regulator
> >> handling is localized in this driver which otherwise would need to
> >> be handled in two places, cpufreq-cpu0 driver and the clock
> >> notifier.
> >
> > I think that there is a logical distinction between setting voltage
> > for cpufreq-cpu0 related clock and increasing voltage of reparented
> > clock.
> >
> > The former fits naturally to cpufreq-cpu0, when the latter seems
> > like some corner case (as Mike pointed out) for Exynos.
>
> Agreed, it is a corner case. But for this corner case, we are
> performing some additional actions on the same regulator which is used
> in the normal functioning of the driver.
>
> >
> >>
> >> So I tend to prefer the approach in this patch but I am willing to
> >> consider any suggestions.
> >
> > Thomas, what do you think about highbank-cpufreq.c approach (with
> > using clock notifiers)?
>
> I have made a related comment on this above.
>
> >
> > Do you think, that it is feasible to reuse it with Exynos?
>
> highbank cpufreq driver is intended for a different purpose so I don't
> think it can be reused for exynos. Yes, we can make exynos specific
> hacks into highbank driver but how would that be better over the
> approach in this patch?
I think, that I was misunderstood here. I wanted to ask if we could
reuse the clk notifier approach.
>
> >
> >> Shawn, it would be helpful if you could let
> >> us know your thoughts on this. I am almost done with testing the
> >> v3 of this series and want to post it so if there are any
> >> objections to the changes in this patch, please let me know.
> >>
> >> Thanks,
> >> Thomas.
> >>
> >> >
> >> > I'm more a fan of explicitly listing the Exact Steps for the cpu
> >> > opp transition in a separate exynos-specific CPUfreq driver, but
> >> > that's probably an unpopular view.
> >> >
> >> > Regards,
> >> > Mike
> >> >
> >> >> ---
> >> >> .../devicetree/bindings/cpufreq/cpufreq-cpu0.txt | 7 ++++
> >> >> drivers/cpufreq/cpufreq-cpu0.c | 37
> >> >> +++++++++++++++++-- 2 files changed, 40 insertions(+), 4
> >> >> deletions(-)
> >> >>
> >> >> diff --git
> >> >> a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt
> >> >> b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt
> >> >> index f055515..37453ab 100644 ---
> >> >> a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt +++
> >> >> b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt @@
> >> >> -19,6 +19,12 @@ Optional properties:
> >> >> - cooling-min-level:
> >> >> - cooling-max-level:
> >> >> Please refer to
> >> >> Documentation/devicetree/bindings/thermal/thermal.txt. +-
> >> >> safe-opp: Certain platforms require that during a opp
> >> >> transition,
> >> >> + a system should not go below a particular opp level. For such
> >> >> systems,
> >> >> + this property specifies the minimum opp to be maintained
> >> >> during the
> >> >> + opp transitions. The safe-opp value is a tuple with first
> >> >> element
> >> >> + representing the safe frequency and the second element
> >> >> representing the
> >> >> + safe voltage.
> >> >>
> >> >> Examples:
> >> >>
> >> >> @@ -36,6 +42,7 @@ cpus {
> >> >> 396000 950000
> >> >> 198000 850000
> >> >> >;
> >> >> + safe-opp = <396000 950000>
> >> >> clock-latency = <61036>; /* two CLK32 periods */
> >> >> #cooling-cells = <2>;
> >> >> cooling-min-level = <0>;
> >> >> diff --git a/drivers/cpufreq/cpufreq-cpu0.c
> >> >> b/drivers/cpufreq/cpufreq-cpu0.c index 0c12ffc..075d3d1 100644
> >> >> --- a/drivers/cpufreq/cpufreq-cpu0.c
> >> >> +++ b/drivers/cpufreq/cpufreq-cpu0.c
> >> >> @@ -27,6 +27,8 @@
> >> >>
> >> >> static unsigned int transition_latency;
> >> >> static unsigned int voltage_tolerance; /* in percentage */
> >> >> +static unsigned long safe_frequency;
> >> >> +static unsigned long safe_voltage;
> >> >>
> >> >> static struct device *cpu_dev;
> >> >> static struct clk *cpu_clk;
> >> >> @@ -64,17 +66,30 @@ static int cpu0_set_target(struct
> >> >> cpufreq_policy *policy, unsigned int index) volt_old =
> >> >> regulator_get_voltage(cpu_reg); }
> >> >>
> >> >> - pr_debug("%u MHz, %ld mV --> %u MHz, %ld mV\n",
> >> >> + pr_debug("\n\n%u MHz, %ld mV --> %u MHz, %ld mV\n",
> >> >> old_freq / 1000, volt_old ? volt_old / 1000 :
> >> >> -1, new_freq / 1000, volt ? volt / 1000 : -1);
> >> >>
> >> >> /* scaling up? scale voltage before frequency */
> >> >> - if (!IS_ERR(cpu_reg) && new_freq > old_freq) {
> >> >> + if (!IS_ERR(cpu_reg) && new_freq > old_freq &&
> >> >> + new_freq >= safe_frequency) {
> >> >> ret = regulator_set_voltage_tol(cpu_reg, volt,
> >> >> tol); if (ret) {
> >> >> pr_err("failed to scale voltage up:
> >> >> %d\n", ret); return ret;
> >> >> }
> >> >> + } else if (!IS_ERR(cpu_reg) && old_freq <
> >> >> safe_frequency) {
> >> >> + /*
> >> >> + * the scaled up voltage level for the new_freq
> >> >> is lower
> >> >> + * than the safe voltage level. so set
> >> >> safe_voltage
> >> >> + * as the intermediate voltage level and revert
> >> >> it
> >> >> + * back after the frequency has been changed.
> >> >> + */
> >> >> + ret = regulator_set_voltage_tol(cpu_reg,
> >> >> safe_voltage, tol);
> >> >> + if (ret) {
> >> >> + pr_err("failed to set safe voltage:
> >> >> %d\n", ret);
> >> >> + return ret;
> >> >> + }
> >> >> }
> >> >>
> >> >> ret = clk_set_rate(cpu_clk, freq_exact);
> >> >> @@ -86,7 +101,8 @@ static int cpu0_set_target(struct
> >> >> cpufreq_policy *policy, unsigned int index) }
> >> >>
> >> >> /* scaling down? scale voltage after frequency */
> >> >> - if (!IS_ERR(cpu_reg) && new_freq < old_freq) {
> >> >> + if (!IS_ERR(cpu_reg) &&
> >> >> + (new_freq < old_freq || new_freq <
> >> >> safe_frequency)) { ret = regulator_set_voltage_tol(cpu_reg,
> >> >> volt, tol); if (ret) {
> >> >> pr_err("failed to scale voltage down:
> >> >> %d\n", ret); @@ -116,6 +132,8 @@ static struct cpufreq_driver
> >> >> cpu0_cpufreq_driver = {
> >> >>
> >> >> static int cpu0_cpufreq_probe(struct platform_device *pdev)
> >> >> {
> >> >> + const struct property *prop;
> >> >> + struct dev_pm_opp *opp;
> >> >> struct device_node *np;
> >> >> int ret;
> >> >>
> >> >> @@ -165,13 +183,24 @@ static int cpu0_cpufreq_probe(struct
> >> >> platform_device *pdev) goto out_put_node;
> >> >> }
> >> >>
> >> >> + prop = of_find_property(np, "safe-opp", NULL);
> >> >> + if (prop) {
> >> >> + if (prop->value && (prop->length / sizeof(u32))
> >> >> == 2) {
> >> >> + const __be32 *val;
> >> >> + val = prop->value;
> >> >> + safe_frequency = be32_to_cpup(val++);
> >> >> + safe_voltage = be32_to_cpup(val);
> >> >> + } else {
> >> >> + pr_err("invalid safe-opp level
> >> >> specified\n");
> >> >> + }
> >> >> + }
> >> >> +
> >> >> of_property_read_u32(np, "voltage-tolerance",
> >> >> &voltage_tolerance);
> >> >>
> >> >> if (of_property_read_u32(np, "clock-latency",
> >> >> &transition_latency)) transition_latency = CPUFREQ_ETERNAL;
> >> >>
> >> >> if (!IS_ERR(cpu_reg)) {
> >> >> - struct dev_pm_opp *opp;
> >> >> unsigned long min_uV, max_uV;
> >> >> int i;
> >> >>
> >> >> --
> >> >> 1.6.6.rc2
> >> >>
> >
> >
> >
> > --
> > Best regards,
> >
> > Lukasz Majewski
> >
> > Samsung R&D Institute Poland (SRPOL) | Linux Platform Group
>
> Thanks for your comments Lukasz.
>
> Regards,
> Thomas.
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Best regards,
Lukasz Majewski
Samsung R&D Institute Poland (SRPOL) | Linux Platform Group
More information about the linux-arm-kernel
mailing list