[PATCH v3 00/15] Device Tree support for the at91sam9261ek

[Jean-Jacques Hiblot]

This patch set aims at bringing a basic device tree support for the sam9261.
It's mostly based on the sam9263 and sam9x5 stuff.

Changes since V2:
* removed the smc driver from the serie. It'll be posted in an independent
  serie later.
* removed the DM9000 support (it'll come with the smc driver)
* the sam9261 now supports the Common Clock Framework (CCF). Note: to enable
  the CCF you must remove from the kernel config the platforms that don't
  support it.
* Added basic DT binding for the bus matrix
* Added support for USB host
* Added support for USB gadget
* in dts(i), replaced interrupt-parent with interrupts-extended
* changed the nand partition plan (same as for the sama5d3)
* removed 'mem' parameter in command line
* re-ordered dt-nodes in ascending address order.
* split the lcd support patch in 2 parts (SOC and board)


Change since V1:
* changed the DT representation to use address translation and separate the
  timings' configuration from the device properties by adding a "simple-bus"
  inetrmediate node.
* moved the smc driver from drivers/bus to drivers/memmory
* smc driver now accepts timings in nanoseconds as well as raw register values
* smc driver can clip the timings if they're out of bound and dump them to the
  console
* DM9000 timings are now described in nanosecs (for the virtue of example)

supported features:
* dbgu
* nand
* lcd
* leds
* user buttons
* usb host
* usb gadget

This serie relies on the 3 following patchs:
usb: ohci-at91: fix irq and iomem resource retrieval
usb: at91-udc: fix irq and iomem resource retrieval
ARM: at91: prepare sam9 dt boards transition to common

Jean-Jacques



Jean-Jacques Hiblot (15):
  at91: dt: Add at91sam9261 dt SoC support
  at91: dt: defconfig: Added the sam9261 to the list of supported SOCs
  at91: dt: sam9261: Basic Device Tree support for the at91sam9261ek
  ARM: at91: prepare common clk transition for sam9261 SoC
  ARM: at91: move sam9261 SoC to common clk
  at91: dt: at91sam9261ek: Adds DT entries for the 4 user buttons
  at91: dt: sam9261: Added the descriptions of hck0 and hck1 clocks
    (CCF)
  at91: dt: sam9261: Added hclk declaration for the fb driver (non-CCF)
  at91: dt: sam9261: Added support for the LCD display
  at91: dt: at91sam9261ek: Added support for the LCD display
  at91: dt: Adds support for the bus matrix declaration in the device
    tree
  at91: dt: sam9261: adds description for the bus matrix
  at91: dt: sam9261: CCF: Added USB clocks
  at91: dt: at91sam9261ek: Enabled the USB host port (OHCI)
  at91: dt: at91sam9261ek: Enabled the USB device port

 arch/arm/boot/dts/Makefile          |   2 +
 arch/arm/boot/dts/at91sam9261.dtsi  | 724 ++++++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/at91sam9261ek.dts | 191 ++++++++++
 arch/arm/configs/at91_dt_defconfig  |   1 +
 arch/arm/mach-at91/Kconfig          |   1 -
 arch/arm/mach-at91/at91sam9261.c    |  24 +-
 arch/arm/mach-at91/setup.c          |  23 ++
 7 files changed, 963 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi
 create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts

-- 
1.8.5.2