[PATCH v5 09/14] ARM: sunxi: Add support for Allwinner SUNXi SoCs sata to ahci_platform
Hans de Goede
hdegoede at redhat.com
Wed Jan 22 14:04:44 EST 2014
From: Olliver Schinagl <oliver at schinagl.nl>
This patch adds support for the ahci sata controler found on Allwinner A10
and A20 SoCs to the ahci_platform driver.
Orignally written by Olliver Schinagl using the approach of having a platform
device which probe method creates a new child platform device which gets
driven by ahci_platform.c, as done by ahci_imx.c .
Refactored by Hans de Goede to add most of the non sunxi specific functionality
to ahci_platform.c and use a platform_data pointer from of_device_id for the
sunxi specific bits.
Signed-off-by: Olliver Schinagl <oliver at schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
.../devicetree/bindings/ata/ahci-platform.txt | 18 +-
drivers/ata/Kconfig | 9 +
drivers/ata/Makefile | 1 +
drivers/ata/ahci_sunxi.c | 251 +++++++++++++++++++++
4 files changed, 276 insertions(+), 3 deletions(-)
create mode 100644 drivers/ata/ahci_sunxi.c
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
index 1ac807f..78b2e80 100644
--- a/Documentation/devicetree/bindings/ata/ahci-platform.txt
+++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -4,7 +4,9 @@ SATA nodes are defined to describe on-chip Serial ATA controllers.
Each SATA controller should have its own node.
Required properties:
-- compatible : compatible list, contains "snps,spear-ahci"
+- compatible : compatible list, one of "snps,spear-ahci",
+ "snps,exynos5440-ahci", "ibm,476gtr-ahci", or
+ "allwinner,sun4i-a10-ahci"
- interrupts : <interrupt mapping for SATA IRQ>
- reg : <registers mapping>
@@ -13,10 +15,20 @@ Optional properties:
- clocks : a list of phandle + clock specifier pairs
- target-supply : regulator for SATA target power
-Example:
+allwinner,sun4i-a10-ahci required properties:
+- clocks : index 0 must point to the sata_ref clk, 1 to the ahb clk
+
+Examples:
sata at ffe08000 {
compatible = "snps,spear-ahci";
reg = <0xffe08000 0x1000>;
interrupts = <115>;
-
};
+
+ ahci: sata at 01c18000 {
+ compatible = "allwinner,sun4i-a10-ahci";
+ reg = <0x01c18000 0x1000>;
+ interrupts = <56>;
+ clocks = <&pll6 0>, <&ahb_gates 25>;
+ target-supply = <®_ahci_5v>;
+ };
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 4e73772..cc67cc0 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -106,6 +106,15 @@ config AHCI_IMX
If unsure, say N.
+config AHCI_SUNXI
+ tristate "Allwinner sunxi AHCI SATA support"
+ depends on ARCH_SUNXI && SATA_AHCI_PLATFORM
+ help
+ This option enables support for the Allwinner sunxi SoC's
+ onboard AHCI SATA.
+
+ If unsure, say N.
+
config SATA_FSL
tristate "Freescale 3.0Gbps SATA support"
depends on FSL_SOC
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 46518c6..246050b 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
obj-$(CONFIG_AHCI_IMX) += ahci_imx.o
+obj-$(CONFIG_AHCI_SUNXI) += ahci_sunxi.o
# SFF w/ custom DMA
obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
diff --git a/drivers/ata/ahci_sunxi.c b/drivers/ata/ahci_sunxi.c
new file mode 100644
index 0000000..568a211
--- /dev/null
+++ b/drivers/ata/ahci_sunxi.c
@@ -0,0 +1,251 @@
+/*
+ * Allwinner sunxi AHCI SATA platform driver
+ * Copyright 2013 Olliver Schinagl <oliver at schinagl.nl>
+ * Copyright 2014 Hans de Goede <hdegoede at redhat.com>
+ *
+ * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
+ * Based on code from Allwinner Technology Co., Ltd. <www.allwinnertech.com>,
+ * Daniel Wang <danielwang at allwinnertech.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/ahci_platform.h>
+#include <linux/clk.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include "ahci.h"
+
+#define AHCI_BISTAFR 0x00a0
+#define AHCI_BISTCR 0x00a4
+#define AHCI_BISTFCTR 0x00a8
+#define AHCI_BISTSR 0x00ac
+#define AHCI_BISTDECR 0x00b0
+#define AHCI_DIAGNR0 0x00b4
+#define AHCI_DIAGNR1 0x00b8
+#define AHCI_OOBR 0x00bc
+#define AHCI_PHYCS0R 0x00c0
+#define AHCI_PHYCS1R 0x00c4
+#define AHCI_PHYCS2R 0x00c8
+#define AHCI_TIMER1MS 0x00e0
+#define AHCI_GPARAM1R 0x00e8
+#define AHCI_GPARAM2R 0x00ec
+#define AHCI_PPARAMR 0x00f0
+#define AHCI_TESTR 0x00f4
+#define AHCI_VERSIONR 0x00f8
+#define AHCI_IDR 0x00fc
+#define AHCI_RWCR 0x00fc
+#define AHCI_P0DMACR 0x0170
+#define AHCI_P0PHYCR 0x0178
+#define AHCI_P0PHYSR 0x017c
+
+static void sunxi_clrbits(void __iomem *reg, u32 clr_val)
+{
+ u32 reg_val;
+
+ reg_val = readl(reg);
+ reg_val &= ~(clr_val);
+ writel(reg_val, reg);
+}
+
+static void sunxi_setbits(void __iomem *reg, u32 set_val)
+{
+ u32 reg_val;
+
+ reg_val = readl(reg);
+ reg_val |= set_val;
+ writel(reg_val, reg);
+}
+
+static void sunxi_clrsetbits(void __iomem *reg, u32 clr_val, u32 set_val)
+{
+ u32 reg_val;
+
+ reg_val = readl(reg);
+ reg_val &= ~(clr_val);
+ reg_val |= set_val;
+ writel(reg_val, reg);
+}
+
+static u32 sunxi_getbits(void __iomem *reg, u8 mask, u8 shift)
+{
+ return (readl(reg) >> shift) & mask;
+}
+
+static int ahci_sunxi_phy_init(struct device *dev, void __iomem *reg_base)
+{
+ u32 reg_val;
+ int timeout;
+
+ /* This magic is from the original code */
+ writel(0, reg_base + AHCI_RWCR);
+ mdelay(5);
+
+ sunxi_setbits(reg_base + AHCI_PHYCS1R, BIT(19));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS0R,
+ (0x7 << 24),
+ (0x5 << 24) | BIT(23) | BIT(18));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS1R,
+ (0x3 << 16) | (0x1f << 8) | (0x3 << 6),
+ (0x2 << 16) | (0x6 << 8) | (0x2 << 6));
+ sunxi_setbits(reg_base + AHCI_PHYCS1R, BIT(28) | BIT(15));
+ sunxi_clrbits(reg_base + AHCI_PHYCS1R, BIT(19));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS0R,
+ (0x7 << 20), (0x3 << 20));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS2R,
+ (0x1f << 5), (0x19 << 5));
+ mdelay(5);
+
+ sunxi_setbits(reg_base + AHCI_PHYCS0R, (0x1 << 19));
+
+ timeout = 250; /* Power up takes aprox 50 us */
+ do {
+ reg_val = sunxi_getbits(reg_base + AHCI_PHYCS0R, 0x7, 28);
+ if (reg_val == 0x02)
+ break;
+
+ if (--timeout == 0) {
+ dev_err(dev, "PHY power up failed.\n");
+ return -EIO;
+ }
+ udelay(1);
+ } while (1);
+
+ sunxi_setbits(reg_base + AHCI_PHYCS2R, (0x1 << 24));
+
+ timeout = 100; /* Calibration takes aprox 10 us */
+ do {
+ reg_val = sunxi_getbits(reg_base + AHCI_PHYCS2R, 0x1, 24);
+ if (reg_val == 0x00)
+ break;
+
+ if (--timeout == 0) {
+ dev_err(dev, "PHY calibration failed.\n");
+ return -EIO;
+ }
+ udelay(1);
+ } while (1);
+
+ mdelay(15);
+
+ writel(0x7, reg_base + AHCI_RWCR);
+
+ return 0;
+}
+
+static void ahci_sunxi_start_engine(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+
+ /* Setup DMA before DMA start */
+ sunxi_clrsetbits(hpriv->mmio + AHCI_P0DMACR, 0x0000ff00, 0x00004400);
+
+ /* Start DMA */
+ sunxi_setbits(port_mmio + PORT_CMD, PORT_CMD_START);
+}
+
+static const struct ata_port_info ahci_sunxi_port_info = {
+ AHCI_HFLAGS(AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI |
+ AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ),
+ .flags = AHCI_FLAG_COMMON | ATA_FLAG_NCQ,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_platform_ops,
+};
+
+static int ahci_sunxi_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ahci_host_priv *hpriv;
+ int rc;
+
+ hpriv = ahci_platform_get_resources(pdev);
+ if (IS_ERR(hpriv))
+ return PTR_ERR(hpriv);
+
+ hpriv->start_engine = ahci_sunxi_start_engine;
+
+ rc = ahci_platform_enable_resources(hpriv);
+ if (rc)
+ goto put_resources;
+
+ rc = ahci_sunxi_phy_init(dev, hpriv->mmio);
+ if (rc)
+ goto disable_resources;
+
+ rc = ahci_platform_init_host(pdev, hpriv, &ahci_sunxi_port_info, 0, 0);
+ if (rc)
+ goto disable_resources;
+
+ return 0;
+
+disable_resources:
+ ahci_platform_disable_resources(hpriv);
+put_resources:
+ ahci_platform_put_resources(hpriv);
+ return rc;
+}
+
+#ifdef CONFIG_PM_SLEEP
+int ahci_sunxi_resume(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_host_priv *hpriv = host->private_data;
+ int rc;
+
+ rc = ahci_platform_enable_resources(hpriv);
+ if (rc)
+ return rc;
+
+ rc = ahci_sunxi_phy_init(dev, hpriv->mmio);
+ if (rc)
+ goto disable_resources;
+
+ rc = ahci_platform_resume_host(dev);
+ if (rc)
+ goto disable_resources;
+
+ return 0;
+
+disable_resources:
+ ahci_platform_disable_resources(hpriv);
+ return rc;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(ahci_sunxi_pm_ops, ahci_platform_suspend,
+ ahci_sunxi_resume);
+
+static const struct of_device_id ahci_sunxi_of_match[] = {
+ { .compatible = "allwinner,sun4i-a10-ahci", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, ahci_sunxi_of_match);
+
+static struct platform_driver ahci_sunxi_driver = {
+ .probe = ahci_sunxi_probe,
+ .remove = ata_platform_remove_one,
+ .driver = {
+ .name = "ahci-sunxi",
+ .owner = THIS_MODULE,
+ .of_match_table = ahci_sunxi_of_match,
+ .pm = &ahci_sunxi_pm_ops,
+ },
+};
+module_platform_driver(ahci_sunxi_driver);
+
+MODULE_DESCRIPTION("Allwinner sunxi AHCI SATA driver");
+MODULE_AUTHOR("Olliver Schinagl <oliver at schinagl.nl>");
+MODULE_LICENSE("GPL");
--
1.8.5.3
More information about the linux-arm-kernel
mailing list