[PATCHv3 27/41] ARM: omap3-beagle.dts: add display information

[Tomi Valkeinen]

Add DT data for OMAP3 Beagle board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo

Signed-off-by: Tomi Valkeinen <tomi.valkeinen at ti.com>
---
 arch/arm/boot/dts/omap3-beagle.dts | 116 +++++++++++++++++++++++++++++++++++++
 1 file changed, 116 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 3ba4a625ea5b..2b8efe355734 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -24,6 +24,11 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
+	aliases {
+		display0 = &dvi0;
+		display1 = &tv0;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pmu_stat {
@@ -80,6 +85,55 @@
 		};
 
 	};
+
+	tfp410: encoder at 0 {
+		compatible = "ti,tfp410";
+		gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;	/* 170, power-down */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tfp410_pins>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+
+				tfp410_in: endpoint at 0 {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port at 1 {
+				reg = <1>;
+
+				tfp410_out: endpoint at 0 {
+					remote-endpoint = <&dvi_connector_in>;
+				};
+			};
+		};
+	};
+
+	dvi0: connector at 0 {
+		compatible = "dvi-connector";
+		label = "dvi";
+
+		i2c-bus = <&i2c3>;
+
+		dvi_connector_in: endpoint {
+			remote-endpoint = <&tfp410_out>;
+		};
+	};
+
+	tv0: connector at 1 {
+		compatible = "svideo-connector";
+		label = "tv";
+
+		tv_connector_in: endpoint {
+			remote-endpoint = <&venc_out>;
+		};
+	};
 };
 
 &omap3_pmx_wkup {
@@ -119,6 +173,45 @@
 			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
+
+	tfp410_pins: pinmux_tfp410_pins {
+		pinctrl-single,pins = <
+			0x194 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
+		>;
+	};
+
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			0x0a4 (PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			0x0a6 (PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			0x0a8 (PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			0x0aa (PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+			0x0ac (PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
+			0x0ae (PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
+			0x0b0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
+			0x0b2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
+			0x0b4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
+			0x0b6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
+			0x0b8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			0x0ba (PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			0x0bc (PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			0x0be (PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			0x0c0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			0x0c2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			0x0c4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			0x0c6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			0x0c8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			0x0ca (PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			0x0cc (PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			0x0ce (PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+			0x0d0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data18.dss_data18 */
+			0x0d2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data19.dss_data19 */
+			0x0d4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data20.dss_data20 */
+			0x0d6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data21.dss_data21 */
+			0x0d8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
+			0x0da (PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
+		>;
+	};
 };
 
 &i2c1 {
@@ -199,3 +292,26 @@
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	dpi_out: endpoint {
+		remote-endpoint = <&tfp410_in>;
+		data-lines = <24>;
+	};
+};
+
+&venc {
+	status = "ok";
+
+	vdda-supply = <&vdac>;
+
+	venc_out: endpoint {
+		remote-endpoint = <&tv_connector_in>;
+		ti,channels = <2>;
+	};
+};
-- 
1.8.3.2