[PATCH 1/3] pinctrl: sh-pfc: r8a7791: Add QSPI pin groups

[Laurent Pinchart]

Hi Geert,

Thank you for the patch.

On Friday 03 January 2014 16:34:14 Geert Uytterhoeven wrote:
> From: Geert Uytterhoeven <geert+renesas at linux-m68k.org>
> 
> Signed-off-by: Geert Uytterhoeven <geert+renesas at linux-m68k.org>
> Cc: Linus Walleij <linus.walleij at linaro.org>
> ---
>  drivers/pinctrl/sh-pfc/pfc-r8a7791.c |   27 +++++++++++++++++++++++++++
>  1 file changed, 27 insertions(+)
> 
> diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
> b/drivers/pinctrl/sh-pfc/pfc-r8a7791.c index 654bef369ab8..0070243c859e
> 100644
> --- a/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
> +++ b/drivers/pinctrl/sh-pfc/pfc-r8a7791.c
> @@ -2135,6 +2135,25 @@ static const unsigned int msiof2_tx_pins[] = {
>  static const unsigned int msiof2_tx_mux[] = {
>  	MSIOF2_TXD_MARK,
>  };
> +/* - QSPI
> ------------------------------------------------------------------- */
> +static const unsigned int qspi_pins[] = {
> +	/* SPCLK, MOSI_IO0, MISO_IO1, IO2, IO3, SSL */
> +	RCAR_GP_PIN(1, 4), RCAR_GP_PIN(1, 5), RCAR_GP_PIN(1, 6),
> +	RCAR_GP_PIN(1, 7), RCAR_GP_PIN(1, 8), RCAR_GP_PIN(1, 9),
> +};

The QSPI controller can be used in 1-bit, 2-bit or 4-mode mode, so you should 
split the pins group to allow that. You could use one pin group for the 
control signals (SPCLK and SSL), one group for 2-bit data (MOSI + MISO, or IO0 
+ IO1 depending on the mode) and one group for 4-bit data (IO0 + IO1 + IO2 + 
IO3).

I assume that usage of the SSL signal is always required. If that's not the 
case the control signals group should be split in two.

Similarly, if the hardware supports "write-only" mode (where the MISO signal 
isn't connected), that should be supported through a 1-bit data signals group.

> +static const unsigned int qspi_mux[] = {
> +	SPCLK_MARK, MOSI_IO0_MARK, MISO_IO1_MARK,
> +	IO2_MARK, IO3_MARK, SSL_MARK
> +};
> +static const unsigned int qspi_b_pins[] = {
> +	/* SPCLK, MOSI_IO0, MISO_IO1, IO2, IO3, SSL */
> +	RCAR_GP_PIN(6, 0), RCAR_GP_PIN(6, 1), RCAR_GP_PIN(6, 2),
> +	RCAR_GP_PIN(6, 3), RCAR_GP_PIN(6, 4), RCAR_GP_PIN(6, 5),
> +};
> +static const unsigned int qspi_b_mux[] = {
> +	SPCLK_B_MARK, MOSI_IO0_B_MARK, MISO_IO1_B_MARK,
> +	IO2_B_MARK, IO3_B_MARK, SSL_B_MARK
> +};
>  /* - SCIF0
> ------------------------------------------------------------------ */
> static const unsigned int scif0_data_pins[] = {
>  	/* RX, TX */
> @@ -2877,6 +2896,8 @@ static const struct sh_pfc_pin_group pinmux_groups[] =
> { SH_PFC_PIN_GROUP(msiof2_ss2),
>  	SH_PFC_PIN_GROUP(msiof2_rx),
>  	SH_PFC_PIN_GROUP(msiof2_tx),
> +	SH_PFC_PIN_GROUP(qspi),
> +	SH_PFC_PIN_GROUP(qspi_b),
>  	SH_PFC_PIN_GROUP(scif0_data),
>  	SH_PFC_PIN_GROUP(scif0_data_b),
>  	SH_PFC_PIN_GROUP(scif0_data_c),
> @@ -3074,6 +3095,11 @@ static const char * const msiof2_groups[] = {
>  	"msiof2_tx",
>  };
> 
> +static const char * const qspi_groups[] = {
> +	"qspi",
> +	"qspi_b",
> +};
> +
>  static const char * const scif0_groups[] = {
>  	"scif0_data",
>  	"scif0_data_b",
> @@ -3230,6 +3256,7 @@ static const struct sh_pfc_function pinmux_functions[]
> = { SH_PFC_FUNCTION(msiof0),
>  	SH_PFC_FUNCTION(msiof1),
>  	SH_PFC_FUNCTION(msiof2),
> +	SH_PFC_FUNCTION(qspi),
>  	SH_PFC_FUNCTION(scif0),
>  	SH_PFC_FUNCTION(scif1),
>  	SH_PFC_FUNCTION(scif2),
-- 
Regards,

Laurent Pinchart