[PATCH] ARM: dts: vf610: use the interrupt macros
Shawn Guo
shawn.guo at linaro.org
Mon Jan 6 01:04:33 EST 2014
On Wed, Dec 25, 2013 at 02:19:27PM +0800, Huang Shijie wrote:
> This patch uses the IRQ_TYPE_LEVEL_HIGH/IRQ_TYPE_NONE to replace
> the hardcode.
>
> Signed-off-by: Huang Shijie <b32955 at freescale.com>
> ---
> arch/arm/boot/dts/vf610.dtsi | 37 +++++++++++++++++++------------------
> 1 files changed, 19 insertions(+), 18 deletions(-)
>
> diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi
> index ef8a0ee..cd5bb86 100644
> --- a/arch/arm/boot/dts/vf610.dtsi
> +++ b/arch/arm/boot/dts/vf610.dtsi
> @@ -10,6 +10,7 @@
> #include "skeleton.dtsi"
> #include "vf610-pingrp.h"
> #include <dt-bindings/clock/vf610-clock.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>
> / {
> aliases {
> @@ -90,7 +91,7 @@
> uart0: serial at 40027000 {
> compatible = "fsl,vf610-lpuart";
> reg = <0x40027000 0x1000>;
> - interrupts = <0 61 0x00>;
Why is it so special having a 0x00 IRQ trigger type? Or is it just a
typo? While we are at it, we should probably fix it if it's a typo.
Shawn
> + interrupts = <0 61 IRQ_TYPE_NONE>;
> clocks = <&clks VF610_CLK_UART0>;
> clock-names = "ipg";
> status = "disabled";
> @@ -99,7 +100,7 @@
> uart1: serial at 40028000 {
> compatible = "fsl,vf610-lpuart";
> reg = <0x40028000 0x1000>;
> - interrupts = <0 62 0x04>;
> + interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_UART1>;
> clock-names = "ipg";
> status = "disabled";
> @@ -108,7 +109,7 @@
> uart2: serial at 40029000 {
> compatible = "fsl,vf610-lpuart";
> reg = <0x40029000 0x1000>;
> - interrupts = <0 63 0x04>;
> + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_UART2>;
> clock-names = "ipg";
> status = "disabled";
> @@ -117,7 +118,7 @@
> uart3: serial at 4002a000 {
> compatible = "fsl,vf610-lpuart";
> reg = <0x4002a000 0x1000>;
> - interrupts = <0 64 0x04>;
> + interrupts = <0 64 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_UART3>;
> clock-names = "ipg";
> status = "disabled";
> @@ -128,7 +129,7 @@
> #size-cells = <0>;
> compatible = "fsl,vf610-dspi";
> reg = <0x4002c000 0x1000>;
> - interrupts = <0 67 0x04>;
> + interrupts = <0 67 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_DSPI0>;
> clock-names = "dspi";
> spi-num-chipselects = <5>;
> @@ -138,7 +139,7 @@
> sai2: sai at 40031000 {
> compatible = "fsl,vf610-sai";
> reg = <0x40031000 0x1000>;
> - interrupts = <0 86 0x04>;
> + interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_SAI2>;
> clock-names = "sai";
> status = "disabled";
> @@ -147,7 +148,7 @@
> pit: pit at 40037000 {
> compatible = "fsl,vf610-pit";
> reg = <0x40037000 0x1000>;
> - interrupts = <0 39 0x04>;
> + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_PIT>;
> clock-names = "pit";
> };
> @@ -164,7 +165,7 @@
> #size-cells = <0>;
> compatible = "fsl,vf610-qspi";
> reg = <0x40044000 0x1000>;
> - interrupts = <0 24 0x04>;
> + interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_QSPI0_EN>,
> <&clks VF610_CLK_QSPI0>;
> clock-names = "qspi_en", "qspi";
> @@ -180,7 +181,7 @@
> gpio1: gpio at 40049000 {
> compatible = "fsl,vf610-gpio";
> reg = <0x40049000 0x1000 0x400ff000 0x40>;
> - interrupts = <0 107 0x04>;
> + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>;
> gpio-controller;
> #gpio-cells = <2>;
> interrupt-controller;
> @@ -191,7 +192,7 @@
> gpio2: gpio at 4004a000 {
> compatible = "fsl,vf610-gpio";
> reg = <0x4004a000 0x1000 0x400ff040 0x40>;
> - interrupts = <0 108 0x04>;
> + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
> gpio-controller;
> #gpio-cells = <2>;
> interrupt-controller;
> @@ -202,7 +203,7 @@
> gpio3: gpio at 4004b000 {
> compatible = "fsl,vf610-gpio";
> reg = <0x4004b000 0x1000 0x400ff080 0x40>;
> - interrupts = <0 109 0x04>;
> + interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>;
> gpio-controller;
> #gpio-cells = <2>;
> interrupt-controller;
> @@ -213,7 +214,7 @@
> gpio4: gpio at 4004c000 {
> compatible = "fsl,vf610-gpio";
> reg = <0x4004c000 0x1000 0x400ff0c0 0x40>;
> - interrupts = <0 110 0x04>;
> + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
> gpio-controller;
> #gpio-cells = <2>;
> interrupt-controller;
> @@ -224,7 +225,7 @@
> gpio5: gpio at 4004d000 {
> compatible = "fsl,vf610-gpio";
> reg = <0x4004d000 0x1000 0x400ff100 0x40>;
> - interrupts = <0 111 0x04>;
> + interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>;
> gpio-controller;
> #gpio-cells = <2>;
> interrupt-controller;
> @@ -242,7 +243,7 @@
> #size-cells = <0>;
> compatible = "fsl,vf610-i2c";
> reg = <0x40066000 0x1000>;
> - interrupts =<0 71 0x04>;
> + interrupts =<0 71 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_I2C0>;
> clock-names = "ipg";
> status = "disabled";
> @@ -265,7 +266,7 @@
> uart4: serial at 400a9000 {
> compatible = "fsl,vf610-lpuart";
> reg = <0x400a9000 0x1000>;
> - interrupts = <0 65 0x04>;
> + interrupts = <0 65 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_UART4>;
> clock-names = "ipg";
> status = "disabled";
> @@ -274,7 +275,7 @@
> uart5: serial at 400aa000 {
> compatible = "fsl,vf610-lpuart";
> reg = <0x400aa000 0x1000>;
> - interrupts = <0 66 0x04>;
> + interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_UART5>;
> clock-names = "ipg";
> status = "disabled";
> @@ -283,7 +284,7 @@
> fec0: ethernet at 400d0000 {
> compatible = "fsl,mvf600-fec";
> reg = <0x400d0000 0x1000>;
> - interrupts = <0 78 0x04>;
> + interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_ENET0>,
> <&clks VF610_CLK_ENET0>,
> <&clks VF610_CLK_ENET>;
> @@ -294,7 +295,7 @@
> fec1: ethernet at 400d1000 {
> compatible = "fsl,mvf600-fec";
> reg = <0x400d1000 0x1000>;
> - interrupts = <0 79 0x04>;
> + interrupts = <0 79 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clks VF610_CLK_ENET1>,
> <&clks VF610_CLK_ENET1>,
> <&clks VF610_CLK_ENET>;
> --
> 1.7.2.rc3
>
>
More information about the linux-arm-kernel
mailing list