[PATCH v2 1/2] spi: spi-imx: enable dma support for escpi controller
Frank Li
Frank.Li at freescale.com
Fri Jan 3 17:53:51 EST 2014
After enable DMA
spi-nor read speed is
dd if=/dev/mtd0 of=/dev/null bs=1M count=1
1+0 records in
1+0 records out
1048576 bytes (1.0 MB) copied, 0.720402 s, 1.5 MB/s
spi-nor write speed is
dd if=/dev/zero of=/dev/mtd0 bs=1M count=1
1+0 records in
1+0 records out
1048576 bytes (1.0 MB) copied, 3.56044 s, 295 kB/s
Before enable DMA
spi-nor read speed is
dd if=/dev/mtd0 of=/dev/null bs=1M count=1
1+0 records in
1+0 records out
1048576 bytes (1.0 MB) copied, 2.37717 s, 441 kB/s
spi-nor write speed is
dd if=/dev/zero of=/dev/mtd0 bs=1M count=1
1+0 records in
1+0 records out
1048576 bytes (1.0 MB) copied, 4.83181 s, 217 kB/s
Signed-off-by: Frank Li <Frank.Li at freescale.com>
---
drivers/spi/spi-imx.c | 447 ++++++++++++++++++++++++++++++++++++++++++++++++-
1 files changed, 441 insertions(+), 6 deletions(-)
Change from v1.
1. check if res is null at res = platform_get_resource(pdev, IORESOURCE_MEM, 0)
2. fix failure transfer when len is not multiple watermark
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index b80f2f7..1a9099a 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -39,6 +39,10 @@
#include <linux/of_gpio.h>
#include <linux/platform_data/spi-imx.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_data/dma-imx.h>
+#include <linux/dmaengine.h>
+
#define DRIVER_NAME "spi_imx"
@@ -52,6 +56,9 @@
#define MXC_INT_RR (1 << 0) /* Receive data ready interrupt */
#define MXC_INT_TE (1 << 1) /* Transmit FIFO empty interrupt */
+/* The maximum bytes that a sdma BD can transfer.*/
+#define MAX_SDMA_BD_BYTES (1 << 15)
+
struct spi_imx_config {
unsigned int speed_hz;
unsigned int bpw;
@@ -84,6 +91,7 @@ struct spi_imx_data {
struct completion xfer_done;
void __iomem *base;
+ resource_size_t mapbase;
int irq;
struct clk *clk_per;
struct clk *clk_ipg;
@@ -92,6 +100,29 @@ struct spi_imx_data {
unsigned int count;
void (*tx)(struct spi_imx_data *);
void (*rx)(struct spi_imx_data *);
+ int (*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t);
+ struct dma_chan *dma_chan_rx, *dma_chan_tx;
+ unsigned int dma_is_inited;
+ struct device *dev;
+
+ struct completion dma_rx_completion;
+ struct completion dma_tx_completion;
+
+ u8 *dma_rx_tmpbuf;
+ unsigned int dma_rx_tmpbuf_size;
+ unsigned int dma_rx_tmpbuf_phy_addr;
+
+ u8 *dma_tx_tmpbuf;
+ unsigned int dma_tx_tmpbuf_size;
+ unsigned int dma_tx_tmpbuf_phy_addr;
+
+ unsigned int usedma;
+ unsigned int dma_finished;
+ /* SDMA wartermark */
+ u32 rx_wml;
+ u32 tx_wml;
+ u32 rxt_wml;
+
void *rx_buf;
const void *tx_buf;
unsigned int txfifo; /* number of words pushed in tx FIFO */
@@ -185,6 +216,7 @@ static unsigned int spi_imx_clkdiv_2(unsigned int fin,
#define MX51_ECSPI_CTRL 0x08
#define MX51_ECSPI_CTRL_ENABLE (1 << 0)
#define MX51_ECSPI_CTRL_XCH (1 << 2)
+#define MX51_ECSPI_CTRL_SMC (1 << 3)
#define MX51_ECSPI_CTRL_MODE_MASK (0xf << 4)
#define MX51_ECSPI_CTRL_POSTDIV_OFFSET 8
#define MX51_ECSPI_CTRL_PREDIV_OFFSET 12
@@ -202,9 +234,22 @@ static unsigned int spi_imx_clkdiv_2(unsigned int fin,
#define MX51_ECSPI_INT_TEEN (1 << 0)
#define MX51_ECSPI_INT_RREN (1 << 3)
+#define MX51_ECSPI_DMA 0x14
+#define MX51_ECSPI_DMA_TX_WML_OFFSET 0
+#define MX51_ECSPI_DMA_TX_WML_MASK 0x3F
+#define MX51_ECSPI_DMA_RX_WML_OFFSET 16
+#define MX51_ECSPI_DMA_RX_WML_MASK (0x3F << 16)
+#define MX51_ECSPI_DMA_RXT_WML_OFFSET 24
+#define MX51_ECSPI_DMA_RXT_WML_MASK (0x3F << 16)
+
+#define MX51_ECSPI_DMA_TEDEN_OFFSET 7
+#define MX51_ECSPI_DMA_RXDEN_OFFSET 23
+#define MX51_ECSPI_DMA_RXTDEN_OFFSET 31
+
#define MX51_ECSPI_STAT 0x18
#define MX51_ECSPI_STAT_RR (1 << 3)
+#define MX51_ECSPI_TESTREG 0x20
/* MX51 eCSPI */
static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi)
{
@@ -255,16 +300,28 @@ static void __maybe_unused mx51_ecspi_trigger(struct spi_imx_data *spi_imx)
{
u32 reg;
- reg = readl(spi_imx->base + MX51_ECSPI_CTRL);
- reg |= MX51_ECSPI_CTRL_XCH;
- writel(reg, spi_imx->base + MX51_ECSPI_CTRL);
+ if (!spi_imx->usedma) {
+ reg = readl(spi_imx->base + MX51_ECSPI_CTRL);
+ reg |= MX51_ECSPI_CTRL_XCH;
+ writel(reg, spi_imx->base + MX51_ECSPI_CTRL);
+ } else {
+ if (!spi_imx->dma_finished) {
+ reg = readl(spi_imx->base + MX51_ECSPI_CTRL);
+ reg |= MX51_ECSPI_CTRL_SMC;
+ writel(reg, spi_imx->base + MX51_ECSPI_CTRL);
+ } else {
+ reg = readl(spi_imx->base + MX51_ECSPI_CTRL);
+ reg &= (~MX51_ECSPI_CTRL_SMC);
+ writel(reg, spi_imx->base + MX51_ECSPI_CTRL);
+ }
+ }
}
static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx,
struct spi_imx_config *config)
{
- u32 ctrl = MX51_ECSPI_CTRL_ENABLE, cfg = 0;
-
+ u32 ctrl = MX51_ECSPI_CTRL_ENABLE, cfg = 0, dma = 0;
+ u32 tx_wml_cfg, rx_wml_cfg, rxt_wml_cfg;
/*
* The hardware seems to have a race condition when changing modes. The
* current assumption is that the selection of the channel arrives
@@ -297,6 +354,30 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx,
writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
+ /*
+ * Configure the DMA register: setup the watermark
+ * and enable DMA request.
+ */
+ if (spi_imx->dma_is_inited) {
+ dma = readl(spi_imx->base + MX51_ECSPI_DMA);
+
+ spi_imx->tx_wml = spi_imx_get_fifosize(spi_imx) / 2;
+ spi_imx->rx_wml = spi_imx_get_fifosize(spi_imx) / 2;
+ spi_imx->rxt_wml = spi_imx_get_fifosize(spi_imx) / 2;
+ rx_wml_cfg = spi_imx->rx_wml << MX51_ECSPI_DMA_RX_WML_OFFSET;
+ tx_wml_cfg = spi_imx->tx_wml << MX51_ECSPI_DMA_TX_WML_OFFSET;
+ rxt_wml_cfg = spi_imx->rxt_wml << MX51_ECSPI_DMA_RXT_WML_OFFSET;
+ dma = (dma & (~MX51_ECSPI_DMA_TX_WML_MASK)
+ & (~MX51_ECSPI_DMA_RX_WML_MASK)
+ & (~MX51_ECSPI_DMA_RXT_WML_MASK))
+ | rx_wml_cfg | tx_wml_cfg | rxt_wml_cfg
+ | (1 << MX51_ECSPI_DMA_TEDEN_OFFSET)
+ | (1 << MX51_ECSPI_DMA_RXDEN_OFFSET)
+ | (1 << MX51_ECSPI_DMA_RXTDEN_OFFSET);
+
+ writel(dma, spi_imx->base + MX51_ECSPI_DMA);
+ }
+
return 0;
}
@@ -708,7 +789,285 @@ static int spi_imx_setupxfer(struct spi_device *spi,
return 0;
}
-static int spi_imx_transfer(struct spi_device *spi,
+static void spi_imx_sdma_exit(struct spi_imx_data *spi_imx)
+{
+ if (spi_imx->dma_chan_rx) {
+ dma_release_channel(spi_imx->dma_chan_rx);
+ spi_imx->dma_chan_rx = NULL;
+ }
+
+ if (spi_imx->dma_chan_tx) {
+ dma_release_channel(spi_imx->dma_chan_tx);
+ spi_imx->dma_chan_tx = NULL;
+ }
+
+ spi_imx->dma_is_inited = 0;
+}
+
+static void spi_imx_dma_rx_callback(void *cookie)
+{
+ struct spi_imx_data *spi_imx = (struct spi_imx_data *)cookie;
+
+ complete(&spi_imx->dma_rx_completion);
+
+}
+
+static void spi_imx_dma_tx_callback(void *cookie)
+{
+ struct spi_imx_data *spi_imx = (struct spi_imx_data *)cookie;
+
+ complete(&spi_imx->dma_tx_completion);
+}
+
+static int spi_imx_sdma_transfer(struct spi_device *spi,
+ struct spi_transfer *transfer)
+{
+ struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+ int ret = 0;
+ int sg_num;
+ int loop;
+ int left;
+ u32 dma;
+
+ struct scatterlist *sg_rx, *sg_tx;
+ struct dma_async_tx_descriptor *txdesc;
+ struct dma_async_tx_descriptor *rxdesc;
+
+ init_completion(&spi_imx->dma_rx_completion);
+ init_completion(&spi_imx->dma_tx_completion);
+
+ /*
+ * Get the valid physical address for the tx buf, if the rx buf address
+ * is null or it cannot be mapped, we should allocate memory for it.
+ */
+ if (virt_addr_valid(transfer->tx_buf)) {
+ transfer->tx_dma = dma_map_single(spi_imx->dev,
+ (void *)transfer->tx_buf, transfer->len,
+ DMA_TO_DEVICE);
+ if (dma_mapping_error(spi_imx->dev, transfer->tx_dma)) {
+ dev_err(spi_imx->dev,
+ "Memory dma map fail, line = %d\n", __LINE__);
+ ret = -EFAULT;
+ goto err_tx;
+ }
+ } else {
+ if (transfer->len > spi_imx->dma_tx_tmpbuf_size) {
+ if (!spi_imx->dma_tx_tmpbuf_size) {
+ kfree(spi_imx->dma_tx_tmpbuf);
+ spi_imx->dma_tx_tmpbuf_size = 0;
+ }
+
+ spi_imx->dma_tx_tmpbuf =
+ kzalloc(transfer->len, GFP_KERNEL);
+ if (NULL == spi_imx->dma_tx_tmpbuf) {
+ dev_err(spi_imx->dev, "Alloc memory fail.\n");
+ ret = -EFAULT;
+ goto err_tx;
+ }
+ spi_imx->dma_tx_tmpbuf_size = transfer->len;
+ }
+
+ /*
+ * Move the transfered data to new buffer from the old one
+ * that cannot be mapped.
+ */
+ if (transfer->tx_buf)
+ memcpy(spi_imx->dma_tx_tmpbuf,
+ transfer->tx_buf,
+ transfer->len);
+
+ spi_imx->dma_tx_tmpbuf_phy_addr = dma_map_single(spi_imx->dev,
+ spi_imx->dma_tx_tmpbuf, transfer->len,
+ DMA_TO_DEVICE);
+
+ if (dma_mapping_error(spi_imx->dev,
+ spi_imx->dma_tx_tmpbuf_phy_addr)) {
+ dev_err(spi_imx->dev,
+ "Memory dma map fail, line = %d\n",
+ __LINE__);
+ ret = -EFAULT;
+ goto err_tx;
+ }
+
+ transfer->tx_dma = spi_imx->dma_tx_tmpbuf_phy_addr;
+ }
+
+ /* Prepare sg for tx sdma. */
+ sg_num = ((transfer->len - 1) / MAX_SDMA_BD_BYTES) + 1;
+ sg_tx = kzalloc(sg_num * sizeof(struct scatterlist), GFP_KERNEL);
+ if (NULL == sg_tx) {
+ dev_err(spi_imx->dev,
+ "Memory allocate fail, line = %d\n",
+ __LINE__);
+ goto err_tx_sg;
+ }
+ sg_init_table(sg_tx, sg_num);
+ for (loop = 0; loop < (sg_num - 1); loop++) {
+ sg_dma_address(&sg_tx[loop]) =
+ transfer->tx_dma + loop * MAX_SDMA_BD_BYTES;
+ sg_dma_len(&sg_tx[loop]) = MAX_SDMA_BD_BYTES;
+ }
+
+ sg_dma_address(&sg_tx[loop]) =
+ transfer->tx_dma + loop * MAX_SDMA_BD_BYTES;
+ sg_dma_len(&sg_tx[loop]) = transfer->len - loop * MAX_SDMA_BD_BYTES;
+
+ txdesc = dmaengine_prep_slave_sg(spi_imx->dma_chan_tx,
+ sg_tx, sg_num , DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT);
+ if (!txdesc) {
+ ret = -EFAULT;
+ goto err_rx;
+ }
+
+ txdesc->callback = spi_imx_dma_tx_callback;
+ txdesc->callback_param = (void *)spi_imx;
+
+ /*
+ * Get the valid physical address for the rx buf, if the rx buf address
+ * is null or it cannot be mapped, we should allocate memory for it.
+ */
+ if (virt_addr_valid(transfer->rx_buf)) {
+ transfer->rx_dma = dma_map_single(spi_imx->dev,
+ transfer->rx_buf, transfer->len,
+ DMA_FROM_DEVICE);
+
+ if (dma_mapping_error(spi_imx->dev, transfer->rx_dma)) {
+ dev_err(spi_imx->dev,
+ "Memory allocate fail, line = %d\n",
+ __LINE__);
+ ret = -EFAULT;
+ goto err_rx;
+ }
+ } else {
+ if (transfer->len > spi_imx->dma_rx_tmpbuf_size) {
+ if (!spi_imx->dma_rx_tmpbuf_size) {
+ kfree(spi_imx->dma_rx_tmpbuf);
+ spi_imx->dma_rx_tmpbuf_size = 0;
+ }
+
+ spi_imx->dma_rx_tmpbuf =
+ kzalloc(transfer->len, GFP_KERNEL);
+ if (NULL == spi_imx->dma_rx_tmpbuf) {
+ dev_err(spi_imx->dev, "Alloc memory fail.\n");
+ ret = -EFAULT;
+ goto err_rx;
+ }
+ spi_imx->dma_rx_tmpbuf_size = transfer->len;
+ }
+
+ spi_imx->dma_rx_tmpbuf_phy_addr = dma_map_single(spi_imx->dev,
+ spi_imx->dma_rx_tmpbuf, transfer->len,
+ DMA_FROM_DEVICE);
+
+ if (dma_mapping_error(spi_imx->dev,
+ spi_imx->dma_rx_tmpbuf_phy_addr)) {
+ dev_err(spi_imx->dev,
+ "Memory dma map fail, line = %d\n",
+ __LINE__);
+ ret = -EFAULT;
+ goto err_rx;
+ }
+
+ transfer->rx_dma = spi_imx->dma_rx_tmpbuf_phy_addr;
+ }
+
+ /* Prepare sg for rx sdma. */
+ sg_num = ((transfer->len - 1) / MAX_SDMA_BD_BYTES) + 1;
+ sg_rx = kzalloc(sg_num * sizeof(struct scatterlist), GFP_KERNEL);
+ if (NULL == sg_rx) {
+ dev_err(spi_imx->dev,
+ "Memory dma map fail, line = %d\n", __LINE__);
+ goto err_rx_sg;
+ }
+ sg_init_table(sg_rx, sg_num);
+ for (loop = 0; loop < (sg_num - 1); loop++) {
+ sg_dma_address(&sg_rx[loop]) =
+ transfer->rx_dma + loop * MAX_SDMA_BD_BYTES;
+ sg_dma_len(&sg_rx[loop]) = MAX_SDMA_BD_BYTES;
+ }
+
+ sg_dma_address(&sg_rx[loop]) =
+ transfer->rx_dma + loop * MAX_SDMA_BD_BYTES;
+ sg_dma_len(&sg_rx[loop]) = transfer->len - loop * MAX_SDMA_BD_BYTES;
+ rxdesc = dmaengine_prep_slave_sg(spi_imx->dma_chan_rx,
+ sg_rx, sg_num , DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);
+ if (!rxdesc) {
+ ret = -EFAULT;
+ goto err_desc;
+ }
+
+ rxdesc->callback = spi_imx_dma_rx_callback;
+ rxdesc->callback_param = (void *)spi_imx;
+
+ /* Trigger the cspi module. */
+ spi_imx->dma_finished = 0;
+
+ spi_imx->devtype_data->trigger(spi_imx);
+
+ dmaengine_submit(txdesc);
+ dmaengine_submit(rxdesc);
+
+ dma_async_issue_pending(spi_imx->dma_chan_tx);
+ dma_async_issue_pending(spi_imx->dma_chan_rx);
+
+ /* Wait SDMA to finish the data transfer.*/
+ ret = wait_for_completion_timeout(&spi_imx->dma_tx_completion,
+ msecs_to_jiffies(3000));
+ if (!ret) {
+ dev_err(spi_imx->dev,
+ "I/O Error in DMA TX, line = %d ####\n", __LINE__);
+ dmaengine_terminate_all(spi_imx->dma_chan_tx);
+ goto err_desc;
+ } else {
+ dma = readl(spi_imx->base + MX51_ECSPI_DMA);
+ dma = dma & (~MX51_ECSPI_DMA_RXT_WML_MASK);
+ /* Change RX_DMA_LENGTH trigger dma fetch tail data */
+ left = transfer->len & (~spi_imx->rxt_wml);
+ if (left)
+ writel(dma | (left << MX51_ECSPI_DMA_RXT_WML_OFFSET),
+ spi_imx->base + MX51_ECSPI_DMA);
+
+ ret = wait_for_completion_timeout(&spi_imx->dma_rx_completion,
+ msecs_to_jiffies(3000));
+
+ writel(dma | (spi_imx->rxt_wml << MX51_ECSPI_DMA_RXT_WML_OFFSET),
+ spi_imx->base + MX51_ECSPI_DMA);
+ if (!ret) {
+ dev_err(spi_imx->dev,
+ "I/O Error in DMA RX. len %d, line = %d\n",
+ transfer->len,
+ __LINE__);
+ spi_imx->devtype_data->reset(spi_imx);
+ dmaengine_terminate_all(spi_imx->dma_chan_rx);
+ }
+ }
+
+ /* Move the transfered data to rx buf when it cannot be mapped.*/
+ if (transfer->rx_buf && (!virt_addr_valid(transfer->rx_buf)))
+ memcpy(transfer->rx_buf,
+ spi_imx->dma_rx_tmpbuf,
+ transfer->len);
+
+err_desc:
+ kfree(sg_rx);
+err_rx_sg:
+ dma_unmap_single(spi_imx->dev, transfer->rx_dma,
+ transfer->len, DMA_TO_DEVICE);
+err_rx:
+ kfree(sg_tx);
+err_tx_sg:
+ dma_unmap_single(spi_imx->dev, transfer->tx_dma,
+ transfer->len, DMA_FROM_DEVICE);
+err_tx:
+ spi_imx->dma_finished = 1;
+ spi_imx->devtype_data->trigger(spi_imx);
+ if ((!ret) || (-EFAULT == ret))
+ return -EIO;
+ else
+ return transfer->len;
+}
+
+static int spi_imx_pio_transfer(struct spi_device *spi,
struct spi_transfer *transfer)
{
struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
@@ -729,6 +1088,27 @@ static int spi_imx_transfer(struct spi_device *spi,
return transfer->len;
}
+static int spi_imx_transfer(struct spi_device *spi,
+ struct spi_transfer *transfer)
+{
+ struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+
+ if (spi_imx->dma_chan_tx && spi_imx->dma_chan_rx) {
+ /*
+ * Don't use sdma when the size of data to be transfered is
+ * lower then SDMA wartermark.
+ */
+ if ((transfer->len >= spi_imx->rx_wml) &&
+ (transfer->len > spi_imx->tx_wml)) {
+ spi_imx->usedma = 1;
+ return spi_imx_sdma_transfer(spi, transfer);
+ }
+ }
+
+ spi_imx->usedma = 0;
+ return spi_imx_pio_transfer(spi, transfer);
+}
+
static int spi_imx_setup(struct spi_device *spi)
{
struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
@@ -778,6 +1158,56 @@ spi_imx_unprepare_message(struct spi_master *master, struct spi_message *msg)
return 0;
}
+static int spi_imx_sdma_init(struct spi_imx_data *spi_imx)
+{
+ struct dma_slave_config slave_config = {};
+ struct device *dev = spi_imx->dev;
+ int ret;
+
+
+ /* Prepare for TX : */
+ spi_imx->dma_chan_tx = dma_request_slave_channel(dev, "tx");
+ if (!spi_imx->dma_chan_tx) {
+ dev_err(dev, "cannot get the TX DMA channel!\n");
+ ret = -EINVAL;
+ goto err;
+ }
+
+ slave_config.direction = DMA_MEM_TO_DEV;
+ slave_config.dst_addr = spi_imx->mapbase + MXC_CSPITXDATA;
+ slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ slave_config.dst_maxburst = spi_imx_get_fifosize(spi_imx) / 2;
+ ret = dmaengine_slave_config(spi_imx->dma_chan_tx, &slave_config);
+ if (ret) {
+ dev_err(dev, "error in TX dma configuration.");
+ goto err;
+ }
+
+ /* Prepare for RX : */
+ spi_imx->dma_chan_rx = dma_request_slave_channel(dev, "rx");
+ if (!spi_imx->dma_chan_rx) {
+ dev_dbg(dev, "cannot get the DMA channel.\n");
+ ret = -EINVAL;
+ goto err;
+ }
+
+ slave_config.direction = DMA_DEV_TO_MEM;
+ slave_config.src_addr = spi_imx->mapbase + MXC_CSPIRXDATA;
+ slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ slave_config.src_maxburst = spi_imx_get_fifosize(spi_imx) / 2;
+ ret = dmaengine_slave_config(spi_imx->dma_chan_rx, &slave_config);
+ if (ret) {
+ dev_err(dev, "error in RX dma configuration.\n");
+ goto err;
+ }
+ spi_imx->dma_is_inited = 1;
+
+ return 0;
+err:
+ spi_imx_sdma_exit(spi_imx);
+ return ret;
+}
+
static int spi_imx_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
@@ -849,6 +1279,8 @@ static int spi_imx_probe(struct platform_device *pdev)
(struct spi_imx_devtype_data *) pdev->id_entry->driver_data;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res)
+ spi_imx->mapbase = res->start;
spi_imx->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(spi_imx->base)) {
ret = PTR_ERR(spi_imx->base);
@@ -890,6 +1322,9 @@ static int spi_imx_probe(struct platform_device *pdev)
spi_imx->spi_clk = clk_get_rate(spi_imx->clk_per);
+ spi_imx->dev = &pdev->dev;
+ spi_imx_sdma_init(spi_imx);
+
spi_imx->devtype_data->reset(spi_imx);
spi_imx->devtype_data->intctrl(spi_imx, 0);
--
1.7.8
More information about the linux-arm-kernel
mailing list