[PATCH 1/6] Basic Device Tree support for the at91sam9261
Jean-Jacques Hiblot
jjhiblot at traphandler.com
Fri Jan 3 04:52:04 EST 2014
2014/1/3 boris brezillon <b.brezillon at overkiz.com>:
> Hello JJ,
>
>
> On 31/12/2013 17:32, jjhiblot at traphandler.com wrote:
>>
>> From: jean-jacques hiblot <jean-jacques.hiblot at jdsu.com>
>>
>> This patch implements the basics to boot a at91sam9261ek with a dt-enabled
>> kernel (at91_dt_defconfig).
>> Only dbgu, nand and watchdog are described in the DT.
>>
>> Signed-off-by: Jean-Jacques Hiblot <jjhiblot at traphandler.com>
>> ---
>> arch/arm/boot/dts/at91sam9261.dtsi | 476
>> +++++++++++++++++++++++++++++++
>> arch/arm/boot/dts/at91sam9261ek.dts | 75 +++++
>> arch/arm/mach-at91/at91sam9261.c | 15 +
>> arch/arm/mach-at91/at91sam9261_devices.c | 18 ++
>
>
> Just a nitpick, but I guess it would be cleaner to split this patch:
> 1) add a91sam9261 dt SoC support
> 2) move at91sam9261ek board to dt
I'll split this patch for the next round.
>
>
>> 4 files changed, 584 insertions(+)
>> create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi
>> create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts
>>
>> diff --git a/arch/arm/boot/dts/at91sam9261.dtsi
>> b/arch/arm/boot/dts/at91sam9261.dtsi
>> new file mode 100644
>> index 0000000..ce23d7d
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91sam9261.dtsi
>> @@ -0,0 +1,476 @@
>> +/*
>> + * at91sam9261.dtsi - Device Tree Include file for AT91SAM9263 family SoC
>> + *
>> + * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot at traphandler.com>
>> + *
>> + * Licensed under GPLv2 only.
>> + */
>> +
>> +#include "skeleton.dtsi"
>> +#include <dt-bindings/pinctrl/at91.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +
>> +/ {
>> + model = "Atmel AT91SAM9261 family SoC";
>> + compatible = "atmel,at91sam9261";
>> + interrupt-parent = <&aic>;
>> +
>> + aliases {
>> + serial0 = &dbgu;
>> + serial1 = &usart0;
>> + serial2 = &usart1;
>> + serial3 = &usart2;
>> + gpio0 = &pioA;
>> + gpio1 = &pioB;
>> + gpio2 = &pioC;
>> + tcb0 = &tcb0;
>> + i2c0 = &i2c0;
>> + ssc0 = &ssc0;
>> + ssc1 = &ssc1;
>> + };
>> + cpus {
>> + #address-cells = <0>;
>> + #size-cells = <0>;
>> +
>> + cpu {
>> + compatible = "arm,arm926ej-s";
>> + device_type = "cpu";
>> + };
>> + };
>> +
>> + memory {
>> + reg = <0x20000000 0x08000000>;
>> + };
>> +
>> + ahb {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + apb {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + aic: interrupt-controller at fffff000 {
>> + #interrupt-cells = <3>;
>> + compatible = "atmel,at91rm9200-aic";
>> + interrupt-controller;
>> + reg = <0xfffff000 0x200>;
>> + atmel,external-irqs = <29 30 31>;
>> + };
>> +
>> + pmc: pmc at fffffc00 {
>> + compatible = "atmel,at91rm9200-pmc";
>> + reg = <0xfffffc00 0x100>;
>> + };
>> +
>> + ramc: ramc at ffffea00 {
>> + compatible = "atmel,at91sam9260-sdramc";
>> + reg = <0xffffea00 0x200>;
>> + };
>> +
>> + pit: timer at fffffd30 {
>> + compatible = "atmel,at91sam9260-pit";
>> + reg = <0xfffffd30 0xf>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + };
>> +
>> + tcb0: timer at fffa0000 {
>> + compatible = "atmel,at91rm9200-tcb";
>> + reg = <0xfffa0000 0x100>;
>> + interrupts = < 17 IRQ_TYPE_LEVEL_HIGH 0
>> + 18 IRQ_TYPE_LEVEL_HIGH 0
>> + 19 IRQ_TYPE_LEVEL_HIGH 0
>> + >;
>> + status = "disabled";
>> + };
>> +
>> + rstc at fffffd00 {
>> + compatible = "atmel,at91sam9260-rstc";
>> + reg = <0xfffffd00 0x10>;
>> + };
>> +
>> + shdwc at fffffd10 {
>> + compatible = "atmel,at91sam9260-shdwc";
>> + reg = <0xfffffd10 0x10>;
>> + };
>> +
>> + pinctrl at fffff400 {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + compatible = "atmel,at91rm9200-pinctrl",
>> "simple-bus";
>> + ranges = <0xfffff400 0xfffff400 0xa00>;
>> +
>> + atmel,mux-mask = <
>> + /* A B */
>> + 0xffffffff 0xfffffff7 /* pioA */
>> + 0xffffffff 0xfffffff4 /* pioB */
>> + 0xffffffff 0xffffff07 /* pioC */
>> + >;
>> +
>> + /* shared pinctrl settings */
>> + dbgu {
>> + pinctrl_dbgu: dbgu-0 {
>> + atmel,pins =
>> + <AT91_PIOA 9
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PA9 periph A */
>> + AT91_PIOA 10
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PA10 periph A with pullup */
>> + };
>> + };
>> +
>> + usart0 {
>> + pinctrl_usart0: usart0-0 {
>> + atmel,pins =
>> + <AT91_PIOC 8
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC8 periph A with pullup */
>> + AT91_PIOC 9
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC9 periph A */
>> + };
>> +
>> + pinctrl_usart0_rts: usart0_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOC 10
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC10 periph A */
>> + };
>> +
>> + pinctrl_usart0_cts: usart0_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOC 11
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC11 periph A */
>> + };
>> + };
>> +
>> + usart1 {
>> + pinctrl_usart1: usart1-0 {
>> + atmel,pins =
>> + <AT91_PIOC 12
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC12 periph A with pullup */
>> + AT91_PIOC 13
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC13 periph A */
>> + };
>> +
>> + pinctrl_usart1_rts: usart1_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 12
>> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA12 periph B */
>> + };
>> +
>> + pinctrl_usart1_cts: usart1_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 13
>> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA13 periph B */
>> + };
>> + };
>> +
>> + usart2 {
>> + pinctrl_usart2: usart2-0 {
>> + atmel,pins =
>> + <AT91_PIOC 14
>> AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PC14 periph A with pullup */
>> + AT91_PIOC 15
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PC15 periph A */
>> + };
>> +
>> + pinctrl_usart2_rts: usart2_rts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 15
>> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA15 periph B */
>> + };
>> +
>> + pinctrl_usart2_cts: usart2_cts-0 {
>> + atmel,pins =
>> + <AT91_PIOA 16
>> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA16 periph B */
>> + };
>> + };
>> +
>> + nand {
>> + pinctrl_nand: nand-0 {
>> + atmel,pins =
>> + <AT91_PIOC 15
>> AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PC15 gpio RDY pin pull_up*/
>> + AT91_PIOC 14
>> AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PC14 gpio enable pin pull_up */
>> + };
>> + };
>> +
>> + mmc0 {
>> + pinctrl_mmc0_clk: mmc0_clk-0 {
>> + atmel,pins =
>> + <AT91_PIOA 2
>> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA2 periph B */
>> + };
>> +
>> + pinctrl_mmc0_slot0_cmd_dat0:
>> mmc0_slot0_cmd_dat0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 1
>> AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA1 periph B with pullup */
>> + AT91_PIOA 0
>> AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA0 periph B with pullup */
>> + };
>> +
>> + pinctrl_mmc0_slot0_dat1_3:
>> mmc0_slot0_dat1_3-0 {
>> + atmel,pins =
>> + <AT91_PIOA 4
>> AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA4 periph B with pullup */
>> + AT91_PIOA 5
>> AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA5 periph B with pullup */
>> + AT91_PIOA 6
>> AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA6 periph B with pullup */
>> + };
>> + };
>> +
>> + ssc0 {
>> + pinctrl_ssc0_tx: ssc0_tx-0 {
>> + atmel,pins =
>> + <AT91_PIOB 21
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PB21 periph A */
>> + AT91_PIOB 22
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PB22 periph A */
>> + AT91_PIOB 23
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB23 periph A */
>> + };
>> +
>> + pinctrl_ssc0_rx: ssc0_rx-0 {
>> + atmel,pins =
>> + <AT91_PIOB 24
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PB24 periph A */
>> + AT91_PIOB 25
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PB25 periph A */
>> + AT91_PIOB 26
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB26 periph A */
>> + };
>> + };
>> +
>> + ssc1 {
>> + pinctrl_ssc1_tx: ssc1_tx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 17
>> AT91_PERIPH_B AT91_PINCTRL_NONE /* PA17 periph B */
>> + AT91_PIOA 18
>> AT91_PERIPH_B AT91_PINCTRL_NONE /* PA18 periph B */
>> + AT91_PIOA 19
>> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA19 periph B */
>> + };
>> +
>> + pinctrl_ssc1_rx: ssc1_rx-0 {
>> + atmel,pins =
>> + <AT91_PIOA 20
>> AT91_PERIPH_B AT91_PINCTRL_NONE /* PA20 periph B */
>> + AT91_PIOA 21
>> AT91_PERIPH_B AT91_PINCTRL_NONE /* PA21 periph B */
>> + AT91_PIOA 22
>> AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PA22 periph B */
>> + };
>> + };
>> +
>> + spi0 {
>> + pinctrl_spi0: spi0-0 {
>> + atmel,pins =
>> + <AT91_PIOA 0
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PA0 periph A SPI0_MISO pin */
>> + AT91_PIOA 1
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PA1 periph A SPI0_MOSI pin */
>> + AT91_PIOA 2
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PA2 periph A SPI0_SPCK pin */
>> + };
>> + };
>> +
>> + spi1 {
>> + pinctrl_spi1: spi1-0 {
>> + atmel,pins =
>> + <AT91_PIOB 30
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PB30 periph A SPI1_MISO pin */
>> + AT91_PIOB 31
>> AT91_PERIPH_A AT91_PINCTRL_NONE /* PB31 periph A SPI1_MOSI pin */
>> + AT91_PIOB 29
>> AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB29 periph A SPI1_SPCK pin */
>> + };
>> + };
>> +
>> + tcb0 {
>> + pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
>> + atmel,pins = <AT91_PIOC 16
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tclk1: tcb0_tclk1-0 {
>> + atmel,pins = <AT91_PIOC 17
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tclk2: tcb0_tclk2-0 {
>> + atmel,pins = <AT91_PIOC 18
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa0: tcb0_tioa0-0 {
>> + atmel,pins = <AT91_PIOC 19
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa1: tcb0_tioa1-0 {
>> + atmel,pins = <AT91_PIOC 21
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tioa2: tcb0_tioa2-0 {
>> + atmel,pins = <AT91_PIOC 23
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob0: tcb0_tiob0-0 {
>> + atmel,pins = <AT91_PIOC 20
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob1: tcb0_tiob1-0 {
>> + atmel,pins = <AT91_PIOC 22
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> +
>> + pinctrl_tcb0_tiob2: tcb0_tiob2-0 {
>> + atmel,pins = <AT91_PIOC 24
>> AT91_PERIPH_B AT91_PINCTRL_NONE>;
>> + };
>> + };
>> +
>> + pioA: gpio at fffff400 {
>> + compatible =
>> "atmel,at91rm9200-gpio";
>> + reg = <0xfffff400 0x200>;
>> + interrupts = <2
>> IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + pioB: gpio at fffff600 {
>> + compatible =
>> "atmel,at91rm9200-gpio";
>> + reg = <0xfffff600 0x200>;
>> + interrupts = <3
>> IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> +
>> + pioC: gpio at fffff800 {
>> + compatible =
>> "atmel,at91rm9200-gpio";
>> + reg = <0xfffff800 0x200>;
>> + interrupts = <4
>> IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + };
>> + };
>> +
>> + dbgu: serial at fffff200 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffff200 0x200>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_dbgu>;
>> + status = "disabled";
>> + };
>> +
>> + usart0: serial at fffb0000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb0000 0x200>;
>> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart0>;
>> + status = "disabled";
>> + };
>> +
>> + usart1: serial at ffffb400 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb4000 0x200>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart1>;
>> + status = "disabled";
>> + };
>> +
>> + usart2: serial at fff94000 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffb8000 0x200>;
>> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
>> + atmel,use-dma-rx;
>> + atmel,use-dma-tx;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_usart2>;
>> + status = "disabled";
>> + };
>> +
>> + ssc0: ssc at fffbc000 {
>> + compatible = "atmel,at91rm9200-ssc";
>> + reg = <0xfffbc000 0x4000>;
>> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ssc0_tx
>> &pinctrl_ssc0_rx>;
>> + status = "disabled";
>> + };
>> +
>> + ssc1: ssc at fffc0000 {
>> + compatible = "atmel,at91rm9200-ssc";
>> + reg = <0xfffc0000 0x4000>;
>> + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ssc1_tx
>> &pinctrl_ssc1_rx>;
>> + status = "disabled";
>> + };
>> +
>> + usb1: gadget at fffa4000 {
>> + compatible = "atmel,at91rm9200-udc";
>> + reg = <0xfffa4000 0x4000>;
>> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>;
>> + status = "disabled";
>> + };
>> +
>> + i2c0: i2c at fffac000 {
>> + compatible = "atmel,at91sam9261-i2c";
>> + reg = <0xfffac000 0x100>;
>> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + mmc0: mmc at fffa8000 {
>> + compatible = "atmel,hsmci";
>> + reg = <0xfffa8000 0x600>;
>> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + watchdog at fffffd40 {
>> + compatible = "atmel,at91sam9260-wdt";
>> + reg = <0xfffffd40 0x10>;
>> + status = "disabled";
>> + };
>> +
>> + spi0: spi at fffc8000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "atmel,at91rm9200-spi";
>> + reg = <0xfffc8000 0x200>;
>> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_spi0>;
>> + status = "disabled";
>> + };
>> +
>> + spi1: spi at fffcc000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "atmel,at91rm9200-spi";
>> + reg = <0xfffcc000 0x200>;
>> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_spi1>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + nand0: nand at 40000000 {
>> + compatible = "atmel,at91rm9200-nand";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + reg = <0x40000000 0x10000000>;
>> + atmel,nand-addr-offset = <22>;
>> + atmel,nand-cmd-offset = <21>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_nand>;
>> +
>> + gpios = <&pioC 15 GPIO_ACTIVE_HIGH
>> + &pioC 14 GPIO_ACTIVE_HIGH
>> + 0
>> + >;
>> + status = "disabled";
>> + };
>> +
>> + usb0: ohci at 00500000 {
>> + compatible = "atmel,at91rm9200-ohci", "usb-ohci";
>> + reg = <0x00500000 0x100000>;
>> + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + i2c at 0 {
>> + compatible = "i2c-gpio";
>> + gpios = <&pioA 7 GPIO_ACTIVE_HIGH /* sda */
>> + &pioA 8 GPIO_ACTIVE_HIGH /* scl */
>> + >;
>> + i2c-gpio,sda-open-drain;
>> + i2c-gpio,scl-open-drain;
>> + i2c-gpio,delay-us = <2>; /* ~100 kHz */
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +};
>> diff --git a/arch/arm/boot/dts/at91sam9261ek.dts
>> b/arch/arm/boot/dts/at91sam9261ek.dts
>> new file mode 100644
>> index 0000000..f3d22a9
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91sam9261ek.dts
>> @@ -0,0 +1,75 @@
>> +/*
>> + * at91sam9261ek.dts - Device Tree file for Atmel at91sam9261 reference
>> board
>> + *
>> + * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot at traphandler.com>
>> + *
>> + * Licensed under GPLv2 only.
>> + */
>> +/dts-v1/;
>> +#include "at91sam9261.dtsi"
>> +
>> +/ {
>> + model = "Atmel at91sam9261ek";
>> + compatible = "atmel,at91sam9261ek", "atmel,at91sam9261",
>> "atmel,at91sam9";
>> +
>> + chosen {
>> + bootargs = "mem=64M console=ttyS0,115200";
>> + };
>> +
>> + memory {
>> + reg = <0x20000000 0x4000000>;
>> + };
>> +
>> + clocks {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + main_clock: clock at 0 {
>> + compatible = "atmel,osc", "fixed-clock";
>> + clock-frequency = <18432000>;
>> + };
>> + };
>> +
>> + ahb {
>> + apb {
>> + dbgu: serial at fffff200 {
>> + status = "okay";
>> + };
>> +
>> + watchdog at fffffd40 {
>> + status = "okay";
>> + };
>> + };
>> +
>> + nand0: nand at 40000000 {
>> + nand-bus-width = <8>;
>> + nand-ecc-mode = "soft";
>> + nand-on-flash-bbt = <1>;
>> + status = "okay";
>> + at91bootstrap at 0 {
>> + label = "at91bootstrap";
>> + reg = <0x0 0x20000>;
>> + };
>> + };
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + ds8 {
>> + label = "ds8";
>> + gpios = <&pioA 13 GPIO_ACTIVE_LOW>;
>> + linux,default-trigger = "none";
>> + };
>> + ds7 {
>> + label = "ds7";
>> + gpios = <&pioA 14 GPIO_ACTIVE_LOW>;
>> + linux,default-trigger = "nand-disk";
>> + };
>> + ds1 {
>> + label = "ds1";
>> + gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
>> + linux,default-trigger = "heartbeat";
>> + };
>> + };
>> +};
>
>
> Didn't you forget the at91sam9261ek entry in arch/arm/boot/dts/Makefile ?
Indeed I did forget
>
>
>> diff --git a/arch/arm/mach-at91/at91sam9261.c
>> b/arch/arm/mach-at91/at91sam9261.c
>> index 6276b4c..200d17a 100644
>> --- a/arch/arm/mach-at91/at91sam9261.c
>> +++ b/arch/arm/mach-at91/at91sam9261.c
>> @@ -189,6 +189,21 @@ static struct clk_lookup periph_clocks_lookups[] = {
>> CLKDEV_CON_ID("pioA", &pioA_clk),
>> CLKDEV_CON_ID("pioB", &pioB_clk),
>> CLKDEV_CON_ID("pioC", &pioC_clk),
>> + /* more usart lookup table for DT entries */
>> + CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
>> + CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),
>> + CLKDEV_CON_DEV_ID("usart", "ffffb400.serial", &usart1_clk),
>> + CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk),
>> + /* more tc lookup table for DT entries */
>> + CLKDEV_CON_DEV_ID("t0_clk", "fffa0000.timer", &tc0_clk),
>> + CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &ohci_clk),
>> + CLKDEV_CON_DEV_ID("spi_clk", "fffc8000.spi", &spi0_clk),
>> + CLKDEV_CON_DEV_ID("spi_clk", "fffcc000.spi", &spi1_clk),
>> + CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffac000.i2c", &twi_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
>> + CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
>> };
>>
>
> It would be great if you could add dt clk support to at91sam9261 SoC :) (see
> https://github.com/at91linux/linux-at91/blob/bbr/at91-3.14-clk/arch/arm/boot/dts/at91sam9x5.dtsi#L87).
> But this is antoher story... ;)
This is just a start :o) There is a lot of room for improvement.
>
>
>> static struct clk_lookup usart_clocks_lookups[] = {
>> diff --git a/arch/arm/mach-at91/at91sam9261_devices.c
>> b/arch/arm/mach-at91/at91sam9261_devices.c
>> index b2a3474..2f926d9 100644
>> --- a/arch/arm/mach-at91/at91sam9261_devices.c
>> +++ b/arch/arm/mach-at91/at91sam9261_devices.c
>> @@ -599,8 +599,23 @@ static struct platform_device at91sam9261_tcb_device
>> = {
>> .num_resources = ARRAY_SIZE(tcb_resources),
>> };
>>
>> +#if defined(CONFIG_OF)
>> +static struct of_device_id tcb_ids[] = {
>> + { .compatible = "atmel,at91rm9200-tcb" },
>> + { /*sentinel*/ }
>> +};
>> +#endif
>> static void __init at91_add_device_tc(void)
>> {
>> +#if defined(CONFIG_OF)
>> + struct device_node *np;
>> +
>> + np = of_find_matching_node(NULL, tcb_ids);
>> + if (np) {
>> + of_node_put(np);
>> + return;
>> + }
>> +#endif
>
>
> Why do you need this ?
> Isn't this already skipped by the following test
> (if(of_have_populated_dt())) ?
>
Actually I tried to match closely the 9263 and this part comes from
the 9263 code. This comes from
4abb367722c2dc06972658c8fad5b4763114477c which brings dt support to
the 9263. I didn't undertsand it, but include it anyway. I'll remove
this.
>
>> platform_device_register(&at91sam9261_tcb_device);
>> }
>> #else
>> @@ -1088,6 +1103,9 @@ void __init at91_add_device_serial(void) {}
>> */
>> static int __init at91_add_standard_devices(void)
>> {
>> + if (of_have_populated_dt())
>> + return 0;
>> +
>> at91_add_device_rtt();
>> at91_add_device_watchdog();
>> at91_add_device_tc();
>>
>
> Best Regards,
>
> Boris
More information about the linux-arm-kernel
mailing list