[PATCH v2 4/4] mmc: sdhci: host: add new f_sdh30
Ulf Hansson
ulf.hansson at linaro.org
Tue Dec 30 05:53:11 PST 2014
On 15 December 2014 at 08:30, Vincent Yang
<vincent.yang.fujitsu at gmail.com> wrote:
> This patch adds new host controller driver for
> Fujitsu SDHCI controller f_sdh30.
>
> Signed-off-by: Andy Green <andy.green at linaro.org>
> Signed-off-by: Vincent Yang <Vincent.Yang at tw.fujitsu.com>
> Signed-off-by: Tetsuya Takinishi <t.takinishi at jp.fujitsu.com>
> ---
> .../devicetree/bindings/mmc/sdhci-fujitsu.txt | 35 +++
> drivers/mmc/host/Kconfig | 8 +
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/sdhci_f_sdh30.c | 319 +++++++++++++++++++++
> 4 files changed, 363 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c
>
> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> new file mode 100644
> index 0000000..d1a50f1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> @@ -0,0 +1,35 @@
> +* Fujitsu SDHCI controller
> +
> +This file documents differences between the core properties in mmc.txt
> +and the properties used by the sdhci_f_sdh30 driver.
> +
> +Required properties:
> +- compatible: "fujitsu,mb86s70-sdhci-3.0"
> +- voltage-ranges : This is a list of pairs. In each pair, two cells
> + are required. First cell specifies minimum slot voltage (mV), second
> + cell specifies maximum slot voltage (mV). In case of supported voltage
> + range is discontinuous, several ranges could be specified as a list.
Can't these be modelled from a regulator instead? Thus using a "vmmc-supply"?
> +
> +Optional properties:
> +- vqmmc-supply: phandle to the regulator device tree node, mentioned
> + as the VCCQ/VDD_IO supply in the eMMC/SD specs.
> +- clocks: Must contain an entry for each entry in clock-names. It is a
> + list of phandles and clock-specifier pairs.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Should contain the following two entries:
> + "iface" - clock used for sdhci interface
> + "core" - core clock for sdhci controller
> +
> +Example:
> +
> + sdhci1: mmc at 36600000 {
> + compatible = "fujitsu,mb86s70-sdhci-3.0";
> + reg = <0 0x36600000 0x1000>;
> + interrupts = <0 172 0x4>,
> + <0 173 0x4>;
> + voltage-ranges = <1800 1800>, <3300 3300>;
> + bus-width = <4>;
> + vqmmc-supply = <&vccq_sdhci1>;
> + clocks = <&clock 2 2 0>, <&clock 2 3 0>;
> + clock-names = "iface", "core";
> + };
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 2d6fbdd..288dcc3 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -290,6 +290,14 @@ config MMC_SDHCI_BCM2835
> This selects the BCM2835 SD/MMC controller. If you have a BCM2835
> platform with SD or MMC devices, say Y or M here.
>
> +config MMC_SDHCI_F_SDH30
> + tristate "SDHCI support for Fujitsu Semiconductor F_SDH30"
> + depends on MMC_SDHCI_PLTFM
> + depends on OF
> + help
> + This selects the Secure Digital Host Controller Interface (SDHCI)
> + Needed by some Fujitsu SoC for MMC / SD / SDIO support.
> + If you have a controller with this interface, say Y or M here.
> If unsure, say N.
>
> config MMC_MOXART
> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
> index f7b0a77..6a7cfe0 100644
> --- a/drivers/mmc/host/Makefile
> +++ b/drivers/mmc/host/Makefile
> @@ -16,6 +16,7 @@ obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
> obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o
> obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
> obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o
> +obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o
> obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
> obj-$(CONFIG_MMC_WBSD) += wbsd.o
> obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
> diff --git a/drivers/mmc/host/sdhci_f_sdh30.c b/drivers/mmc/host/sdhci_f_sdh30.c
> new file mode 100644
> index 0000000..76df115
> --- /dev/null
> +++ b/drivers/mmc/host/sdhci_f_sdh30.c
> @@ -0,0 +1,319 @@
> +/*
> + * linux/drivers/mmc/host/sdhci_f_sdh30.c
> + *
> + * Copyright (C) 2013 - 2014 Fujitsu Semiconductor, Ltd
> + * Vincent Yang <vincent.yang at tw.fujitsu.com>
> + * Copyright (C) 2014 Linaro Ltd Andy Green <andy.green at linaro.org>
> + *
> + * This program is free software: you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation, version 2 of the License.
> + */
> +
> +#include <linux/err.h>
> +#include <linux/delay.h>
> +#include <linux/module.h>
> +#include <linux/mmc/sd.h>
> +#include <linux/mmc/host.h>
> +#include <linux/mmc/card.h>
> +#include <linux/gpio.h>
> +#include <linux/of_gpio.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/suspend.h>
> +
> +#include "sdhci.h"
> +#include "sdhci-pltfm.h"
> +
> +/* F_SDH30 extended Controller registers */
> +#define F_SDH30_AHB_CONFIG 0x100
> +#define F_SDH30_AHB_BIGED 0x00000040
> +#define F_SDH30_BUSLOCK_DMA 0x00000020
> +#define F_SDH30_BUSLOCK_EN 0x00000010
> +#define F_SDH30_SIN 0x00000008
> +#define F_SDH30_AHB_INCR_16 0x00000004
> +#define F_SDH30_AHB_INCR_8 0x00000002
> +#define F_SDH30_AHB_INCR_4 0x00000001
> +
> +#define F_SDH30_TUNING_SETTING 0x108
> +#define F_SDH30_CMD_CHK_DIS 0x00010000
> +
> +#define F_SDH30_IO_CONTROL2 0x114
> +#define F_SDH30_CRES_O_DN 0x00080000
> +#define F_SDH30_MSEL_O_1_8 0x00040000
> +
> +#define F_SDH30_ESD_CONTROL 0x124
> +#define F_SDH30_EMMC_RST 0x00000002
> +#define F_SDH30_EMMC_HS200 0x01000000
> +
> +#define F_SDH30_CMD_DAT_DELAY 0x200
> +
> +#define F_SDH30_MIN_CLOCK 400000
> +
> +struct f_sdhost_priv {
> + struct clk *clk_iface;
> + struct clk *clk;
> + u32 vendor_hs200;
> + struct device *dev;
> +};
> +
> +void sdhci_f_sdh30_soft_voltage_switch(struct sdhci_host *host)
> +{
> + struct f_sdhost_priv *priv = sdhci_priv(host);
> + u32 ctrl = 0;
> +
> + usleep_range(2500, 3000);
> + ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2);
> + ctrl |= F_SDH30_CRES_O_DN;
> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
> + ctrl |= F_SDH30_MSEL_O_1_8;
> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
> +
> + ctrl &= ~F_SDH30_CRES_O_DN;
> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2);
> + usleep_range(2500, 3000);
> +
> + if (priv->vendor_hs200) {
> + dev_info(priv->dev, "%s: setting hs200\n", __func__);
> + ctrl = sdhci_readl(host, F_SDH30_ESD_CONTROL);
> + ctrl |= priv->vendor_hs200;
> + sdhci_writel(host, ctrl, F_SDH30_ESD_CONTROL);
> + }
> +
> + ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING);
> + ctrl |= F_SDH30_CMD_CHK_DIS;
> + sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING);
> +}
> +
> +unsigned int sdhci_f_sdh30_get_min_clock(struct sdhci_host *host)
> +{
> + return F_SDH30_MIN_CLOCK;
> +}
> +
> +void sdhci_f_sdh30_reset(struct sdhci_host *host, u8 mask)
> +{
> + if (sdhci_readw(host, SDHCI_CLOCK_CONTROL) == 0)
> + sdhci_writew(host, 0xBC01, SDHCI_CLOCK_CONTROL);
> +
> + sdhci_reset(host, mask);
> +}
> +
> +static const struct sdhci_ops sdhci_f_sdh30_ops = {
> + .voltage_switch = sdhci_f_sdh30_soft_voltage_switch,
> + .get_min_clock = sdhci_f_sdh30_get_min_clock,
> + .reset = sdhci_f_sdh30_reset,
> + .set_clock = sdhci_set_clock,
> + .set_bus_width = sdhci_set_bus_width,
> + .set_uhs_signaling = sdhci_set_uhs_signaling,
> +};
> +
> +static int sdhci_f_sdh30_probe(struct platform_device *pdev)
> +{
> + struct sdhci_host *host;
> + struct device *dev = &pdev->dev;
> + int irq, ctrl = 0, ret = 0;
> + struct f_sdhost_priv *priv;
> + u32 reg = 0;
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0) {
> + dev_err(dev, "%s: no irq specified\n", __func__);
> + ret = irq;
> + goto err;
> + }
> +
> + host = sdhci_alloc_host(dev, sizeof(struct sdhci_host) +
> + sizeof(struct f_sdhost_priv));
> + if (IS_ERR(host)) {
> + dev_err(dev, "%s: host allocate error\n", __func__);
No need to print this, already done via kzalloc().
> + ret = -ENOMEM;
> + goto err;
> + }
> + priv = sdhci_priv(host);
> + priv->dev = dev;
> +
> + host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
> + SDHCI_QUIRK_INVERTED_WRITE_PROTECT;
> + host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE |
> + SDHCI_QUIRK2_TUNING_WORK_AROUND;
> +
> + ret = mmc_of_parse(host->mmc);
> + if (ret)
> + goto err_of_parse;
> +
> + ret = mmc_of_parse_voltage(pdev->dev.of_node, &host->ocr_mask);
> + if (ret)
> + goto err_of_parse;
> +
> + platform_set_drvdata(pdev, host);
> +
> + sdhci_get_of_property(pdev);
> + host->hw_name = "f_sdh30";
> + host->ops = &sdhci_f_sdh30_ops;
> + host->irq = irq;
> +
> + host->ioaddr = of_iomap(pdev->dev.of_node, 0);
How about using devm_ioremap_resource()?
> + if (!host->ioaddr) {
> + dev_err(dev, "%s: failed to remap registers\n", __func__);
> + ret = -ENXIO;
> + goto err_remap;
> + }
> +
> + priv->clk_iface = clk_get(&pdev->dev, "iface");
devm_clk_get()
> + if (!IS_ERR(priv->clk_iface)) {
> + ret = clk_prepare_enable(priv->clk_iface);
> + if (ret < 0) {
> + dev_err(dev, "Failed to enable iface clock: %d\n", ret);
> + goto err_clk1;
> + }
> + }
> + priv->clk = clk_get(&pdev->dev, "core");
devm_clk_get()
> + if (!IS_ERR(priv->clk)) {
> + ret = clk_prepare_enable(priv->clk);
> + if (ret < 0) {
> + dev_err(dev, "Failed to enable core clock: %d\n", ret);
> + goto err_clk2;
> + }
> + }
> +
> +#ifdef CONFIG_PM_RUNTIME
Remove this #ifdef.
> + pm_runtime_set_active(&pdev->dev);
> + pm_runtime_enable(&pdev->dev);
> + ret = pm_runtime_get_sync(&pdev->dev);
Why do a pm_runtime_get_sync() without a balanced call to
pm_runtime_put()? That will keep the device forever runtime PM
resumed.
> + if (ret < 0)
> + dev_err(dev, "Failed to pm_runtime_get_sync: %d\n", ret);
> +#endif
> +
> + ret = sdhci_add_host(host);
> + if (ret) {
> + dev_err(dev, "%s: host add error\n", __func__);
> + goto err_add_host;
> + }
> +
> + /* init vendor specific regs */
All this vendor specfic stuff must be done prior you invoke
sdhci_add_host(), otherwise you will start the card initialization
before this driver is fully probed.
> + ctrl = sdhci_readw(host, F_SDH30_AHB_CONFIG);
> + ctrl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 |
> + F_SDH30_AHB_INCR_4;
> + ctrl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN);
> + sdhci_writew(host, ctrl, F_SDH30_AHB_CONFIG);
> +
> + reg = sdhci_readl(host, F_SDH30_ESD_CONTROL);
> + sdhci_writel(host, reg & ~F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL);
> + msleep(20);
> + sdhci_writel(host, reg | F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL);
> +
> + reg = sdhci_readl(host, SDHCI_CAPABILITIES);
> + if (reg & SDHCI_CAN_DO_8BIT)
> + priv->vendor_hs200 = F_SDH30_EMMC_HS200;
> + else
> + priv->vendor_hs200 = 0;
> +
> + return 0;
> +
> +err_add_host:
> + clk_put(priv->clk);
> +err_clk2:
> + clk_put(priv->clk_iface);
> +err_clk1:
> + iounmap(host->ioaddr);
> +err_remap:
> +err_of_parse:
> + sdhci_free_host(host);
> +err:
> + return ret;
If you use the devm_* managed functions as I pointed out above, this
error handling will be greatly simplified.
> +}
> +
> +static int sdhci_f_sdh30_remove(struct platform_device *pdev)
> +{
> + struct sdhci_host *host = platform_get_drvdata(pdev);
> + struct f_sdhost_priv *priv = sdhci_priv(host);
> + struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +
Don't forget to handle runtime PM here. You probably would like this:
pm_runtime_get_sync()
pm_runtime_disable()
pm_runtime_put_noidle()
> + sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) ==
> + 0xffffffff);
> + iounmap(host->ioaddr);
> + release_mem_region(iomem->start, resource_size(iomem));
> +
> + clk_disable_unprepare(priv->clk_iface);
> + clk_disable_unprepare(priv->clk);
> +
> + clk_put(priv->clk);
> + clk_put(priv->clk_iface);
> +
> + sdhci_free_host(host);
> + platform_set_drvdata(pdev, NULL);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int sdhci_f_sdh30_suspend(struct device *dev)
> +{
> + struct sdhci_host *host = dev_get_drvdata(dev);
> +
> + return sdhci_suspend_host(host);
> +}
> +
> +static int sdhci_f_sdh30_resume(struct device *dev)
> +{
> + struct sdhci_host *host = dev_get_drvdata(dev);
> +
> + return sdhci_resume_host(host);
> +}
> +#endif
> +
> +#ifdef CONFIG_PM_RUNTIME
->CONFIG_PM
> +static int sdhci_f_sdh30_runtime_suspend(struct device *dev)
> +{
> + struct sdhci_host *host = dev_get_drvdata(dev);
> +
> + return sdhci_runtime_suspend_host(host);
> +}
> +
> +static int sdhci_f_sdh30_runtime_resume(struct device *dev)
> +{
> + struct sdhci_host *host = dev_get_drvdata(dev);
> +
> + return sdhci_runtime_resume_host(host);
> +}
> +#endif
> +
> +#ifdef CONFIG_PM
Remove #ifdef
> +static const struct dev_pm_ops sdhci_f_sdh30_pmops = {
> + SET_SYSTEM_SLEEP_PM_OPS(sdhci_f_sdh30_suspend, sdhci_f_sdh30_resume)
> + SET_RUNTIME_PM_OPS(sdhci_f_sdh30_runtime_suspend,
> + sdhci_f_sdh30_runtime_resume, NULL)
> +};
> +
> +#define SDHCI_F_SDH30_PMOPS (&sdhci_f_sdh30_pmops)
Remove this and use &sdhci_f_sdh30_pmops directly below instead.
> +
> +#else
> +#define SDHCI_F_SDH30_PMOPS NULL
> +#endif
> +
> +static const struct of_device_id f_sdh30_dt_ids[] = {
> + { .compatible = "fujitsu,mb86s70-sdhci-3.0" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, f_sdh30_dt_ids);
> +
> +static struct platform_driver sdhci_f_sdh30_driver = {
> + .driver = {
> + .name = "f_sdh30",
> + .of_match_table = f_sdh30_dt_ids,
> +#ifdef CONFIG_PM_SLEEP
> + .pm = SDHCI_F_SDH30_PMOPS,
> +#endif
> + },
> + .probe = sdhci_f_sdh30_probe,
> + .remove = sdhci_f_sdh30_remove,
> +};
> +
> +module_platform_driver(sdhci_f_sdh30_driver);
> +
> +MODULE_DESCRIPTION("F_SDH30 SD Card Controller driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("FUJITSU SEMICONDUCTOR LTD.");
> +MODULE_ALIAS("platform:f_sdh30");
> --
> 1.9.0
>
Kind regards
Uffe
More information about the linux-arm-kernel
mailing list