[PATCH 3/3] ARM: mvebu: Add Armada 385 General Purpose Development Board support

[Andrew Lunn]

> @@ -0,0 +1,380 @@
> +/*
> + * Device Tree file for Marvell Armada 385 development board
> + * (RD-88F6820-GP)
> + *
> + * Copyright (C) 2014 Marvell
> + *
> + * Gregory CLEMENT <gregory.clement at free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is licensed under the terms of the GNU General Public
> + *     License version 2.  This program is licensed "as is" without
> + *     any warranty of any kind, whether express or implied.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "armada-385.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "Marvell Armada 385 GP";
> +	compatible = "marvell,a385-gp", "marvell,armada385", "marvell,armada380";
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200 earlyprintk";
> +	};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x80000000>; /* 2 GB */
> +	};
> +
> +	soc {
> +		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> +			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
> +
> +		internal-regs {
> +			spi at 10600 {
> +				status = "okay";
> +
> +				spi-flash at 0 {
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +					compatible = "st,m25p128";
> +					reg = <0>; /* Chip select 0 */
> +					spi-max-frequency = <50000000>;
> +					m25p,fast-read;
> +				};
> +			};
> +
> +			i2c at 11000 {
> +				status = "okay";
> +				clock-frequency = <100000>;
> +
> +				pca9555_0: pca9555 at 20 {

I think Sebastian will come along and ask this is called gpio, not
pca9555_0. See the review he made of the Seagate Black NAS box.

> +					compatible = "nxp,pca9555";
> +					pinctrl-names = "default";
> +					pinctrl-0 = <&pca0_pins>;
> +					interrupt-parent = <&gpio0>;
> +					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
> +					gpio-controller;
> +					#gpio-cells = <2>;
> +					interrupt-controller;
> +					#interrupt-cells = <2>;
> +					reg = <0x20>;
> +				};
> +
> +				pca9555_1: pca9555 at 21 {
> +					compatible = "nxp,pca9555";
> +					pinctrl-names = "default";
> +					interrupt-parent = <&gpio0>;
> +					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
> +
> +					gpio-controller;
> +					#gpio-cells = <2>;
> +					interrupt-controller;
> +					#interrupt-cells = <2>;
> +

Maybe remove the blank lines here, to make it similar to the previous
one?

> +					reg = <0x21>;
> +				};
> +

Maybe remove this blank line?

> +			};
> +
> +			serial at 12000 {
> +				status = "okay";
> +			};

It would be nice if you can document the connector number and the
pinout of the serial port, if it is not on the silk screen.

> +
> +			ethernet at 30000 {
> +				status = "okay";
> +				phy = <&phy0>;
> +				phy-mode = "rgmii-id";
> +			};
> +
> +			usb at 50000 {
> +				vcc-supply = <&reg_usb2_0_vbus>;
> +				status = "okay";
> +			};
> +
> +			ethernet at 70000 {
> +				status = "okay";
> +				phy = <&phy1>;
> +				phy-mode = "rgmii-id";
> +			};
> +
> +
> +			mdio at 72004 {
> +				phy0: ethernet-phy at 0 {
> +					reg = <0>;
> +				};
> +
> +				phy1: ethernet-phy at 1 {
> +					reg = <1>;
> +				};
> +			};
> +
> +			sata at a8000 {
> +				nr-ports = <2>;
> +				status = "okay";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				sata0: sata-port at 0 {
> +					reg = <0>;
> +					target-supply = <&reg_5v_sata0>;
> +				};
> +
> +				sata1: sata-port at 1 {
> +					reg = <1>;
> +					target-supply = <&reg_5v_sata1>;
> +				};
> +			};
> +
> +			sata at e0000 {
> +				nr-ports = <2>;
> +				status = "okay";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				sata2: sata-port at 0 {
> +					reg = <0>;
> +					target-supply = <&reg_5v_sata2>;
> +				};
> +
> +				sata3: sata-port at 1 {
> +					reg = <1>;
> +					target-supply = <&reg_5v_sata3>;
> +				};
> +			};
> +
> +			sdhci at d8000 {
> +				clock-frequency = <200000000>;
> +				cd-gpios = <&pca9555_0 5 GPIO_ACTIVE_LOW>;
> +				no-1-8-v;
> +				wp-inverted;
> +				bus-width = <8>;
> +				status = "okay";
> +			};
> +
> +			usb3 at f0000 {
> +				vcc-supply = <&reg_usb2_1_vbus>;
> +				status = "okay";
> +			};
> +
> +			usb3 at f8000 {
> +				vcc-supply = <&reg_usb3_vbus>;
> +				status = "okay";
> +			};
> +		};
> +
> +		pcie-controller {
> +			status = "okay";
> +			/*
> +			 * One PCIe units is accessible through
> +			 * standard PCIe slot on the board.
> +			 */
> +			pcie at 1,0 {
> +				/* Port 0, Lane 0 */
> +				status = "okay";
> +			};
> +
> +			/*
> +			 * The two other PCIe units are accessible
> +			 * through mini PCIe slot on the board.
> +			 */
> +			pcie at 2,0 {
> +				/* Port 1, Lane 0 */
> +				status = "okay";
> +			};
> +			pcie at 3,0 {
> +				/* Port 2, Lane 0 */
> +				status = "okay";
> +			};
> +		};
> +
> +		gpio-fan {
> +			compatible = "gpio-fan";
> +			gpios = <&pca9555_1 3 GPIO_ACTIVE_HIGH>;
> +			gpio-fan,speed-map = <0 0 3000 1>;

It would be nice to format this with a newline between the two map
entries.

> +		};
> +	};
> +
> +	reg_usb3_vbus: usb3-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb3-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&pca9555_1 15 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_usb2_0_vbus: v5-vbus0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-vbus0";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&pca9555_1 14 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_usb2_1_vbus: v5-vbus1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-vbus1";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&pca9555_0 4 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_usb2_1_vbus: v5-vbus1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-vbus1";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&pca9555_0 4 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_sata0: pwr-sata0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "pwr_en_sata0";
> +		enable-active-high;
> +		regulator-always-on;
> +
> +	};
> +
> +	reg_5v_sata0: v5-sata0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata0";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata0>;
> +	};
> +
> +	reg_12v_sata0: v12-sata0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata0";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata0>;
> +	};
> +
> +	reg_sata1: pwr-sata1 {
> +		regulator-name = "pwr_en_sata1";
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&pca9555_0 3 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_5v_sata1: v5-sata1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata1";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata1>;
> +	};
> +
> +	reg_12v_sata1: v12-sata1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata1";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata1>;
> +	};
> +
> +	reg_sata2: pwr-sata2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "pwr_en_sata2";
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&pca9555_0 11 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_5v_sata2: v5-sata2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata2";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata2>;
> +	};
> +
> +	reg_12v_sata2: v12-sata2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata2";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata2>;
> +	};
> +
> +	reg_sata3: pwr-sata3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "pwr_en_sata3";
> +		enable-active-high;
> +		regulator-always-on;
> +		gpio = <&pca9555_0 12 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_5v_sata3: v5-sata3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5.0-sata3";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata3>;
> +	};
> +
> +	reg_12v_sata3: v12-sata3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v12.0-sata3";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_sata3>;
> +	};
> +};

What is the quality of the power supply? What you often see if that
SATA drives are spun up sequentially, in order to not strain the power
supply with the current draw of them all starting at the same
time. There is a property, startup-delay-us, which can be used for
this.

	Andrew

> +
> +&pinctrl {
> +	pca0_pins: pca0_pins {
> +		marvell,pins = "mpp18";
> +		marvell,function = "gpio";
> +	};
> +};
> -- 
> 1.9.1
>