[PATCH 2/5] phy: qcom: Add Qualcomm PCIe PHY
Stanimir Varbanov
svarbanov at mm-sol.com
Fri Dec 12 09:13:58 PST 2014
Add a PCIe PHY driver used by PCIe host controller driver
on Qualcomm SoCs like Snapdragon 805.
Signed-off-by: Stanimir Varbanov <svarbanov at mm-sol.com>
---
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-pcie.c | 311 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 319 insertions(+), 0 deletions(-)
create mode 100644 drivers/phy/phy-qcom-pcie.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 2a436e6..135bdcc 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -218,6 +218,13 @@ config PHY_QCOM_IPQ806X_SATA
depends on OF
select GENERIC_PHY
+config PHY_QCOM_PCIE
+ tristate "Qualcomm PCIe SerDes/PHY driver"
+ depends on ARCH_QCOM
+ depends on HAS_IOMEM
+ depends on OF
+ select GENERIC_PHY
+
config PHY_ST_SPEAR1310_MIPHY
tristate "ST SPEAR1310-MIPHY driver"
select GENERIC_PHY
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c4590fc..e7662fb 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -26,6 +26,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2) += phy-s5pv210-usb2.o
obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_PCIE) += phy-qcom-pcie.o
obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
diff --git a/drivers/phy/phy-qcom-pcie.c b/drivers/phy/phy-qcom-pcie.c
new file mode 100644
index 0000000..3db348a
--- /dev/null
+++ b/drivers/phy/phy-qcom-pcie.c
@@ -0,0 +1,311 @@
+/*
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+#define QSERDES_COM_PLL_CP_SETI 0x024
+#define QSERDES_COM_PLL_IP_SETP 0x028
+#define QSERDES_COM_PLL_CP_SETP 0x02c
+#define QSERDES_COM_SYSCLK_EN_SEL 0x038
+#define QSERDES_COM_RESETSM_CNTRL 0x040
+#define QSERDES_COM_PLLLOCK_CMP1 0x044
+#define QSERDES_COM_PLLLOCK_CMP2 0x048
+#define QSERDES_COM_PLLLOCK_CMP_EN 0x050
+#define QSERDES_COM_DEC_START1 0x064
+#define QSERDES_COM_DIV_FRAC_START1 0x098
+#define QSERDES_COM_DIV_FRAC_START2 0x09c
+#define QSERDES_COM_DIV_FRAC_START3 0x0a0
+#define QSERDES_COM_DEC_START2 0x0a4
+#define QSERDES_COM_PLL_RXTXEPCLK_EN 0x0a8
+#define QSERDES_COM_PLL_CRCTRL 0x0ac
+
+#define QSERDES_RX_CDR_CONTROL 0x400
+#define QSERDES_RX_CDR_CONTROL2 0x410
+#define QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE 0x42c
+#define QSERDES_RX_RX_EQ_GAIN12 0x430
+
+#define PCIE_PHY_SW_RESET 0x600
+#define PCIE_PHY_POWER_DOWN_CONTROL 0x604
+#define PCIE_PHY_START 0x608
+#define PCIE_PHY_ENDPOINT_REFCLK_DRIVE 0x648
+#define PCIE_PHY_POWER_STATE_CONFIG1 0x650
+#define PCIE_PHY_POWER_STATE_CONFIG2 0x654
+#define PCIE_PHY_PWRUP_RESET_DLY_TIME_SYSCLK 0x678
+#define PCIE_PHY_PWRUP_RESET_DLY_TIME_AUXCLK 0x67c
+#define PCIE_PHY_PCS_STATUS 0x6c8
+
+#define PHY_DELAY_MIN_US 995
+#define PHY_DELAY_MAX_US 1005
+#define PHY_RETRIES_COUNT 10
+
+#define PIPE_CLK_DELAY_MIN_US 5000
+#define PIPE_CLK_DELAY_MAX_US 5100
+#define PIPE_CLK_RETRIES_COUNT 10
+
+struct qcom_pcie_phy {
+ void __iomem *base;
+ struct clk *clk;
+ struct reset_control *res_phy;
+ struct regulator *vdda_pll;
+ struct regulator *vdda;
+ struct device *dev;
+};
+
+struct phy_regs {
+ u32 reg_offset;
+ u32 val;
+};
+
+static const struct phy_regs pcie_phy_regs[] = {
+ { PCIE_PHY_POWER_DOWN_CONTROL, 0x03 },
+ { QSERDES_COM_SYSCLK_EN_SEL, 0x08 },
+ { QSERDES_COM_DEC_START1, 0x82 },
+ { QSERDES_COM_DEC_START2, 0x03 },
+ { QSERDES_COM_DIV_FRAC_START1, 0xd5 },
+ { QSERDES_COM_DIV_FRAC_START2, 0xaa },
+ { QSERDES_COM_DIV_FRAC_START3, 0x13 },
+ { QSERDES_COM_PLLLOCK_CMP_EN, 0x01 },
+ { QSERDES_COM_PLLLOCK_CMP1, 0x2b },
+ { QSERDES_COM_PLLLOCK_CMP2, 0x68 },
+ { QSERDES_COM_PLL_CRCTRL, 0xff },
+ { QSERDES_COM_PLL_CP_SETI, 0x3f },
+ { QSERDES_COM_PLL_IP_SETP, 0x07 },
+ { QSERDES_COM_PLL_CP_SETP, 0x03 },
+ { QSERDES_RX_CDR_CONTROL, 0xf3 },
+ { QSERDES_RX_CDR_CONTROL2, 0x6b },
+ { QSERDES_COM_RESETSM_CNTRL, 0x10 },
+ { QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE, 0x87 },
+ { QSERDES_RX_RX_EQ_GAIN12, 0x54 },
+ { PCIE_PHY_POWER_STATE_CONFIG1, 0xa3 },
+ { PCIE_PHY_POWER_STATE_CONFIG2, 0xcb },
+ { QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10 },
+ { PCIE_PHY_ENDPOINT_REFCLK_DRIVE, 0x10 },
+ { PCIE_PHY_SW_RESET, 0x00 },
+ { PCIE_PHY_START, 0x03 },
+};
+
+static void qcom_pcie_phy_init(struct qcom_pcie_phy *pcie)
+{
+ const struct phy_regs *regs = pcie_phy_regs;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(pcie_phy_regs); i++)
+ writel(regs[i].val, pcie->base + regs[i].reg_offset);
+}
+
+static bool qcom_pcie_phy_is_ready(struct qcom_pcie_phy *pcie)
+{
+ u32 val = readl(pcie->base + PCIE_PHY_PCS_STATUS);
+
+ return val & BIT(6) ? false : true;
+}
+
+static int qcom_pcie_phy_power_on(struct phy *phy)
+{
+ struct qcom_pcie_phy *pcie = phy_get_drvdata(phy);
+ struct device *dev = pcie->dev;
+ int ret, retries;
+
+ ret = regulator_enable(pcie->vdda_pll);
+ if (ret) {
+ dev_err(dev, "cannot enable vdda_pll regulator\n");
+ return ret;
+ }
+
+ ret = regulator_enable(pcie->vdda);
+ if (ret) {
+ dev_err(dev, "cannot enable vdda regulator\n");
+ goto fail_vdda_pll;
+ }
+
+ ret = reset_control_deassert(pcie->res_phy);
+ if (ret) {
+ dev_err(dev, "cannot deassert phy reset\n");
+ goto fail_vdda;
+ }
+
+ qcom_pcie_phy_init(pcie);
+
+ usleep_range(PHY_DELAY_MIN_US, PHY_DELAY_MAX_US);
+
+ ret = clk_set_rate(pcie->clk, ~0);
+ if (ret) {
+ dev_err(dev, "cannot set pipe clk rate\n");
+ goto fail_res;
+ }
+
+ /*
+ * setting pipe rate takes time, try arbitrary delay before enabling
+ * the clock
+ */
+ retries = PIPE_CLK_RETRIES_COUNT;
+ do {
+ usleep_range(PIPE_CLK_DELAY_MIN_US, PIPE_CLK_DELAY_MAX_US);
+
+ ret = clk_prepare_enable(pcie->clk);
+ if (!ret)
+ break;
+ } while (retries--);
+
+ if (retries < 0) {
+ dev_err(dev, "cannot enable phy clock\n");
+ goto fail_res;
+ }
+
+ retries = PHY_RETRIES_COUNT;
+ do {
+ ret = qcom_pcie_phy_is_ready(pcie);
+ if (ret)
+ break;
+ usleep_range(PHY_DELAY_MIN_US, PHY_DELAY_MAX_US);
+ } while (retries--);
+
+ if (retries < 0) {
+ dev_err(dev, "phy failed to come up\n");
+ ret = -ETIMEDOUT;
+ goto fail;
+ }
+
+ return 0;
+
+fail:
+ clk_disable_unprepare(pcie->clk);
+fail_res:
+ reset_control_assert(pcie->res_phy);
+fail_vdda:
+ regulator_disable(pcie->vdda);
+fail_vdda_pll:
+ regulator_disable(pcie->vdda_pll);
+
+ return ret;
+}
+
+static int qcom_pcie_phy_power_off(struct phy *phy)
+{
+ struct qcom_pcie_phy *pcie = phy_get_drvdata(phy);
+
+ writel(1, pcie->base + PCIE_PHY_SW_RESET);
+ writel(0, pcie->base + PCIE_PHY_POWER_DOWN_CONTROL);
+
+ reset_control_assert(pcie->res_phy);
+ clk_disable_unprepare(pcie->clk);
+ regulator_disable(pcie->vdda);
+ regulator_disable(pcie->vdda_pll);
+
+ return 0;
+}
+
+static struct phy_ops qcom_pcie_phy_ops = {
+ .power_on = qcom_pcie_phy_power_on,
+ .power_off = qcom_pcie_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_pcie_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy_provider *provider;
+ struct qcom_pcie_phy *pcie;
+ struct resource *res;
+ struct phy *phy;
+
+ pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+ if (!pcie)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pcie->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(pcie->base))
+ return PTR_ERR(pcie->base);
+
+ pcie->clk = devm_clk_get(dev, "core");
+ if (IS_ERR(pcie->clk)) {
+ dev_err(dev, "failed to get pcie phy clock\n");
+ return PTR_ERR(pcie->clk);
+ }
+
+ pcie->vdda = devm_regulator_get(dev, "vdda");
+ if (IS_ERR(pcie->vdda)) {
+ dev_err(dev, "failed to get vdda regulator\n");
+ return PTR_ERR(pcie->vdda);
+ }
+
+ pcie->vdda_pll = devm_regulator_get(dev, "vdda_pll");
+ if (IS_ERR(pcie->vdda_pll)) {
+ dev_err(dev, "failed to get vdda_pll regulator\n");
+ return PTR_ERR(pcie->vdda_pll);
+ }
+
+ pcie->res_phy = devm_reset_control_get(dev, "phy");
+ if (IS_ERR(pcie->res_phy)) {
+ dev_err(dev, "cannot get phy reset controller");
+ return PTR_ERR(pcie->res_phy);
+ }
+
+ phy = devm_phy_create(dev, NULL, &qcom_pcie_phy_ops, NULL);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "failed to create phy\n");
+ return PTR_ERR(phy);
+ }
+
+ provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(provider)) {
+ dev_err(dev, "failed to register phy provider\n");
+ return PTR_ERR(provider);
+ }
+
+ pcie->dev = dev;
+ phy_set_drvdata(phy, pcie);
+ platform_set_drvdata(pdev, pcie);
+
+ return 0;
+}
+
+static int qcom_pcie_phy_remove(struct platform_device *pdev)
+{
+ struct qcom_pcie_phy *pcie = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(pcie->clk);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_pcie_phy_of_match[] = {
+ { .compatible = "qcom,pcie-phy" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_pcie_phy_of_match);
+
+static struct platform_driver qcom_pcie_phy_driver = {
+ .probe = qcom_pcie_phy_probe,
+ .remove = qcom_pcie_phy_remove,
+ .driver = {
+ .name = "pcie-phy",
+ .of_match_table = qcom_pcie_phy_of_match,
+ }
+};
+module_platform_driver(qcom_pcie_phy_driver);
+
+MODULE_AUTHOR("Stanimir Varbanov <svarbanov at mm-sol.com>");
+MODULE_DESCRIPTION("QCOM PCIe PHY driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:pcie-phy");
--
1.7.0.4
More information about the linux-arm-kernel
mailing list