[PATCH 2/4] arm: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi
Stefan Roese
sr at denx.de
Thu Aug 28 10:10:27 PDT 2014
The Technexion TAO3530 is a OMAP3530 based SOM. This patch adds the
basic support for it as an dtsi file which can be included by
baseboard equipped with this SOM. E.g. the Technexion Thunder
baseboard.
Signed-off-by: Stefan Roese <sr at denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein at head-acoustics.de>
Cc: Tapani Utriainen <tapani at technexion.com>
Cc: Tony Lindgren <tony at atomide.com>
---
arch/arm/boot/dts/omap3-tao3530.dtsi | 335 +++++++++++++++++++++++++++++++++++
1 file changed, 335 insertions(+)
create mode 100644 arch/arm/boot/dts/omap3-tao3530.dtsi
diff --git a/arch/arm/boot/dts/omap3-tao3530.dtsi b/arch/arm/boot/dts/omap3-tao3530.dtsi
new file mode 100644
index 0000000..3ec32cd
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-tao3530.dtsi
@@ -0,0 +1,335 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014 Stefan Roese <sr at denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap34xx-hs.dtsi"
+
+/ {
+ cpus {
+ cpu at 0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; /* gpio_162 */
+ vcc-supply = <&hsusb2_power>;
+ };
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "omap3beagle";
+
+ /* McBSP2 is used for onboard sound, same as on beagle */
+ ti,mcbsp = <&mcbsp2>;
+ ti,codec = <&twl_audio>;
+ };
+
+ /* Regulator to enable/switch the vcc of the Wifi module */
+ mmc2_sdio_poweron: regulator-mmc2-sdio-poweron {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-mmc2-sdio-poweron";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ gpio = <&gpio5 29 GPIO_ACTIVE_LOW>; /* gpio_157 */
+ enable-active-low;
+ startup-delay-us = <10000>;
+ };
+};
+
+&omap3_pmx_core {
+ hsusbb2_pins: pinmux_hsusbb2_pins {
+ pinctrl-single,pins = <
+ 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ 0x120 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
+ 0x122 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
+ 0x124 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
+ 0x126 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
+ >;
+ };
+
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ /* wlan GPIO output for WLAN_EN */
+ wlan_gpio: pinmux_wlan_gpio {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr gpio_157 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0x192 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
+ 0x194 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
+ >;
+ };
+
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ 0x198 (PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk gpio171 */
+ 0x19e (PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 gpio174 */
+ 0x19a (PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo gpio172 */
+ 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi gpio173 */
+ >;
+ };
+
+ mcspi3_pins: pinmux_mcspi3_pins {
+ pinctrl-single,pins = <
+ 0x5ac (PIN_OUTPUT | MUX_MODE1) /* etk_d0.mcspi3_simo gpio14 INPUT | MODE1 */
+ 0x5ae (PIN_INPUT_PULLUP | MUX_MODE1) /* etk_d1.mcspi3_somi gpio15 INPUT | MODE1 */
+ 0x5b0 (PIN_OUTPUT | MUX_MODE1) /* etk_d2.mcspi3_cs0 gpio16 INPUT | MODE1 */
+ 0x5b2 (PIN_INPUT | MUX_MODE1) /* etk_d3.mcspi3_clk gpio17 INPUT | MODE1 */
+ >;
+ };
+
+ mcbsp3_pins: pinmux_mcbsp3_pins {
+ pinctrl-single,pins = <
+ 0x13c (PIN_OUTPUT | MUX_MODE0) /* mcbsp3_dx */
+ 0x13e (PIN_INPUT | MUX_MODE0) /* mcbsp3_dr */
+ 0x140 (PIN_INPUT | MUX_MODE0) /* mcbsp3_clkx */
+ 0x142 (PIN_INPUT | MUX_MODE0) /* mcbsp3_fsx */
+ >;
+ };
+};
+
+/* McBSP1: mux'ed with GPIO158 as clock for HA-DSP */
+&mcbsp1 {
+ status = "disabled";
+};
+
+&mcbsp2 {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl at 48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+};
+
+&mcspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+
+ spidev at 0 {
+ compatible = "spidev";
+ spi-max-frequency = <48000000>;
+ reg = <0>;
+ spi-cpha;
+ };
+};
+
+&mcspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi3_pins>;
+
+ spidev at 0 {
+ compatible = "spidev";
+ spi-max-frequency = <48000000>;
+ reg = <0>;
+ spi-cpha;
+ };
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ cd-gpios = <&twl_gpio 0 0>;
+ bus-width = <8>;
+};
+
+// WiFi (Marvell 88W8686) on MMC2/SDIO
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&mmc2_sdio_poweron>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
+&twl_gpio {
+ ti,use-leds;
+ /* pullups: BIT(1) */
+ ti,pullups = <0x000002>;
+ /*
+ * pulldowns:
+ * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
+ * BIT(15), BIT(16), BIT(17)
+ */
+ ti,pulldowns = <0x03a1c4>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&mcbsp3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp3_pins>;
+};
+
+&gpmc {
+ nand at 0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <16>;
+
+ ti,nand-ecc-opt = "sw";
+ gpmc,device-nand;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <36>;
+ gpmc,cs-wr-off-ns = <36>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <24>;
+ gpmc,adv-wr-off-ns = <36>;
+ gpmc,oe-on-ns = <6>;
+ gpmc,oe-off-ns = <48>;
+ gpmc,we-on-ns = <6>;
+ gpmc,we-off-ns = <30>;
+ gpmc,rd-cycle-ns = <72>;
+ gpmc,wr-cycle-ns = <72>;
+ gpmc,access-ns = <54>;
+ gpmc,wr-access-ns = <30>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ x-loader at 0 {
+ label = "X-Loader";
+ reg = <0 0x80000>;
+ };
+
+ bootloaders at 80000 {
+ label = "U-Boot";
+ reg = <0x80000 0x1e0000>;
+ };
+
+ bootloaders_env at 260000 {
+ label = "U-Boot Env";
+ reg = <0x260000 0x20000>;
+ };
+
+ kernel at 280000 {
+ label = "Kernel";
+ reg = <0x280000 0x400000>;
+ };
+
+ filesystem at 680000 {
+ label = "File System";
+ reg = <0x680000 0xf980000>;
+ };
+ };
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
+
+&vaux2 {
+ regulator-name = "vdd_ehci";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
--
2.1.0
More information about the linux-arm-kernel
mailing list