[PATCH 2/5] arm64, thunder: Add initial dts for Cavium Thunder SoC

[Mark Rutland]

On Thu, Aug 28, 2014 at 05:15:56PM +0100, Robert Richter wrote:
> Olof,
> 
> On 30.07.14 11:14:23, Olof Johansson wrote:
> > On Wed, Jul 30, 2014 at 8:06 AM, Robert Richter <rric at kernel.org> wrote:
> > > From: Radha Mohan Chintakuntla <rchintakuntla at cavium.com>
> > >
> > > Add initial device tree nodes for Cavium Thunder SoCs with support of
> > > 48 cores and gicv3. The dts file requires further changes, esp. for
> > > pci, gicv3-its and smmu. This changes will be added later together
> > > with the device drivers.
> > >
> > > Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla at cavium.com>
> > > Signed-off-by: Robert Richter <rrichter at cavium.com>
> > > ---
> > >  arch/arm64/boot/dts/Makefile         |   1 +
> > >  arch/arm64/boot/dts/thunder-88xx.dts | 387 +++++++++++++++++++++++++++++++++++
> > >  2 files changed, 388 insertions(+)
> > >  create mode 100644 arch/arm64/boot/dts/thunder-88xx.dts
> > >
> > > diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
> > > index c52bdb051f66..f8001a62029c 100644
> > > --- a/arch/arm64/boot/dts/Makefile
> > > +++ b/arch/arm64/boot/dts/Makefile
> > > @@ -1,3 +1,4 @@
> > > +dtb-$(CONFIG_ARCH_THUNDER) += thunder-88xx.dtb
> > >  dtb-$(CONFIG_ARCH_VEXPRESS) += rtsm_ve-aemv8a.dtb foundation-v8.dtb
> > >  dtb-$(CONFIG_ARCH_XGENE) += apm-mustang.dtb
> > 
> > Oh, and:
> > 
> > Let's fix the mistake we made on 32-bit here (that we can't undo
> > unless we move all dts files now, which is too much churn), and put
> > each SoC vendor in its own subdirectory.
> > 
> > So, please add a arch/arm64/boot/dts/cavium/ directory, add a Makefile
> > and the dts there.
> > 
> > We should move vexpress under arm/   and xgene under apm/ too.
> 
> I was looking into this. It turned out that this would introduce more
> pain than it solves. The problem with introducing vendor subdirs for
> .dts files is that this will require also subdirs for .dtb files to
> avoid name conflicts. This means that dtb files are no longer in a
> single directory. Current build scripts and makefiles rely on this.
> E.g.:
> 
>  scripts/Makefile.lib:$(obj)/%.dtb.S: $(obj)/%.dtb
> 
> Thus, the introduction of vendor subdirs is not easy to implement and
> may break existing workflows. Also, no other arch has vendor subdirs.
> 
> A solution would be to have a naming scheme for dts files which
> requires the vendor in the file name, such as cavium-thunder-88xx.dtb.
> Though, these long names may look a bit ugly.
> 
> Hmm... Any thoughts?

That would make it possible to search, but the number of files in one
place might become somewhat overwelming (which I believe was Olof's
concern).

Olof, thoughts?

Mark.