[PATCH V2 1/2] ARM: dts: Add DT changes for display on snow

[Mark Rutland]

On Wed, Aug 27, 2014 at 03:48:27PM +0100, Ajay Kumar wrote:
> Add DT nodes for ptn3460 bridge chip and panel.
> Add backlight enable pin and backlight power supply for pwm-backlight.
> Also add bridge phandle needed by dp to enable display on snow.
> 
> Note that, snow doesn't support "chunghwa,claa101wb01" panel,
> but still we choose to reuse the binding since "chunghwa,claa101wb01"
> has similar LCD timings.

What does it actually have?

It's fine to have "chunghwa,claa101wb01" as a fallback but we should
have an identifier for the actual display, too.

Thanks,
Mark.

> Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
> ---
> Changes since V1:
> 	-- Remove "simple-panel" compatible string.
> 	-- Use GPIO_ACTIVE_HIGH instead of 0.
> 	-- Change panel node naming from "panel-simple" to "panel".
> 
>  arch/arm/boot/dts/exynos5250-snow.dts |   41 ++++++++++++++++++---------------
>  1 file changed, 22 insertions(+), 19 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
> index f2b8c41..1ac9709 100644
> --- a/arch/arm/boot/dts/exynos5250-snow.dts
> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
> @@ -9,6 +9,7 @@
>  */
>  
>  /dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
>  #include "exynos5250.dtsi"
>  #include "exynos5250-cros-common.dtsi"
>  
> @@ -181,7 +182,7 @@
>  					dcdc3 {
>  						ti,enable-ext-control;
>  					};
> -					fet1 {
> +					fet1: fet1 {
>  						regulator-name = "vcd_led";
>  						ti,overcurrent-wait = <3>;
>  					};
> @@ -204,7 +205,7 @@
>  						regulator-always-on;
>  						ti,overcurrent-wait = <3>;
>  					};
> -					fet6 {
> +					fet6: fet6 {
>  						regulator-name = "lcd_vdd";
>  						ti,overcurrent-wait = <3>;
>  					};
> @@ -253,6 +254,15 @@
>  			pinctrl-0 = <&max98095_en>;
>  			pinctrl-names = "default";
>  		};
> +
> +		ptn3460: lvds-bridge at 20 {
> +			compatible = "nxp,ptn3460";
> +			reg = <0x20>;
> +			powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
> +			reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
> +			edid-emulation = <5>;
> +			panel = <&panel>;
> +		};
>  	};
>  
>  	i2s0: i2s at 03830000 {
> @@ -300,11 +310,13 @@
>  		vdd_pll-supply = <&ldo8_reg>;
>  	};
>  
> -	backlight {
> +	backlight: backlight {
>  		compatible = "pwm-backlight";
>  		pwms = <&pwm 0 1000000 0>;
>  		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
>  		default-brightness-level = <7>;
> +		enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
> +		power-supply = <&fet1>;
>  		pinctrl-0 = <&pwm0_out>;
>  		pinctrl-names = "default";
>  	};
> @@ -314,6 +326,12 @@
>  		samsung,invert-vclk;
>  	};
>  
> +	panel: panel {
> +		compatible = "chunghwa,claa101wb01";
> +		power-supply = <&fet6>;
> +		backlight = <&backlight>;
> +	};
> +
>  	dp-controller at 145B0000 {
>  		status = "okay";
>  		pinctrl-names = "default";
> @@ -325,22 +343,7 @@
>  		samsung,link-rate = <0x0a>;
>  		samsung,lane-count = <2>;
>  		samsung,hpd-gpio = <&gpx0 7 0>;
> -
> -		display-timings {
> -			native-mode = <&timing1>;
> -
> -			timing1: timing at 1 {
> -				clock-frequency = <70589280>;
> -				hactive = <1366>;
> -				vactive = <768>;
> -				hfront-porch = <40>;
> -				hback-porch = <40>;
> -				hsync-len = <32>;
> -				vback-porch = <10>;
> -				vfront-porch = <12>;
> -				vsync-len = <6>;
> -			};
> -		};
> +		bridge = <&ptn3460>;
>  	};
>  };
>  
> -- 
> 1.7.9.5
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>