[PATCH V2 3/3] mmc: dw_mmc: Dont cut off vqmmc and vmmc
Jaehoon Chung
jh80.chung at samsung.com
Tue Aug 26 21:47:02 PDT 2014
Doug,
On 08/27/2014 01:14 PM, Doug Anderson wrote:
> Jaehoon,
>
> On Tue, Aug 26, 2014 at 8:48 PM, Jaehoon Chung <jh80.chung at samsung.com> wrote:
>> Hi, Doug,
>>
>> On 08/26/2014 12:25 AM, Doug Anderson wrote:
>>> Jaehoon,
>>>
>>> On Mon, Aug 25, 2014 at 1:50 AM, Jaehoon Chung <jh80.chung at samsung.com> wrote:
>>>> On 08/25/2014 05:13 PM, Ulf Hansson wrote:
>>>>> On 22 August 2014 20:27, Sonny Rao <sonnyrao at chromium.org> wrote:
>>>>>> On Fri, Aug 22, 2014 at 8:31 AM, Ulf Hansson <ulf.hansson at linaro.org> wrote:
>>>>>>> On 22 August 2014 15:47, Yuvaraj Kumar C D <yuvaraj.cd at gmail.com> wrote:
>>>>>>>> Exynos 5250 and 5420 based boards uses built-in CD# line for card
>>>>>>>> detection.But unfortunately CD# line is on the same voltage rails
>>>>>>>> as of I/O voltage rails. When we cut off vqmmc,the consequent card
>>>>>>>> detection will break in these boards.
>>>>
>>>> I didn't know that use CD# line for card detect.
>>>> And if CD# voltage rails and I/O voltage rail are same voltage, it doesn't make sense.
>>>> Which card is used with same voltages? (eMMC? SD? SDIO?)
>>>>
>>>> Well, I have checked Exynos5250 and 5420, but it looks like not same rails.
>>>
>>> I'm not sure I totally understood what you said. In my manual I have
>>> a table titled "Table 2-1 Exynos 5420 Pin List". Look in this table
>>> for XMMC2CDN and XMMC2DATA_0. Look to the right of the table and
>>> you'll see the power domain. For both it shows VDDQ_MMC2. If that
>>> doesn't mean that the two are in the same voltage domain then I don't
>>> know what does. Can you point to any examples where they have
>>> different voltage domains?
>> I think you're mis-understanding for it.
>> Right, It's described at exynos5420, but it's not connected.
>
> "It's not connected". What do you mean? If I were to guess I'd say
> that on some particular board you're looking at they don't happen to
> use the "CD" pin for card detect. If this is what you mean, it
> doesn't help me. exynos5420-peach-pit does use the CD pin for card
> detect. You can look at the DTS file and confirm it.
I didn't know how exynos5420-peach-pit's circuit is configured.
But i guess that almost all exynos5 boards are configured with the similar circuit.
At Almost all Exynos5 board, CD-pin is used, but not included in Same power domain.
(CD-pin is external card-detect pin. - like XEINT_# pin)
You mentioned CD# and DATA# lines is used the same power domain, right?
In Circuit (not exynos5420-peach-pit), DATA# line and CMD/CLK(vqmmc) is same power supply, and vdd is used other power supply.
Not use the CD# pin, used the XEINT_# pin.
So i think we don't need to consider the CD#.
If exynos5420-peach-pit board is used the CD#-pin, then our discussion can be changed.
Your commit message looks like all exynos5250/5420 board are used CD# line.
>
> ...or are you saying that the CD pin somehow changes voltage domains
> when configured as a GPIO? I find that very hard to believe. What
> voltage domain does it go to? If it goes to a 1.8V voltage domain
> then that would be bad when vqmmc was 3.3V. If it goes to a 3.3V
> voltage domain then that would be bad when vqmmc was 1.8V. Remember
> that externally we've got a pull up to vqmmc.
It is used with XEINT_# pin instead of CD# pin.
As i mentioned above, if exynos5420-peach-pit is used CD# line and not used XEINT_# pin,
my point is meaningless. :)
Is exynos5420-peach-pit board used with CD#pin, not XEINT_# pin?
Best Regards,
Jaehoon Chung
>
> Even if somehow magically we can read the card detect pin with vqmmc
> off, we have an external pullup on this line that goes directly to the
> "vqmmc" power rail. If the vqmmc power rail is off then this external
> pull up would not work and would actually act as an external pull down
> if you could somehow configure the internal line to be a pullup.
>
>
>> Exynos4 series are also described, but we used the broken card detection scheme and power used one of "always-on" powers.
>> Because Card-detection rail need to enable as "always-on".
>>
>> We don't need to consider this. I checked the circuit, this patch didn't need.
>>
>> exynos5 also used the gpio-pin for card-detection. And we can use the slot-gpio API.
>
> When you say "exynos5", what do you mean here? Do you mean the smdk
> for 5250, or something else?
>
More information about the linux-arm-kernel
mailing list