[PATCH 1/3] ARM: dts: Add DT changes for display on snow

[Andreas Färber]

Am 25.07.2014 21:44, schrieb Ajay Kumar:
> Add DT nodes for ptn3460 bridge chip and panel-simple panel.

"simple-panel"

> Add backlight enable pin and backlight power supply for pwm-backlight.
> Also add bridge phandle needed by dp to enable display on snow.
> 
> Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
> ---
>  arch/arm/boot/dts/exynos5250-snow.dts |   40 +++++++++++++++++----------------
>  1 file changed, 21 insertions(+), 19 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
> index 6c36d41..f57f993 100644
> --- a/arch/arm/boot/dts/exynos5250-snow.dts
> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
> @@ -270,7 +270,7 @@
>  					dcdc3 {
>  						ti,enable-ext-control;
>  					};
> -					fet1 {
> +					fet1: fet1 {
>  						regulator-name = "vcd_led";
>  						ti,overcurrent-wait = <3>;
>  					};
> @@ -293,7 +293,7 @@
>  						regulator-always-on;
>  						ti,overcurrent-wait = <3>;
>  					};
> -					fet6 {
> +					fet6: fet6 {
>  						regulator-name = "lcd_vdd";
>  						ti,overcurrent-wait = <3>;
>  					};
> @@ -342,6 +342,15 @@
>  			pinctrl-0 = <&max98095_en>;
>  			pinctrl-names = "default";
>  		};
> +
> +		ptn3460: ptn3460-bridge at 20 {

"lvds-bridge"? (AF)

> +			compatible = "nxp,ptn3460";
> +			reg = <0x20>;
> +			powerdown-gpios = <&gpy2 5 0>;
> +			reset-gpios = <&gpx1 5 0>;
> +			edid-emulation = <5>;
> +			panel = <&panel>;
> +		};
>  	};
>  
>  	i2s0: i2s at 03830000 {
> @@ -389,11 +398,13 @@
>  		vdd_pll-supply = <&ldo8_reg>;
>  	};
>  
> -	backlight {
> +	backlight: backlight {
>  		compatible = "pwm-backlight";
>  		pwms = <&pwm 0 1000000 0>;
>  		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
>  		default-brightness-level = <7>;
> +		enable-gpios = <&gpx3 0 0>;
> +		power-supply = <&fet1>;
>  		pinctrl-0 = <&pwm0_out>;
>  		pinctrl-names = "default";
>  	};
> @@ -403,6 +414,12 @@
>  		samsung,invert-vclk;
>  	};
>  
> +	panel: panel-simple {

Just "panel"? (AF)

> +		compatible = "simple-panel";

Use something more concrete than "simple-panel"? (Thierry)

> +		power-supply = <&fet6>;
> +		backlight = <&backlight>;
> +	};
> +
>  	dp-controller at 145B0000 {
>  		status = "okay";
>  		pinctrl-names = "default";
> @@ -414,21 +431,6 @@
>  		samsung,link-rate = <0x0a>;
>  		samsung,lane-count = <2>;
>  		samsung,hpd-gpio = <&gpx0 7 0>;
> -
> -		display-timings {
> -			native-mode = <&timing1>;
> -
> -			timing1: timing at 1 {
> -				clock-frequency = <70589280>;
> -				hactive = <1366>;
> -				vactive = <768>;
> -				hfront-porch = <40>;
> -				hback-porch = <40>;
> -				hsync-len = <32>;
> -				vback-porch = <10>;
> -				vfront-porch = <12>;
> -				vsync-len = <6>;
> -			};
> -		};
> +		bridge = <&ptn3460>;
>  	};
>  };

This patch will trivially conflict with my Snow cleanup [1]; ptn3460
would go into the appropriate &i2c_* and this hunk into &dp then.

Regards,
Andreas

[1] https://patchwork.kernel.org/patch/4664801/

-- 
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg