[RFC PATCH 3/4] tty: omap-serial: use threaded interrupt handler

[Frans Klaver]

On Wed, Aug 20, 2014 at 11:06:05AM -0500, Felipe Balbi wrote:
> On Wed, Aug 20, 2014 at 08:40:28AM +0200, Frans Klaver wrote:
> > On Tue, Aug 19, 2014 at 01:57:02PM -0500, Felipe Balbi wrote:
> > > On Tue, Aug 19, 2014 at 02:14:47PM +0200, Frans Klaver wrote:
> > > > At 3.6Mbaud, with slightly over 2Mbit/s data coming in, we see 1600 uart
> > > > rx buffer overflows within 30 seconds. Threading the interrupt handling reduces
> > > > this to about 170 overflows in 10 minutes.
> > > 
> > > Can you try Sebastian Siewior's patches for 8250_omap and 8250 dma
> > > support ? That should help you a lot.
> > 
> > I'll have a look at that series. Thanks for pointing it out.

I have had a look at Sebastian's series, but I'm not convinced
yet that we should use it. So far the serial console seems to be
missing data every now and then. I haven't gotten around to testing our
high traffic application yet.


> > > >  drivers/tty/serial/omap-serial.c | 31 ++++++++++++++++++++++++-------
> > > >  1 file changed, 24 insertions(+), 7 deletions(-)
> > > > 
> > > > diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
> > > > index 14a0167..57664b9 100644
> > > > --- a/drivers/tty/serial/omap-serial.c
> > > > +++ b/drivers/tty/serial/omap-serial.c
> > > > @@ -575,6 +575,21 @@ static void serial_omap_rdi(struct uart_omap_port *up, unsigned int lsr)
> > > >  }
> > > >  
> > > >  /**
> > > > + * serial_omap_fast_irq() - schedule interrupt handling
> > > > + */
> > > > +static irqreturn_t serial_omap_fast_irq(int irq, void *dev_id)
> > > > +{
> > > > +	struct uart_omap_port *up = dev_id;
> > > > +	unsigned int iir = serial_in(up, UART_IIR);
> > > > +
> > > > +	if (iir & UART_IIR_NO_INT)
> > > > +		return IRQ_NONE;
> > > > +
> > > > +	disable_irq_nosync(up->port.irq);
> > > 
> > > NAK. Either use IRQF_ONESHOT or actually mask the IRQs at the device's
> > > registers (basically clearing IER).
> > 
> > Given the work that's been done on the 8250 based driver, what are the
> > short-term chances omap-serial will be dropped? I'd be happy to improve
> > here if it makes sense to do so. If the 8250 based driver is going to
> > replace omap-serial anyway on the short term, I don't see the point of
> > further developing this patch. The others would still make sense in my
> > opinion.
> 
> if we find a way to maintain the same ttyO* naming scheme and make it
> coexist with ttyS* naming, then we could drop as soon as 8250_omap is
> ready for prime time.

With that in mind, for now I'll be betting on two horses.

I'll cook up a new version using oneshot.

Thanks,
Frans