[PATCHv10 2/2] arm: dts: Add Altera SDRAM EDAC bindings & devicetree entries.

[Steffen Trumtrar]

Hi!

tthayer at opensource.altera.com writes:

> From: Thor Thayer <tthayer at opensource.altera.com>
>
> Add the Altera SDRAM EDAC bindings and device tree changes to the Altera SoC project.
>
> Signed-off-by: Thor Thayer <tthayer at opensource.altera.com>
> ---
> v2: Changes to SoC SDRAM EDAC code.
>
> v3: Implement code suggestions for SDRAM EDAC code.
>
> v4: Remove syscon from SDRAM controller bindings.
>
> v5: No Change, bump version for consistency.
>
> v6: Only map the ctrlcfg register as syscon.
>
> v7: No change. Bump for consistency.
>
> v8: No change. Bump for consistency.
>
> v9: Changes to support a MFD SDRAM controller with nested EDAC.
>
> v10: Revert to using syscon based on feedback.
> ---
>  .../bindings/arm/altera/socfpga-sdram-edac.txt     |   15 +++++++++++++++
>  arch/arm/boot/dts/socfpga.dtsi                     |   11 +++++++++++
>  2 files changed, 26 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt
>
> diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt
> new file mode 100644
> index 0000000..d0ce01d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-edac.txt
> @@ -0,0 +1,15 @@
> +Altera SOCFPGA SDRAM Error Detection & Correction [EDAC]
> +The EDAC accesses a range of registers in the SDRAM controller.
> +
> +Required properties:
> +- compatible : should contain "altr,sdram-edac";
> +- altr,sdr-syscon : phandle of the sdr module
> +- interrupts : Should contain the SDRAM ECC IRQ in the
> +	appropriate format for the IRQ controller.
> +
> +Example:
> +	sdramedac {
> +		compatible = "altr,sdram-edac";
> +		altr,sdr-syscon = <&sdr>;
> +		interrupts = <0 39 4>;
> +	};
> diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
> index 4676f25..45b361e 100644
> --- a/arch/arm/boot/dts/socfpga.dtsi
> +++ b/arch/arm/boot/dts/socfpga.dtsi
> @@ -603,6 +603,17 @@
>  			};
>  		};
>  
> +		sdr: sdr at ffc25000 {
> +			compatible = "syscon";
> +			reg = <0xffc25000 0x1000>;
> +		};
> +
> +		sdramedac {
> +			compatible = "altr,sdram-edac";
> +			altr,sdr-syscon = <&sdr>;
> +			interrupts = <0 39 4>;
> +		};
> +
>  		L2: l2-cache at fffef000 {
>  			compatible = "arm,pl310-cache";
>  			reg = <0xfffef000 0x1000>;

Sorry, but I personally still don't like this approach.

If we do it like this however, shouldn't the different regions of the
SDR (EDAC, FPGAPORTRST, ...) at least be child nodes of the syscon?
That seems to match the syscon binding and describes the actual hardware
better IMHO.
Oh, and "reg = <...>" for the sdram-edac, maybe ?
How would I know where the start address of the EDAC is, if I would use
this DT on another OS where I don't have the same driver?

Regards,
Steffen

-- 
Pengutronix e.K.                           | Steffen Trumtrar            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |