[PATCH 4/4] ARM: dts: keystone-k2hk: add dsp gpio controllers nodes

[Grygorii Strashko]

Hi Alexander,

On 08/13/2014 07:06 PM, Alexander Shiyan wrote:
> Wed, 13 Aug 2014 19:16:22 +0300 от Grygorii Strashko <grygorii.strashko at ti.com>:
>> Add Keystone 2 DSP GPIO nodes.
>> DSP GPIO banks 0-7 correspond to DSP0-DSP7
>>
>> Signed-off-by: Grygorii Strashko <grygorii.strashko at ti.com>
>> ---
>>   arch/arm/boot/dts/k2hk.dtsi |   56 +++++++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 56 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/k2hk.dtsi b/arch/arm/boot/dts/k2hk.dtsi
>> index 321ba2f..009e180 100644
>> --- a/arch/arm/boot/dts/k2hk.dtsi
>> +++ b/arch/arm/boot/dts/k2hk.dtsi
>> @@ -50,5 +50,61 @@
>>   			#interrupt-cells = <1>;
>>   			ti,syscon-dev = <&devctrl 0x2a0>;
>>   		};
>> +
>> +		dspgpio0: keystone_dsp_gpio at 02620240 {
>> +			compatible = "ti,keystone-mctrl-gpio";
>> +			gpio-controller;
>> +			#gpio-cells = <2>;
>> +			gpio,syscon-dev = <&devctrl 0x240>;
>> +		};
>> +
>> +		dspgpio1: keystone_dsp_gpio at 2620244 {
>> +			compatible = "ti,keystone-mctrl-gpio";
>> +			gpio-controller;
>> +			#gpio-cells = <2>;
>> +			gpio,syscon-dev = <&devctrl 0x244>;
>> +		};
> ...
>> +		dspgpio7: keystone_dsp_gpio at 262025C {
>> +			compatible = "ti,keystone-mctrl-gpio";
>> +			gpio-controller;
>> +			#gpio-cells = <2>;
>> +			gpio,syscon-dev = <&devctrl 0x25c>;
>> +		};
> 
> So, devctrl is a syscon device and this DTS introduce several
> identical GPIO descriptions?
> 
> On my opinion this should be placed in the gpio-syscon.c,
> where you can add support for ti,keystone-dsp0{..7}-gpio.
> Such change will avoid parts 2 and 3 of this patch.
> 
> static const struct syscon_gpio_data ti_keystone_dsp0_gpio = {
>    .compatible = "ti,keystone-syscon",
>    .dat_bit_offset = 0x240 * 8,
>    ...
>    .set = etc...
> };

So, if I understand you right, you propose to add 8 additional compatible
strings just to encode different register offsets. Is it?
1) add "ti,keystone-mctrl-gpio0"..."ti,keystone-mctrl-gpio7"

2) add 8 structures keystone_mctrl_gpio0..keystone_mctrl_gpio7 in gpio-syscon.c
   (which will have only different values of field - .dat_bit_offset = 0x2yy * 8,)

3) add 8 additional items in array syscon_gpio_ids
	{
		.compatible	= "ti,keystone-mctrl-gpio0",
		.data		= &keystone_mctrl_gpio0,
	}, ...

I can do it if you strictly insist, BUT I don't like it :(
- just imagine how your driver will look look like if 5 or 6 SoCs will re-use it ;)
- as I mentioned in cover letter and commit messages even each SoC revision can have
  different Syscon implementation with different registers offsets and with different
  number of Syscon register ranges (for example for Keystone 2 we already have two
  Syscon devices defined in DT).

Now we already have 3 Keystone 2 SoC revisions (K2HK, K2L, K2E)  and there are no guarantee
that the next revision k2X will have the same register offset for GPIO0.

Best regards,
-grygorii