[RESEND PATCH 2/2] ARM: dts: Add tps65090 FET constraints on Peach Pit and Pi
Javier Martinez Canillas
javier.martinez at collabora.co.uk
Mon Aug 11 10:47:18 PDT 2014
Hello Doug,
On 08/11/2014 05:57 PM, Doug Anderson wrote:
> Javier,
>
> On Mon, Aug 11, 2014 at 4:38 AM, Javier Martinez Canillas
> <javier.martinez at collabora.co.uk> wrote:
>> Both Exynos5420 Peach Pit and Exynos5800 Peach Pi boards
>> have a tps65090 PMU that has a number of switches (FETs)
>> that are just on/off devices but they do have a current
>> limit and the output voltage of the switch is ramped up
>> within a controlled slope.
>>
>> After the switch is turned on, a safety timer is started
>> and before this timer times out the output voltage must
>> have reached the input voltage. Otherwise the switch is
>> turned off expecting an overload condition.
>>
>> So using the maximum output voltage slew rate and the timer
>> minimum and maximum timeouts, a voltage constraints can be
>> expressed as bounded limits for the timeout. That is what
>> is used in the board schematics and should be in the DT too.
>
> I don't understand this, but if you and Mark are happy with it...
>
> ...I'm also not 100% certain what the above description has to do with
> this change, but I'll admit to having only skimmed some of the earlier
> conversations.
>
As I stated before, I wrongly assumed from where the constraints in the
schematics came from. From the latest doc I now know that there is a
"recommended operating conditions table". I'll fix it in v2, sorry for the
confusion...
>
>> Signed-off-by: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
>> ---
>> arch/arm/boot/dts/exynos5420-peach-pit.dts | 14 ++++++++++++++
>> arch/arm/boot/dts/exynos5800-peach-pi.dts | 14 ++++++++++++++
>> 2 files changed, 28 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> index d8710c1..eefafe6 100644
>> --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> @@ -386,27 +386,41 @@
>> };
>> tps65090_fet1: fet1 {
>> regulator-name = "vcd_led";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <1700000>;
>
> This is almost certainly wrong. Your max is smaller than your min.
> Perhaps you want an extra 0.
>
>> };
>> tps65090_fet2: fet2 {
>> regulator-name = "video_mid";
>> + regulator-min-microvolt = <4500000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_fet3: fet3 {
>> regulator-name = "wwan_r";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_fet4: fet4 {
>> regulator-name = "sdcard";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_fet5: fet5 {
>> regulator-name = "camout";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> };
>> tps65090_fet6: fet6 {
>> regulator-name = "lcd_vdd";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> };
>> tps65090_fet7: fet7 {
>> regulator-name = "video_mid_1a";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_ldo1: ldo1 {
>> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> index 07b29b7..5c38bc0 100644
>> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> @@ -384,27 +384,41 @@
>> };
>> tps65090_fet1: fet1 {
>> regulator-name = "vcd_led";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <1700000>;
>
> Here, too.
>
>> };
>> tps65090_fet2: fet2 {
>> regulator-name = "video_mid";
>> + regulator-min-microvolt = <4500000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_fet3: fet3 {
>> regulator-name = "wwan_r";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_fet4: fet4 {
>> regulator-name = "sdcard";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_fet5: fet5 {
>> regulator-name = "camout";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> };
>> tps65090_fet6: fet6 {
>> regulator-name = "lcd_vdd";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> };
>> tps65090_fet7: fet7 {
>> regulator-name = "video_mid_1a";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <5500000>;
>> regulator-always-on;
>> };
>> tps65090_ldo1: ldo1 {
>
> Other than 1.7V vs. 17V, this matches what I see in the tps65090
> specifications. Technically I think that this should also be applied
> to other tps65090 users in mainline since it's a property shared among
> every user of tps65090. That means exynos5250-snow and
> tegra114-dalmore. I'd be tempted to say that it belongs in source
> code or in a dts fragment as well.
>
Agreed, now is clear from the table that these are operating conditions related
to the PMIC and is not a per board value. So since these are constants, they
should be added to the driver source code and not in the DTS. I'll do this in v2
as well.
> -Doug
>
Best regards,
Javier
More information about the linux-arm-kernel
mailing list