[PATCHv9 00/43] ARM: TI SoC clock DT conversion

[Nishanth Menon]

On 10/31/2013 04:10 AM, Tero Kristo wrote:
> On 10/30/2013 10:10 PM, Nishanth Menon wrote:
>> On 10/30/2013 10:00 AM, Nishanth Menon wrote:
>>> On 10/30/2013 03:23 AM, Tero Kristo wrote:
>>>> On 10/29/2013 06:19 PM, Nishanth Menon wrote:
>>>>> On 10/25/2013 10:56 AM, Tero Kristo wrote:
>>>>> <snip>
>>>>>> Testing done:
>>>>>> - omap3-beagle: boot + suspend/resume (ret + off)
>>>>>> - omap4-panda-es: boot + suspend/resume
>>>>>> - omap5-uevm: boot
>>>>>> - dra7-evm: boot
>>>>>> - am335x-bone: boot
>>>>>>
>>>>>> Test branches available:
>>>>>>
>>>>>> tree: https://github.com/t-kristo/linux-pm.git
>>>>>
>>>>> <snip>
>>>>>> Fully functioning test branch: 3.12-rc6-dt-clks-v9
>>>>>>
>>>>> ^^ I tested this branch (boot testing):
>>>>> Beagle-XM: http://pastebin.com/50A1qtFq (crashes + clkdm issues, dpll5
>>>>> failed to transition)
>>>>
>>>> I just sent you a private email with a patch to try out, should fix the
>>>> boot crash at least hopefully. Basically I forgot to convert one part of
>>>> the kernel to the new regmap stuff for omap36xx.
>>>
>>> it does bootup yes.
>>>>
>>>> clkdm issues are caused by wrong data in omap_hwmod_3xxx_data.c, USB
>>>> nodes are listing l3_init_clkdm for them, but this only exists on
>>>> omap4+. Seems like some copy paste bug introduced by someone.
>>>>
>>>> dpll5 part I am not too sure, can you check if the same happens with
>>>> non-dt boot?
>>>
>>> no-dt: http://pastebin.com/bYP9fTzH
>>> dt: http://pastebin.com/xHup4L9Y
>>>
>>> dpll5 warning seems to be only in dt-boot?
>>>
>>
>> Tracked this down: you were missing the following - looks like the
>> conversion script might be missing converting the flags clock data
>> over to dts?
>>
>> diff --git
>> a/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
>> b/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
>> index 7e37e3e..c9b77c8 100644
>> --- a/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
>> +++ b/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
>> @@ -30,6 +30,7 @@
>>                  compatible = "ti,omap3-dpll-clock";
>>                  clocks = <&sys_ck>, <&sys_ck>;
>>                  reg = <0x0d04>, <0x0d24>, <0x0d34>, <0x0d4c>;
>> +               ti,low-power-stop;
>>          };
>>
>>          dpll5_m2_ck: dpll5_m2_ck {
>>
>>
>>
> 
> Yea, seems I introduced the problem with the conversion script changes. 
> The valid fix for this is actually at the end of this mail (this fixes 
> both of the problems introduced, and also completes the fix you did), I 
> will add the fixes to the next rev. 

One debug feedback:
reg = <0x0d04>, <0x0d24>, <0x0d34>, <0x0d4c>;
clocks = <&sys_ck>, <&sys_ck>;

we used indexing for varied register and clocks. however the register
meaning per index changes based on type of DPLL. This was one painful
thing to track down when debugging. the only robust option to debug
was to use prints as part of register write/reads to ensure that right
sequence was being followed.

I understand based on review comments for dtb size, we have removed
the names, but we lost sane debug capability as well with that.

-- 
Regards,
Nishanth Menon