acked
Gregory CLEMENT
gregory.clement at free-electrons.com
Wed Oct 30 13:22:08 EDT 2013
Hi Jason,
On 30/10/2013 18:15, Jason Cooper wrote:
> Gregory,
>
> I like the idea, and if you perhaps do '[PATCH X/Y] Acked' it should
> make it through the filters. (they currently whitelist 'GIT PULL' and
> 'PATCH' subjects).
>
Well actually it was a mistake! I ended to use a plugin to automatically
writing some pattern instead of writing it myself each time, but I
mis-configured it!
I am not sure that everybody like the idea to hijack the subject of a thread,
but if there a agreement on it, now I know hot to do it! ;)
Gregory
> Sure would make things easier when going through the threads...
>
> thx,
>
> Jason.
>
> On Wed, Oct 30, 2013 at 06:00:00PM +0100, Gregory CLEMENT wrote:
>> On 30/10/2013 17:55, Thomas Petazzoni wrote:
>>> The OpenBlocks A7 board is designed and sold by PlatHome, and based on
>>> a Kirkwood 6283 Marvell SoC. It is quite similar to the OpenBlocks A6
>>> already supported in the kernel, with the following main differences:
>>>
>>> - The A6 uses a RTC on I2C, while the A7 uses the internal SoC RTC.
>>>
>>> - The A6 has one Ethernet port, while the A7 has two Ethernet ports
>>>
>>> - The A6 has only one USB port, while the A7 integrates a USB hub,
>>> which provides two front-side USB port, and an internal USB port as
>>> well.
>>>
>>> - The A6 has 512 MB of RAM, while the A7 has 1 GB of RAM.
>>>
>>> - Slightly different GPIOs for some functions.
>>>
>>> Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
>>
>>
>> Acked-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
>>
>>
>>> ---
>>> arch/arm/boot/dts/Makefile | 3 +-
>>> arch/arm/boot/dts/kirkwood-openblocks_a7.dts | 223 +++++++++++++++++++++++++++
>>> 2 files changed, 225 insertions(+), 1 deletion(-)
>>> create mode 100644 arch/arm/boot/dts/kirkwood-openblocks_a7.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index 802720e..64783bb 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -101,7 +101,8 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
>>> kirkwood-topkick.dtb \
>>> kirkwood-ts219-6281.dtb \
>>> kirkwood-ts219-6282.dtb \
>>> - kirkwood-openblocks_a6.dtb
>>> + kirkwood-openblocks_a6.dtb \
>>> + kirkwood-openblocks_a7.dtb
>>> dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb
>>> dtb-$(CONFIG_ARCH_MSM) += msm8660-surf.dtb \
>>> msm8960-cdp.dtb
>>> diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a7.dts b/arch/arm/boot/dts/kirkwood-openblocks_a7.dts
>>> new file mode 100644
>>> index 0000000..1864972
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/kirkwood-openblocks_a7.dts
>>> @@ -0,0 +1,223 @@
>>> +/*
>>> + * Device Tree file for OpenBlocks A7 board
>>> + *
>>> + * Copyright (C) 2013 Free Electrons
>>> + *
>>> + * Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
>>> + *
>>> + * This file is licensed under the terms of the GNU General Public
>>> + * License version 2. This program is licensed "as is" without any
>>> + * warranty of any kind, whether express or implied.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "kirkwood.dtsi"
>>> +#include "kirkwood-6282.dtsi"
>>> +
>>> +/ {
>>> + model = "Plat'Home OpenBlocksA7";
>>> + compatible = "plathome,openblocks-a7", "marvell,kirkwood-88f6283", "marvell,kirkwood";
>>> +
>>> + memory {
>>> + device_type = "memory";
>>> + reg = <0x00000000 0x40000000>; /* 1 GB */
>>> + };
>>> +
>>> + chosen {
>>> + bootargs = "console=ttyS0,115200n8 earlyprintk";
>>> + };
>>> +
>>> + ocp at f1000000 {
>>> + serial at 12000 {
>>> + status = "ok";
>>> + pinctrl-0 = <&pmx_uart0>;
>>> + pinctrl-names = "default";
>>> + };
>>> +
>>> + serial at 12100 {
>>> + status = "ok";
>>> + pinctrl-0 = <&pmx_uart1>;
>>> + pinctrl-names = "default";
>>> + };
>>> +
>>> + nand at 3000000 {
>>> + chip-delay = <25>;
>>> + status = "okay";
>>> + pinctrl-0 = <&pmx_nand>;
>>> + pinctrl-names = "default";
>>> +
>>> + partition at 0 {
>>> + label = "uboot";
>>> + reg = <0x0 0x1c0000>;
>>> + };
>>> +
>>> + partition at 90000 {
>>> + label = "env";
>>> + reg = <0x1c0000 0x2c0000>;
>>> + };
>>> +
>>> + partition at d4000 {
>>> + label = "test";
>>> + reg = <0x480000 0x160000>;
>>> + };
>>> +
>>> + partition at f4000 {
>>> + label = "conf";
>>> + reg = <0x5e0000 0x540000>;
>>> + };
>>> +
>>> + partition at 4f4000 {
>>> + label = "linux";
>>> + reg = <0xb20000 0x3d40000>;
>>> + };
>>> +
>>> + partition at 2214000 {
>>> + label = "user";
>>> + reg = <0x4860000 0xb7a0000>;
>>> + };
>>> + };
>>> +
>>> + sata at 80000 {
>>> + nr-ports = <1>;
>>> + status = "okay";
>>> + };
>>> +
>>> + i2c at 11100 {
>>> + status = "okay";
>>> + pinctrl-0 = <&pmx_twsi1>;
>>> + pinctrl-names = "default";
>>> +
>>> + s24c02: s24c02 at 50 {
>>> + compatible = "24c02";
>>> + reg = <0x50>;
>>> + };
>>> + };
>>> +
>>> + pinctrl: pinctrl at 10000 {
>>> + pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header>;
>>> + pinctrl-names = "default";
>>> +
>>> + pmx_uart0: pmx-uart0 {
>>> + marvell,pins = "mpp10", "mpp11", "mpp15",
>>> + "mpp16";
>>> + marvell,function = "uart0";
>>> + };
>>> +
>>> + pmx_uart1: pmx-uart1 {
>>> + marvell,pins = "mpp13", "mpp14", "mpp8",
>>> + "mpp9";
>>> + marvell,function = "uart1";
>>> + };
>>> +
>>> + pmx_sysrst: pmx-sysrst {
>>> + marvell,pins = "mpp6";
>>> + marvell,function = "sysrst";
>>> + };
>>> +
>>> + pmx_dip_switches: pmx-dip-switches {
>>> + marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47";
>>> + marvell,function = "gpio";
>>> + };
>>> +
>>> + /*
>>> + * Accessible on connector J202. The MPP
>>> + * listed below are pin 1-7, pin 8 is unused,
>>> + * pin 9 is external reset input and pin 10 is
>>> + * ground.
>>> + */
>>> + pmx_gpio_header: pmx-gpio-header {
>>> + marvell,pins = "mpp17", "mpp7", "mpp29", "mpp28",
>>> + "mpp35", "mpp34", "mpp40";
>>> + marvell,function = "gpio";
>>> + };
>>> +
>>> + pmx_gpio_init: pmx-init {
>>> + marvell,pins = "mpp38";
>>> + marvell,function = "gpio";
>>> + };
>>> +
>>> + pmx_usb_oc: pmx-usb-oc {
>>> + marvell,pins = "mpp39";
>>> + marvell,function = "gpio";
>>> + };
>>> +
>>> + pmx_leds: pmx-leds {
>>> + marvell,pins = "mpp41", "mpp42", "mpp43";
>>> + marvell,function = "gpio";
>>> + };
>>> +
>>> + pmx_ge1: pmx-ge1 {
>>> + marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23",
>>> + "mpp24", "mpp25", "mpp26", "mpp27",
>>> + "mpp30", "mpp31", "mpp32", "mpp33";
>>> + marvell,function = "ge1";
>>> + };
>>> + };
>>> + };
>>> +
>>> + gpio-leds {
>>> + compatible = "gpio-leds";
>>> + pinctrl-0 = <&pmx_leds>;
>>> + pinctrl-names = "default";
>>> +
>>> + led-red {
>>> + label = "obsa7:red:stat";
>>> + gpios = <&gpio1 9 1>;
>>> + };
>>> +
>>> + led-green {
>>> + label = "obsa7:green:stat";
>>> + gpios = <&gpio1 10 1>;
>>> + };
>>> +
>>> + led-yellow {
>>> + label = "obsa7:yellow:stat";
>>> + gpios = <&gpio1 11 1>;
>>> + };
>>> + };
>>> +
>>> + gpio_keys {
>>> + compatible = "gpio-keys";
>>> + pinctrl-0 = <&pmx_gpio_init>;
>>> + pinctrl-names = "default";
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + button at 1 {
>>> + label = "Init Button";
>>> + linux,code = <116>;
>>> + gpios = <&gpio1 6 0>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&mdio {
>>> + status = "okay";
>>> +
>>> + ethphy0: ethernet-phy at 0 {
>>> + device_type = "ethernet-phy";
>>> + reg = <0>;
>>> + };
>>> +
>>> + ethphy1: ethernet-phy at 1 {
>>> + device_type = "ethernet-phy";
>>> + reg = <1>;
>>> + };
>>> +};
>>> +
>>> +ð0 {
>>> + status = "okay";
>>> + ethernet0-port at 0 {
>>> + phy-handle = <ðphy0>;
>>> + };
>>> +};
>>> +
>>> +ð1 {
>>> + status = "okay";
>>> + pinctrl-0 = <&pmx_ge1>;
>>> + pinctrl-names = "default";
>>> + ethernet1-port at 0 {
>>> + phy-handle = <ðphy1>;
>>> + };
>>> +};
>>>
>>
>>
>> --
>> Gregory Clement, Free Electrons
>> Kernel, drivers, real-time and embedded Linux
>> development, consulting, training and support.
>> http://free-electrons.com
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
More information about the linux-arm-kernel
mailing list