[PATCHv2 3/7] ARM: imx: add support code for IMX50 based machines

[gerg at uclinux.org]

From: Greg Ungerer <gerg at uclinux.org>

Add machine support code for the Freescale IMX50 SoC.

It is very similar to the Freescale IMX53, it contains many of the same
periperhal hardware modules, at the same address offsets as the IMX53.
(Notable exceptions are that the IMX50 contains no CAN bus hardware, less
GPIO, no VPU, it does contain an Electrophoretic display controller though).

So this support code just uses the IMX53 definitions as they are today.
We can add the extra IMX50 definitions in the future when required.

Signed-off-by: Greg Ungerer <gerg at uclinux.org>
---
 arch/arm/mach-imx/Makefile     |  1 +
 arch/arm/mach-imx/mach-imx50.c | 46 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 47 insertions(+)
 create mode 100644 arch/arm/mach-imx/mach-imx50.c

diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index bbe1f5b..924e117 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -112,6 +112,7 @@ obj-$(CONFIG_MACH_EUKREA_CPUIMX51SD) += mach-cpuimx51sd.o
 obj-$(CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD) += eukrea_mbimxsd51-baseboard.o
 
 obj-$(CONFIG_MACH_IMX51_DT) += imx51-dt.o
+obj-$(CONFIG_SOC_IMX50) += mach-imx50.o
 obj-$(CONFIG_SOC_IMX53) += mach-imx53.o
 
 obj-$(CONFIG_SOC_VF610) += clk-vf610.o mach-vf610.o
diff --git a/arch/arm/mach-imx/mach-imx50.c b/arch/arm/mach-imx/mach-imx50.c
new file mode 100644
index 0000000..2e1fe94
--- /dev/null
+++ b/arch/arm/mach-imx/mach-imx50.c
@@ -0,0 +1,46 @@
+/*
+ * Copyright 2013 Greg Ungerer <gerg at uclinux.org>
+ * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include "common.h"
+#include "mx53.h"
+
+static void __init imx50_dt_init(void)
+{
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
+static const char *imx50_dt_board_compat[] __initdata = {
+	"fsl,imx50",
+	NULL
+};
+
+DT_MACHINE_START(IMX50_DT, "Freescale i.MX50 (Device Tree Support)")
+	.map_io		= mx53_map_io,
+	.init_early	= imx53_init_early,
+	.init_irq	= mx53_init_irq,
+	.handle_irq	= imx53_handle_irq,
+	.init_machine	= imx50_dt_init,
+	.init_late	= imx53_init_late,
+	.dt_compat	= imx50_dt_board_compat,
+	.restart	= mxc_restart,
+MACHINE_END
-- 
1.8.1.4