[PATCHv7][ 1/4] Input: tsc2007: Add device tree support.

[Lothar Waßmann]

Hi,

Thierry Reding wrote:
> On Thu, Oct 24, 2013 at 02:42:13PM +0200, Denis Carikli wrote:
> > Cc: Rob Herring <rob.herring at calxeda.com>
> > Cc: Pawel Moll <pawel.moll at arm.com>
> > Cc: Mark Rutland <mark.rutland at arm.com>
> > Cc: Stephen Warren <swarren at wwwdotorg.org>
> > Cc: Ian Campbell <ijc+devicetree at hellion.org.uk>
> > Cc: devicetree at vger.kernel.org
> > Cc: Dmitry Torokhov <dmitry.torokhov at gmail.com>
> > Cc: linux-input at vger.kernel.org
> > Cc: Sascha Hauer <kernel at pengutronix.de>
> > Cc: linux-arm-kernel at lists.infradead.org
> > Cc: Lothar Waßmann <LW at KARO-electronics.de>
> > Cc: Eric Bénard <eric at eukrea.com>
> > Signed-off-by: Denis Carikli <denis at eukrea.com>
> > ---
> > ChangeLog v6->v7:
> > - One small whitespace cleanup.
> > - The properties specific to that driver are now prefixed with "ti,".
> > - The ti,fuzzy property has now better documentation.
> > ---
> >  .../bindings/input/touchscreen/tsc2007.txt         |   45 +++++
> >  drivers/input/touchscreen/tsc2007.c                |  194 +++++++++++++++-----
> >  2 files changed, 198 insertions(+), 41 deletions(-)
> >  create mode 100644 Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
> > new file mode 100644
> > index 0000000..516b63b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
> > @@ -0,0 +1,45 @@
> > +* Texas Instruments tsc2007 touchscreen controller
> > +
> > +Required properties:
> > +- compatible: must be "ti,tsc2007".
> > +- reg: I2C address of the chip.
> > +- ti,x-plate-ohms: X-plate resistance in ohms.
> > +
> > +Optional properties:
> > +- gpios: the interrupt gpio the chip is connected to (trough the penirq pin)
> > +  (see GPIO binding[2] for more details).
> > +- interrupt-parent: the phandle for the gpio controller
> > +  (see interrupt binding[1]).
> > +- interrupts: (gpio) interrupt to which the chip is connected
> > +  (see interrupt binding[1]).
> > +- pinctrl-0: Should specify pin control groups used for the gpio
> > +  (see pinctrl bindings[0]).
> > +- pinctrl-names: Should contain only one value - "default"
> > +  (see pinctrl bindings[0]).
> 
> Also I haven't seen a response as to why this can't be handled by the
> GPIO driver. Adding Linus Walleij, perhaps he knows a more definitive
> answer.
> 
> Linus, the issue here is that the pinctrl properties for this chip are
> supposed to pinmux the pendown GPIO for this chip. I was under the
> impression that this should be handled by the GPIO controller itself, so
> that when gpio_request() was called on a pin it would be the GPIO
> controller driver's responsibility to pinmux it appropriately.
> 
When a GPIO is requested the GPIO layer cannot know what it is
requested for and how the pinmux for the pin function should be
configured (pullups, drive strength, ...). A pin may have multiple
functions depending on what modules are plugged into a baseboard.

Thus the pinctrl binding needs to be with the driver that uses the pin.


Lothar Waßmann
-- 
___________________________________________________________

Ka-Ro electronics GmbH | Pascalstraße 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Geschäftsführer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info at karo-electronics.de
___________________________________________________________