[PATCH 4/8] ARM: imx: add support code for IMX50 based machines

[Rob Herring]

On Fri, Oct 18, 2013 at 1:04 AM,  <gerg at uclinux.org> wrote:
> From: Greg Ungerer <gerg at uclinux.org>
>
> Add machine support code for the Freescale IMX50 SoC.
>
> It is very similar to the Freescale IMX53, it contains many of the same
> periperhal hardware modules, at the same address offsets as the IMX53.
> (Notable exceptions are that the IMX50 contains no CAN bus hardware, less
> GPIO, no VPU, it does contain an Electrophoretic display controller though).
>
> So this support code just uses the IMX53 definitions as they are today.
> We can add the extra IMX50 definitions in the future when required.
>
> Signed-off-by: Greg Ungerer <gerg at uclinux.org>
> ---
>  arch/arm/mach-imx/Makefile     |  1 +
>  arch/arm/mach-imx/mach-imx50.c | 52 ++++++++++++++++++++++++++++++++++++++++++
>  2 files changed, 53 insertions(+)
>  create mode 100644 arch/arm/mach-imx/mach-imx50.c
>
> diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
> index 5383c58..9d94f47 100644
> --- a/arch/arm/mach-imx/Makefile
> +++ b/arch/arm/mach-imx/Makefile
> @@ -110,6 +110,7 @@ obj-$(CONFIG_MACH_EUKREA_CPUIMX51SD) += mach-cpuimx51sd.o
>  obj-$(CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD) += eukrea_mbimxsd51-baseboard.o
>
>  obj-$(CONFIG_MACH_IMX51_DT) += imx51-dt.o
> +obj-$(CONFIG_SOC_IMX50) += mach-imx50.o
>  obj-$(CONFIG_SOC_IMX53) += mach-imx53.o
>
>  obj-$(CONFIG_SOC_VF610) += clk-vf610.o mach-vf610.o
> diff --git a/arch/arm/mach-imx/mach-imx50.c b/arch/arm/mach-imx/mach-imx50.c
> new file mode 100644
> index 0000000..4ac1b91
> --- /dev/null
> +++ b/arch/arm/mach-imx/mach-imx50.c
> @@ -0,0 +1,52 @@
> +/*
> + * Copyright 2013 Greg Ungerer <gerg at uclinux.org>
> + * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
> + * Copyright 2011 Linaro Ltd.
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clkdev.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_platform.h>
> +#include <asm/mach/arch.h>
> +#include <asm/mach/time.h>
> +
> +#include "common.h"
> +#include "mx53.h"
> +
> +static void __init imx50_dt_init(void)
> +{
> +       of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
> +}
> +
> +static const char *imx50_dt_board_compat[] __initdata = {
> +       "fsl,imx50",
> +       NULL
> +};
> +
> +static void __init imx50_timer_init(void)
> +{
> +       mx50_clocks_init_dt();
> +}
> +
> +DT_MACHINE_START(IMX50_DT, "Freescale i.MX50 (Device Tree Support)")
> +       .map_io         = mx53_map_io,
> +       .init_early     = imx53_init_early,
> +       .init_irq       = mx53_init_irq,
> +       .handle_irq     = imx53_handle_irq,
> +       .init_time      = imx50_timer_init,
> +       .init_machine   = imx50_dt_init,
> +       .init_late      = imx53_init_late,
> +       .dt_compat      = imx50_dt_board_compat,
> +       .restart        = mxc_restart,
> +MACHINE_END

This seems like a lot of duplication. It seems like mx53 and mx50
could be combined into a single machine_desc. init_time should not be
needed in 3.13.