[PATCH 5/6] PCI: imx6: Force Gen1 operation

[Marek Vasut]

Hi Richard,

> Hi Marek:
> > -----Original Message-----
> 
> [...]
> 
> > > > ---
> > > > 
> > > >  drivers/pci/host/pci-imx6.c | 13 ++++++++++++-
> > > >  1 file changed, 12 insertions(+), 1 deletion(-)
> > > > 
> > > > diff --git a/drivers/pci/host/pci-imx6.c
> > > > b/drivers/pci/host/pci-imx6.c index ca8c5de..8402e9a 100644
> > > > --- a/drivers/pci/host/pci-imx6.c
> > > > +++ b/drivers/pci/host/pci-imx6.c
> > > > @@ -321,6 +321,7 @@ static void imx6_pcie_host_init(struct pcie_port
> > > > *pp)
> > > > 
> > > >  {
> > > >  
> > > >  	int count = 0;
> > > >  	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
> > > > 
> > > > +	uint32_t tmp;
> > > > 
> > > >  	imx6_pcie_assert_core_reset(pp);
> > > > 
> > > > @@ -330,13 +331,23 @@ static void imx6_pcie_host_init(struct
> > > > pcie_port
> > > > *pp)
> > > > 
> > > >  	dw_pcie_setup_rc(pp);
> > > > 
> > > > +	/*
> > > > +	 * FIXME:
> > > > +	 * Force Gen1 operation. In case the IP block is in Gen2 
operation
> > > > +	 * mode, it does not detect the PCIe switch at all.
> > > > +	 */
> > > > +	tmp = readl(pp->dbi_base + 0x7c);
> > > > +	tmp &= ~0xf;
> > > > +	tmp |= 0x1;
> > > > +	writel(tmp, pp->dbi_base + 0x7c);
> > > > +
> > > 
> > > Since you are forcing RC to work in GEN1, so you will not be able to
> > > connect any device at GEN2 now.
> > 
> > I'd rather prefer to know WHY if the RC is operating in Gen2 mode by
> > default, I cannot see the PCIe switch (Pericom PI7C9X2G303) connected to
> > it. I was unable to figure this out. Tim pointed out this thread [1] ,
> > so it might be related in some way.
> > 
> > [1] https://community.freescale.com/message/316162#316162
> > 
> > I tried switching the PCIe RC to Gen2 operation right after LinkUp by
> > writing this register with 0x2 again and re-issuing the LinkUp check,
> > which passed and the status register reported Gen2 operation, but then
> > the PCIe Intel NIC connected to the downstream port of the Pericom
> > switch still reported Gen1 operation for some reason.
> 
>  [Richard] Is your Inetl NIC GEN1 EP device?

Yes, the i210 is PCIe v2.1 (2.5GT/s) x1 device.

> > > Yes, There are some buggy PCIe devices which works with GEN1 only host.
> > 
> > The pericom one is Gen2 according to it's datasheet.
> 
> [Richard] Yes, it is. Pericom's PI7C9X2G303EL is GEN2 PCIe switch.
> It had been verified on FSL's 3.0.35 releases.

Verified how? What does it mean?

Note that when I followed [1] in this manner:

1) Force GEN1 mode
2) Wait for PHY link up
3) Allow GEN2 mode
4) Start GEN2 speed change
5) Wait for PHY link up

my devices were detected and the link between pericom and mx6 was operating in 
gen2 mode. Thus I suspect we might need to start the port in Gen1 mode and 
switch to Gen2 only after link is up. Does that make sense?

https://community.freescale.com/thread/304284

> > > So better solution should be to initialize RC by default at GEN2 or
> > > highest speed. Further, a parameter say gen_only can be passed from DT
> > > to force GEN1 only mode.
> > > 
> > > What do you say?
> > 
> > I say I'd like to know the root cause of this problem. This Gen2 fix was
> > pulled from one of the myriad variants of the FSL PCIe driver, so
> > apparently this issue happens to other people as well. But why and how
> > to properly fix this so the whole PCIe bus does operate in Gen2 mode, I
> > cannot tell :-(
> 
> [Richard] GEN2 mode had been verified in FSL 3.0.35 kernel releases before.
> I don't know why it can't work in GEN2 mode in the latest kernel.
> BTW, Based on for-next branch of shawn's git reops and applied Merak's
> patch-set, my PI7C9X2G303EL with intel e1000e network card plugged can't
> be detected at all. :(.

I think we're still fighting some issue with resource mappings here. We also 
agreed with Tim that my patches are incomplete. I will send out a new version 
ASAP.