[PATCH 1/3] ahci: exynos: add ahci sata support on Exynos platform

[Tomasz Figa]

Hi,

On Friday 11 of October 2013 15:49:04 Jingoo Han wrote:
> On Tuesday, October 08, 2013 8:45 PM, Yuvaraj Kumar wrote:
> > On Fri, Oct 4, 2013 at 6:03 AM, Jingoo Han <jg1.han at samsung.com> wrote:
> > > On Thursday, October 03, 2013 8:32 PM, Bartlomiej Zolnierkiewicz wrote:
> > >> On Tuesday, October 01, 2013 12:03:01 PM Yuvaraj Kumar C D wrote:
> > >> > Exynos5250 contains one Synopsys AHCI SATA controller.The avalaible
> > >> > ahci_platform driver is not sufficient to handle the AHCI PHY and PHY
> > >> > clock related initialization.
> > >> >
> > >> > This patch adds exynos specific ahci sata driver,contained the exynos
> > >> > specific initialized codes, re-use the generic ahci_platform driver, and
> > >> > keep the generic ahci_platform driver clean as much as possible.
> > >> >
> > >> > This patch depends on the below patch
> > >> >     [1].drivers: phy: add generic PHY framework
> > >> >             by Kishon Vijay Abraham I<kishon at ti.com>
> > >> >
> > >> > Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd at samsung.com>
> > >> > ---
> > >> >  drivers/ata/Kconfig       |    9 ++
> > >> >  drivers/ata/Makefile      |    1 +
> > >> >  drivers/ata/ahci_exynos.c |  226 +++++++++++++++++++++++++++++++++++++++++++++
> > >> >  3 files changed, 236 insertions(+)
> > >> >  create mode 100644 drivers/ata/ahci_exynos.c
> > >> >
> > >
> > >
> > > [.....]
> > >
> > >> > +   priv->phy = devm_phy_get(dev , "sata-phy");
> > >> > +   if (IS_ERR(priv->phy))
> > >> > +           return PTR_ERR(priv->phy);
> > >
> > > [.....]
> > >
> > >> Also please take a look at the following patch:
> > >>
> > >> https://lkml.org/lkml/2013/9/19/173
> > >>
> > >> it adds PHY support to ahci_platform driver, maybe it can be used
> > >> for your needs as well.
> > >
> > > I also agree with Bartlomiej Zolnierkiewicz's opinion.
> > > 'ahci_exynos.c' just calls PHY API, without any additional control
> > > for Exynos AHCI IP.
> > In addition to PHY handling,it also deals with the special clock
> > sclk_sata which is not dealt in ahci_platform.c(certainly exynos
> > specific).
> 
> Handling the special clock 'sclk_sata' is another issue.
> Please, look at that other 'sclk_*'s are handled.
> Also, if possible, please add 'the code handling the special clock'
> to 'ahci_platform.c'.
> 
> > 
> > Morever there is a wrapper driver to handle the platform specific
> > things for the sata.Please refer the  patch[1]
> > [1]ata: ti_sata: Add Texas Instruments SATA Wrapper driver
> > https://lkml.org/lkml/2013/9/19/166
> 
> As Roger Quadros mentioned, 'ti_sata' driver will be dropped.
> 
> > [2]ahci_imx: add ahci sata support on imx platforms
> > 
> 
> 'ahci_imx' is necessary, because 'ahci_imx' controls some
> specific registers.
> 
> However, 'ahci_exynos.c' does not control any registers.
> 
> > I think, if we have platform specific driver like ahci_xxx.c , it
> > would be better to handle the sata PHY in ahci_xxx.c so that we can
> > retain and re-use the ahci_platform.c as it is.
> 
> I think that the platform specific driver like ahci_xxx.c is not
> necessary, because 'ahci_exynos.c' does not control any special
> registers.

My big +1 to all the JIngoo's points above.

Best regards,
Tomasz