[PATCH V4] ARM: OMAP5/DRA7: realtime_counter: Configure CNTFRQ register
Santosh Shilimkar
santosh.shilimkar at ti.com
Wed Oct 9 09:18:09 EDT 2013
On Wednesday 09 October 2013 09:16 AM, Sricharan R wrote:
> On Wednesday 09 October 2013 06:45 PM, Sricharan R wrote:
>> Santosh,
>>
>> On Wednesday 09 October 2013 03:35 AM, Santosh Shilimkar wrote:
>>> On Tuesday 08 October 2013 05:45 PM, Tony Lindgren wrote:
>>>> * Sricharan R <r.sricharan at ti.com> [131003 03:27]:
>>>>> On Wednesday 18 September 2013 09:32 PM, Sricharan R wrote:
>>>>>> --- a/arch/arm/boot/dts/omap5.dtsi
>>>>>> +++ b/arch/arm/boot/dts/omap5.dtsi
>>>>>> @@ -52,7 +52,6 @@
>>>>>> <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
>>>>>> <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
>>>>>> <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
>>>>>> - clock-frequency = <6144000>;
>>>>>> };
>>>>>>
>>>>>> gic: interrupt-controller at 48211000 {
>>>> Can the above be done later on in a separate clean-up patch?
>>>> If so I can drop that part as that removes a dependency to the
>>>> .dts patches queued by Benoit.
>>>>
>>> This can be applied separately.
>>>
>>>
>>>>>> --- a/arch/arm/mach-omap2/omap-smp.c
>>>>>> +++ b/arch/arm/mach-omap2/omap-smp.c
>>>>>> @@ -41,6 +41,8 @@
>>>>>>
>>>>>> u16 pm44xx_errata;
>>>>>>
>>>>>> +extern unsigned long arch_timer_freq;
>>>>>> +
>>>>>> /* SCU base address */
>>>>>> static void __iomem *scu_base;
>>>>>>
>>>> No externs in *.c files please, checkpatch.pl and sparse should warn
>>>> about this.
>>>>
>>>>> Are you planning to pull this patch and the below $subject patch as well? They are
>>>>> acked and tested.
>>>>>
>>>>> ARM: DRA7: realtime_counter: Add ratio registers for 20MHZ sys-clk frequency
>>>>>
>>>>> http://www.spinics.net/lists/linux-omap/msg97281.html
>>>> The 20MHz patch I've applied, just noticed the above things
>>>> when was about to apply this.
>>>>
>>> Now re-looking at the patch, I think this extern stuff can be and
>>> should be avoided. It needs order change though like below. Not
>>> tested but should work.
>>>
>>> diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
>>> index fa74a06..c8d8308 100644
>>> --- a/arch/arm/mach-omap2/timer.c
>>> +++ b/arch/arm/mach-omap2/timer.c
>>> @@ -631,10 +631,9 @@ void __init omap4_local_timer_init(void)
>>> #ifdef CONFIG_SOC_OMAP5
>>> void __init omap5_realtime_timer_init(void)
>>> {
>>> - omap4_sync32k_timer_init();
>>> realtime_counter_init();
>>> -
>>> clocksource_of_init();
>>> + omap4_sync32k_timer_init();
>>> }
>>> #endif /* CONFIG_SOC_OMAP5 */
>>>
>>> Then, the CNTFREQ programming needs to be moved to
>>> realtime_counter_init(). It should be actually part of that
>>> first place instead of timer_init().
>>>
>>> On secondary CPU then a simple asm accessor can
>>> read the CNTFREQ and pass that to SMC.
>> Sorry, I did not quite get you here. You mean an asm accessor to
>> the read the variable that is set in timer.c ?
> Also, is it not ok to move the extern to a .h file instead ?
>
I think you can avoid that variable export with above suggestion
More information about the linux-arm-kernel
mailing list