[PATCH V4] ARM: OMAP5/DRA7: realtime_counter: Configure CNTFRQ register

[Santosh Shilimkar]

On Tuesday 08 October 2013 05:45 PM, Tony Lindgren wrote:
> * Sricharan R <r.sricharan at ti.com> [131003 03:27]:
>> On Wednesday 18 September 2013 09:32 PM, Sricharan R wrote:
>>> --- a/arch/arm/boot/dts/omap5.dtsi
>>> +++ b/arch/arm/boot/dts/omap5.dtsi
>>> @@ -52,7 +52,6 @@
>>>  			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
>>>  			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
>>>  			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
>>> -		clock-frequency = <6144000>;
>>>  	};
>>>  
>>>  	gic: interrupt-controller at 48211000 {
> 
> Can the above be done later on in a separate clean-up patch?
> If so I can drop that part as that removes a dependency to the
> .dts patches queued by Benoit.
>
This can be applied separately. 

 
>>> --- a/arch/arm/mach-omap2/omap-smp.c
>>> +++ b/arch/arm/mach-omap2/omap-smp.c
>>> @@ -41,6 +41,8 @@
>>>  
>>>  u16 pm44xx_errata;
>>>  
>>> +extern unsigned long arch_timer_freq;
>>> +
>>>  /* SCU base address */
>>>  static void __iomem *scu_base;
>>>  
> 
> No externs in *.c files please, checkpatch.pl and sparse should warn
> about this.
> 
>>  Are you planning to pull this patch and the below $subject patch as well? They are
>>  acked and tested.
>>
>>  ARM: DRA7: realtime_counter: Add ratio registers for 20MHZ sys-clk frequency
>>
>>   http://www.spinics.net/lists/linux-omap/msg97281.html
> 
> The 20MHz patch I've applied, just noticed the above things
> when was about to apply this.
> 
Now re-looking at the patch, I think this extern stuff can be and
should be avoided. It needs order change though like below. Not
tested but should work.

diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index fa74a06..c8d8308 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -631,10 +631,9 @@ void __init omap4_local_timer_init(void)
 #ifdef CONFIG_SOC_OMAP5
 void __init omap5_realtime_timer_init(void)
 {
-	omap4_sync32k_timer_init();
 	realtime_counter_init();
-
 	clocksource_of_init();
+	omap4_sync32k_timer_init();
 }
 #endif /* CONFIG_SOC_OMAP5 */
 
Then, the CNTFREQ programming needs to be moved to
realtime_counter_init(). It should be actually part of that
first place instead of timer_init().

On secondary CPU then a simple asm accessor can
read the CNTFREQ and pass that to SMC.

Sricharan,
Can you try above and see if everything works as expected.
If it does, please post an updated patch based on above.

Regards,
santosh