[PATCH V3] ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree

[Tony Lindgren]

* Nishanth Menon <nm at ti.com> [131008 05:08]:
> On 10/07/2013 07:05 PM, Sebastian Reichel wrote:
> > On Mon, Oct 07, 2013 at 03:43:49PM -0500, Nishanth Menon wrote:
> >> diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
> >> index 39c7838..4fe5b9c 100644
> >> --- a/arch/arm/mach-omap2/board-generic.c
> >> +++ b/arch/arm/mach-omap2/board-generic.c
> >> @@ -113,6 +113,7 @@ MACHINE_END
> >>  #ifdef CONFIG_ARCH_OMAP3
> >>  static const char *omap3_boards_compat[] __initdata = {
> >>  	"ti,omap3",
> >> +	"ti,omap343x",
> >             ^^^^
> > You used omap36xx everywhere, so I guess this should be
> > "ti,omap34xx"?
> 
> 3630 has at least two variants:
> http://www.ti.com/product/omap3621
> http://www.ti.com/product/omap3630
> 
> It got further spun off in 37xx family:
> http://www.ti.com/product/dm3730 (DM3730 and DM3725)
> 
> 3430 is no longer in production - but just had a single version (at
> least what I can remember).
> 
> 3530 variant of 3430 on the other hand has a few:
> http://processors.wiki.ti.com/index.php/OMAP3_Overview
> 
> 
> I am ok to change to ti,omap34xx if folks think that is the right
> thing to do. Personally, I might prefer to handle 35xx family slightly
> differently considering deltas.

I've dropped that part as that's not needed for the fix AFAIK.
Here's what I've applied and pushed out to omap-for-v3.12/fixes.

Regards,

Tony

From: Nishanth Menon <nm at ti.com>
Date: Mon, 7 Oct 2013 15:43:49 -0500
Subject: [PATCH] ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree

SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.

With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):

...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...

WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state

So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.

Signed-off-by: Nishanth Menon <nm at ti.com>
[tony at atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony at atomide.com>

diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index 0c514dc..2816bf6 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -11,7 +11,7 @@
 
 / {
 	model = "TI OMAP3 BeagleBoard xM";
-	compatible = "ti,omap3-beagle-xm", "ti,omap3-beagle", "ti,omap3";
+	compatible = "ti,omap3-beagle-xm", "ti,omap36xx", "ti,omap3";
 
 	cpus {
 		cpu at 0 {
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 39c7838..87162e1 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -129,6 +129,24 @@ DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)")
 	.restart	= omap3xxx_restart,
 MACHINE_END
 
+static const char *omap36xx_boards_compat[] __initdata = {
+	"ti,omap36xx",
+	NULL,
+};
+
+DT_MACHINE_START(OMAP36XX_DT, "Generic OMAP36xx (Flattened Device Tree)")
+	.reserve	= omap_reserve,
+	.map_io		= omap3_map_io,
+	.init_early	= omap3630_init_early,
+	.init_irq	= omap_intc_of_init,
+	.handle_irq	= omap3_intc_handle_irq,
+	.init_machine	= omap_generic_init,
+	.init_late	= omap3_init_late,
+	.init_time	= omap3_sync32k_timer_init,
+	.dt_compat	= omap36xx_boards_compat,
+	.restart	= omap3xxx_restart,
+MACHINE_END
+
 static const char *omap3_gp_boards_compat[] __initdata = {
 	"ti,omap3-beagle",
 	"timll,omap3-devkit8000",