[PATCH] DMA: extend documentation to provide more API details

[Russell King - ARM Linux]

On Sat, Oct 05, 2013 at 11:00:45PM +0200, Guennadi Liakhovetski wrote:
> On Sat, 5 Oct 2013, Russell King - ARM Linux wrote:
> 
> > On Sat, Oct 05, 2013 at 07:36:20PM +0200, Guennadi Liakhovetski wrote:
> > > +	A DMA transaction descriptor, returned to the user by one of "prep"
> > > +	methods is considered as belogning to the user until it is submitted
> > > +	to the dmaengine driver for transfer. However, it is recommended, that
> > > +	the dmaengine driver keeps references to prepared descriptors too,
> > > +	because if dmaengine_terminate_all() is called at that time, the driver
> > > +	will have to recycle all allocated descriptors for the respective
> > > +	channel.
> > 
> > No.  That's quite dangerous.  think about what can happen.
> > 
> > Thread 1		Thread 2
> > Driver calls prepare
> > 			dmaengine_terminate_all()
> > 				dmaengine driver frees prepared descriptor
> > driver submits descriptor
> > 
> > You now have a descriptor which has been freed submitted to the DMA engine
> > queue.  This will cause chaos.
> 
> Yes, I understand this. So, it is intentional, that after a *_prep_* a 
> descriptor belongs to the user and - if the user fails - it will simply be 
> leaked. A terminate-all shouldn't recycle them and dmaengine driver 
> unbinding is impossible at that time, as long as the user hasn't released 
> the channel. Ok, I can rework the above just to explain this.

"the user fails" should be very difficult.  One of the requirements here
is that any "user" submits the prepared descriptor as soon as possible
after preparation.  Some DMA engine implementations hold a spinlock
between preparation and submission so this is absolutely necessary.

As Dan Williams explained to me, the reason for the separate submission
step is there to allow the callback information to be set.  So literally
any "user" of this should do this:

	desc = prepare();
	if (!desc)
		goto failed_to_prepare;

	desc->callback = function;
	desc->callback_param = param;
	dmaengine_submit(desc);

There should be very little possiblity of the user failing between those
two calls.

> > > -   On completion of each DMA operation, the next in queue is started and
> > > -   a tasklet triggered. The tasklet will then call the client driver
          ^^^^^^^^^^^^^^^^^^^^
> > > -   completion callback routine for notification, if set.
> > > +   On completion of each DMA operation, the next active transaction in queue is
> > > +   started and the ISR bottom half, e.g. a tasklet or a kernel thread is
> > > +   triggered.
> > 
> > Or a kernel thread?  I don't think that's right.  It's always been
> > specified that the callback will happen from tasklet context.
> 
> Do you see any problems using, say, a threaded interrupt handler, apart 
> from possible performance issues? That seems to be pretty convenient. 
> Otherwise we should really mandate somewhere, that bottom half processing 
> should take place in a tasklet?

The documentation has always stated that callbacks will be made from
tasklet context.  The problem with allowing different contexts from
different drivers is taht spinlocking becomes problematical.  Remember
that we have _bh() variants which lock against tasklets but allow IRQs.

> > > +   The dmaengine driver also has to check the DMA_CTRL_ACK flag by calling
> > > +   async_tx_test_ack() on the transaction. If the function returns true, i.e.
> > > +   if the transaction either has been flagged from the very beginning, or
> > > +   the user has flagged it later, then the transaction descriptor can be
> > > +   recycled immediately by the dmaengine driver.
> > 
> > "has to check" I think is wrong.  This is optional for slave only drivers,
> > because most slave stuff doesn't use the ACK stuff - that's more for the
> > async_tx APIs.
> 
> "most," but some do? E.g. the mx3_camera driver. Ok, that one is very 
> tightly bound to the respective dmaengine driver. But if there are other 
> slave drivers, using that, that can run on different platforms and use 
> various dmaengine drivers?

I'm not aware of any which actually make use of the ack stuff.  Only those
which implement the async_tx must implement this because it gets used for
chaining and dependency stuff.  However, there was a plan to remove this
and replace it with proper refcounting.

> > > If the function returns
> > > +   false, the descriptor cannot be recycled yet and the dmaengine driver has
> > > +   to keep polling the descriptor until it is acknowledged by the user.
> > >  
> > >     Interface:
> > >  	void dma_async_issue_pending(struct dma_chan *chan);
> > > @@ -171,6 +192,14 @@ Further APIs:
> > >     discard data in the DMA FIFO which hasn't been fully transferred.
> > >     No callback functions will be called for any incomplete transfers.
> > >  
> > > +   Note:
> > > +	Transactions, aborted by this call are considered as failed. However,
> > > +	if the user requests their status, using dma_async_is_complete() /
> > > +	dma_async_is_complete(), as described below, one of DMA_IN_PROGRESS and
> > > +	DMA_SUCCESS will be returned. So, drivers are advised not to use those
> > > +	calls on transactions, submitted before a call to
> > > +	dmaengine_terminate_all().
> > 
> > The last sentence doesn't make sense.
> 
> Right, sorry, there is a typo in the second line (to remind: this note is 
> for the dmaengine_terminate_all() function):
> 
> +   Note:
> +	Transactions, aborted by this call are considered as failed. However,
> +	if the user requests their status, using dma_async_is_tx_complete() /
> +	dma_async_is_complete(), as described below, one of DMA_IN_PROGRESS and
> +	DMA_SUCCESS will be returned. So, drivers are advised not to use those
> +	calls on transactions, submitted before a call to
> +	dmaengine_terminate_all().
> 
> What I was trying to say, is that if you submit transactions, then 
> terminate them, then try to retrieve their status using 
> dma_async_is_tx_complete() / dma_async_is_complete(), this won't produce 
> the expected DMA_ERROR result, instead, one of DMA_IN_PROGRESS and 
> DMA_SUCCESS will be returned, unless the driver implements some 
> sophisticated .device_tx_status() method.

Remember that dmaengine_terminate_all() is targetted to a specific
channel - it terminates all submitted transactions on that channel
and stops any in-process transaction.  It doesn't affect any other
channel on the controller.

In the case of slave DMA users, you have to "own" the channel.  This
means it's up to the user to sort out what happens should _they_ call
dmaengine_terminate_all() on it.

For non-slave DMA users, I don't believe that terminating transactions
is permitted - they're expected to complete.