[PATCH v3 05/10] ARM: dts: omap3-beagle: Use reset-gpios for hsusb2_reset

[Benoit Cousson]

On 03/10/2013 15:58, Roger Quadros wrote:
> Hi Benoit,
>
> On 10/03/2013 04:44 PM, Benoit Cousson wrote:
>> On 03/10/2013 14:05, Benoit Cousson wrote:
>>> Hi Roger,
>>>
>>> Yes, I will. I've been waiting for these ones for so long :-)
>>
>> In fact it does not apply correctly on my for_3.13/dts branch :-(
>>
>> error: arch/arm/boot/dts/omap3-beagle.dts: patch does not apply
>> Patch failed at 0004 ARM: dts: omap3-beagle: Make USB host pin naming consistent
>>
>> Could you rebase it?
>
> Looks like it was already applied before. Could you please skip that and use the rest?
> I've checked that the remaining patches apply fine on top of your for_3.13/dts
> branch.

Indeed, it was already there :-)

Sorry for the noise.

Benoit

>
> cheers,
> -roger
>
>>>
>>> On 03/10/2013 12:34, Roger Quadros wrote:
>>>> Hi Benoit,
>>>>
>>>> Could you please take the device tree related patches [5 to 10] in
>>>> this series?
>>>> Thanks.
>>>>
>>>> cheers,
>>>> -roger
>>>>
>>>> On 09/24/2013 11:53 AM, Roger Quadros wrote:
>>>>> We no longer need to model the RESET line as a regulator since
>>>>> the USB phy-nop driver accepts "reset-gpios" property.
>>>>>
>>>>> Signed-off-by: Roger Quadros <rogerq at ti.com>
>>>>> ---
>>>>>    arch/arm/boot/dts/omap3-beagle.dts |   13 +------------
>>>>>    1 files changed, 1 insertions(+), 12 deletions(-)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/omap3-beagle.dts
>>>>> b/arch/arm/boot/dts/omap3-beagle.dts
>>>>> index dfd8310..71bde47 100644
>>>>> --- a/arch/arm/boot/dts/omap3-beagle.dts
>>>>> +++ b/arch/arm/boot/dts/omap3-beagle.dts
>>>>> @@ -44,17 +44,6 @@
>>>>>            };
>>>>>        };
>>>>>
>>>>> -    /* HS USB Port 2 RESET */
>>>>> -    hsusb2_reset: hsusb2_reset_reg {
>>>>> -        compatible = "regulator-fixed";
>>>>> -        regulator-name = "hsusb2_reset";
>>>>> -        regulator-min-microvolt = <3300000>;
>>>>> -        regulator-max-microvolt = <3300000>;
>>>>> -        gpio = <&gpio5 19 0>;    /* gpio_147 */
>>>>> -        startup-delay-us = <70000>;
>>>>> -        enable-active-high;
>>>>> -    };
>>>>> -
>>>>>        /* HS USB Port 2 Power */
>>>>>        hsusb2_power: hsusb2_power_reg {
>>>>>            compatible = "regulator-fixed";
>>>>> @@ -68,7 +57,7 @@
>>>>>        /* HS USB Host PHY on PORT 2 */
>>>>>        hsusb2_phy: hsusb2_phy {
>>>>>            compatible = "usb-nop-xceiv";
>>>>> -        reset-supply = <&hsusb2_reset>;
>>>>> +        reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;    /* gpio_147 */
>>>>>            vcc-supply = <&hsusb2_power>;
>>>>>        };
>>>>>
>>>>>
>>>>
>>>
>>
>