[PATCH v4] ARM: vexpress/TC2: Implement MCPM power_down_finish()
Dave Martin
Dave.Martin at arm.com
Wed Oct 2 10:45:55 EDT 2013
This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.
The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:
* mcpm_cpu_power_down() must be pending for the CPU, so that we
don't get confused by false STANDBYWFI positives arising from
CPUidle. This is detected by waiting for the tc2_pm use count
for the target CPU to reach 0.
* Either the SPC must report that the CPU has asserted
STANDBYWFI, or the TC2 tile's reset control logic must be
holding the CPU in reset.
Just checking for STANDBYWFI is not sufficient, because this
signal is not latched when the the cluster is clamped off and
powered down: the relevant status bits just drop to zero. This
means that STANDBYWFI status cannot be used for reliable
detection of the last CPU in a cluster reaching WFI.
This patch is required in order for kexec to work with MCPM on TC2.
Signed-off-by: Dave Martin <Dave.Martin at arm.com>
---
Changes since v3:
* Fix the location of the RESET_A7_NCORERESET() macro so that the
A7_NCORERESET bits in the reset control register start at bit 19,
not bit 19.
It looks like I misread the TRM on the first pass :/
Bits 19-21 are the A7_ETMRESET bits. In practice the SPC sets/
clears all these bits simultaneously anyway, so the code still
worked regardless, but future versions of the SPC firmware could
behave differently.
The A15 NCORERESET bits do indeed start at bit 2, so that doesn't
need fixing.
* Acks dropped -- Nico, if you can take a quick look to confirm I've
not gone insane, that would be appreciated, thanks.
* The generic MCPM patches from previous postings are in Russell's
patch system pending his approval, so I've dropped them from this
repost.
arch/arm/mach-vexpress/spc.c | 39 +++++++++++++++++++++++
arch/arm/mach-vexpress/spc.h | 1 +
arch/arm/mach-vexpress/tc2_pm.c | 66 ++++++++++++++++++++++++++++++++++++---
3 files changed, 101 insertions(+), 5 deletions(-)
diff --git a/arch/arm/mach-vexpress/spc.c b/arch/arm/mach-vexpress/spc.c
index eefb029..6f6ac56 100644
--- a/arch/arm/mach-vexpress/spc.c
+++ b/arch/arm/mach-vexpress/spc.c
@@ -35,6 +35,10 @@
/* SPC per-CPU mailboxes */
#define A15_BX_ADDR0 0x68
#define A7_BX_ADDR0 0x78
+/* SPC CPU/cluster reset statue */
+#define STANDBYWFI_STAT 0x3c
+#define STANDBYWFI_STAT_A15_CPU_MASK(cpu) (1 << (cpu))
+#define STANDBYWFI_STAT_A7_CPU_MASK(cpu) (1 << (3 + (cpu)))
/* wake-up interrupt masks */
#define GBL_WAKEUP_INT_MSK (0x3 << 10)
@@ -157,6 +161,41 @@ void ve_spc_powerdown(u32 cluster, bool enable)
writel_relaxed(enable, info->baseaddr + pwdrn_reg);
}
+static u32 standbywfi_cpu_mask(u32 cpu, u32 cluster)
+{
+ return cluster_is_a15(cluster) ?
+ STANDBYWFI_STAT_A15_CPU_MASK(cpu)
+ : STANDBYWFI_STAT_A7_CPU_MASK(cpu);
+}
+
+/**
+ * ve_spc_cpu_in_wfi(u32 cpu, u32 cluster)
+ *
+ * @cpu: mpidr[7:0] bitfield describing CPU affinity level within cluster
+ * @cluster: mpidr[15:8] bitfield describing cluster affinity level
+ *
+ * @return: non-zero if and only if the specified CPU is in WFI
+ *
+ * Take care when interpreting the result of this function: a CPU might
+ * be in WFI temporarily due to idle, and is not necessarily safely
+ * parked.
+ */
+int ve_spc_cpu_in_wfi(u32 cpu, u32 cluster)
+{
+ int ret;
+ u32 mask = standbywfi_cpu_mask(cpu, cluster);
+
+ if (cluster >= MAX_CLUSTERS)
+ return 1;
+
+ ret = readl_relaxed(info->baseaddr + STANDBYWFI_STAT);
+
+ pr_debug("%s: PCFGREG[0x%X] = 0x%08X, mask = 0x%X\n",
+ __func__, STANDBYWFI_STAT, ret, mask);
+
+ return ret & mask;
+}
+
int __init ve_spc_init(void __iomem *baseaddr, u32 a15_clusid)
{
info = kzalloc(sizeof(*info), GFP_KERNEL);
diff --git a/arch/arm/mach-vexpress/spc.h b/arch/arm/mach-vexpress/spc.h
index 5f7e4a4..edb1b06 100644
--- a/arch/arm/mach-vexpress/spc.h
+++ b/arch/arm/mach-vexpress/spc.h
@@ -20,5 +20,6 @@ void ve_spc_global_wakeup_irq(bool set);
void ve_spc_cpu_wakeup_irq(u32 cluster, u32 cpu, bool set);
void ve_spc_set_resume_addr(u32 cluster, u32 cpu, u32 addr);
void ve_spc_powerdown(u32 cluster, bool enable);
+int ve_spc_cpu_in_wfi(u32 cpu, u32 cluster);
#endif
diff --git a/arch/arm/mach-vexpress/tc2_pm.c b/arch/arm/mach-vexpress/tc2_pm.c
index e6eb481..867eed8 100644
--- a/arch/arm/mach-vexpress/tc2_pm.c
+++ b/arch/arm/mach-vexpress/tc2_pm.c
@@ -12,6 +12,7 @@
* published by the Free Software Foundation.
*/
+#include <linux/delay.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/kernel.h>
@@ -31,11 +32,17 @@
#include "spc.h"
/* SCC conf registers */
+#define RESET_CTRL 0x018
+#define RESET_A15_NCORERESET(cpu) (1 << (2 + (cpu)))
+#define RESET_A7_NCORERESET(cpu) (1 << (16 + (cpu)))
+
#define A15_CONF 0x400
#define A7_CONF 0x500
#define SYS_INFO 0x700
#define SPC_BASE 0xb00
+static void __iomem *scc;
+
/*
* We can't use regular spinlocks. In the switcher case, it is possible
* for an outbound CPU to call power_down() after its inbound counterpart
@@ -233,6 +240,55 @@ static void tc2_pm_power_down(void)
tc2_pm_down(0);
}
+static int tc2_core_in_reset(unsigned int cpu, unsigned int cluster)
+{
+ u32 mask = cluster ?
+ RESET_A7_NCORERESET(cpu)
+ : RESET_A15_NCORERESET(cpu);
+
+ return !(readl_relaxed(scc + RESET_CTRL) & mask);
+}
+
+#define POLL_MSEC 10
+#define TIMEOUT_MSEC 1000
+
+static int tc2_pm_power_down_finish(unsigned int cpu, unsigned int cluster)
+{
+ unsigned tries;
+
+ pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
+ BUG_ON(cluster >= TC2_CLUSTERS || cpu >= TC2_MAX_CPUS_PER_CLUSTER);
+
+ for (tries = 0; tries < TIMEOUT_MSEC / POLL_MSEC; ++tries) {
+ /*
+ * Only examine the hardware state if the target CPU has
+ * caught up at least as far as tc2_pm_down():
+ */
+ if (ACCESS_ONCE(tc2_pm_use_count[cpu][cluster]) == 0) {
+ pr_debug("%s(cpu=%u, cluster=%u): RESET_CTRL = 0x%08X\n",
+ __func__, cpu, cluster,
+ readl_relaxed(scc + RESET_CTRL));
+
+ /*
+ * We need the CPU to reach WFI, but the power
+ * controller may put the cluster in reset and
+ * power it off as soon as that happens, before
+ * we have a chance to see STANDBYWFI.
+ *
+ * So we need to check for both conditions:
+ */
+ if (tc2_core_in_reset(cpu, cluster) ||
+ ve_spc_cpu_in_wfi(cpu, cluster))
+ return 0; /* success: the CPU is halted */
+ }
+
+ /* Otherwise, wait and retry: */
+ msleep(POLL_MSEC);
+ }
+
+ return -ETIMEDOUT; /* timeout */
+}
+
static void tc2_pm_suspend(u64 residency)
{
unsigned int mpidr, cpu, cluster;
@@ -275,10 +331,11 @@ static void tc2_pm_powered_up(void)
}
static const struct mcpm_platform_ops tc2_pm_power_ops = {
- .power_up = tc2_pm_power_up,
- .power_down = tc2_pm_power_down,
- .suspend = tc2_pm_suspend,
- .powered_up = tc2_pm_powered_up,
+ .power_up = tc2_pm_power_up,
+ .power_down = tc2_pm_power_down,
+ .power_down_finish = tc2_pm_power_down_finish,
+ .suspend = tc2_pm_suspend,
+ .powered_up = tc2_pm_powered_up,
};
static bool __init tc2_pm_usage_count_init(void)
@@ -312,7 +369,6 @@ static void __naked tc2_pm_power_up_setup(unsigned int affinity_level)
static int __init tc2_pm_init(void)
{
int ret;
- void __iomem *scc;
u32 a15_cluster_id, a7_cluster_id, sys_info;
struct device_node *np;
--
1.7.9.5
More information about the linux-arm-kernel
mailing list