[RFC] ARM: OMAP2+: omap_device: add pinctrl handling

[Grygorii Strashko]

Picture format fixed. Sorry for that.

On 06/26/2013 04:20 PM, Grygorii Strashko wrote:
> Hi All,
>
> On 06/25/2013 09:58 AM, Tony Lindgren wrote:
>> * Linus Walleij <linus.walleij at linaro.org> [130624 05:13]:
>>> On Fri, Jun 21, 2013 at 5:03 PM, Grygorii Strashko
>>> <grygorii.strashko at ti.com> wrote:
>>>
>>>> Hence, add pinctrl handling in omap_device core:
>>>> 1) on PM runtime resume
>>>> - switch pinctrl state to "default" (todo: "active")
>>>> 2) on PM runtime suspend
>>>> - switch pinctrl state to "idle"
>>>> 3) during system wide suspend
>>>> - switch pinctrl state to "sleep" or "idle" if omap_device core
>>>> disables device
>>>> - switch pinctrl state to "sleep" if device is disabled already
>> Do you need a separate setting for "idle" and "sleep", or are
>> they the same?
>>
>>>> 4) during system wide resume
>>>> - switch pinctrl state to "default" (todo: "active") if omap_device
>>>> core has
>>>>    disabled  device during suspend
>>>> - switch pinctrl state to "idle" if device was already disabled
>>>> before suspend
>>> I don't understand step 4.
>>>
>>> I get the creeps about whether the system is runtime suspended
>>> or runtime resumed when we come to resume proper, so I need
>>> Kevin to have a look at this.
>>>
>>> Apart from that it looks good.
>>>
>>> Stephen and Tony are trying to figure out the details of whether
>>> "active"
>>> is necessary or not in a related thread I think.
> Thanks for your comments.
>
> I've prepared diagram to illustrate how does this work:
>                                          +
>                                          |
>                                          |  .probe()
>                                          |
>                                    +-----v--------+
>                                    |              |
>                                    |  default     |
>                                    |              |
>                                    +----+--+------+
>                                         |  |
>                         pm_runtime_get()|  | pm_runtime_put()
>                        +----------------+  +------------+
>                        |                                |
>                 +------v------+ pm_runtime_put()+-------v-----+
>                 |             +----------------->             |
>     +----------->  Active     |pm_runtime_get() |   Idle      <----------+
>     |           |             <-----------------+             |          |
>     |           +-------+-----+                 +-------+-----+          |
>     |                   |.suspend_noirq()               |.suspend_noirq()|
>     |                   |                               |                |
>     |                   |                               |                |
>     |                   |                               |                |
>     |                   |                               |                |
>     |           +-------v-----+                 +-------v-----+          |
>     |           |             |                 |             |          |
>     +-----------+  Sleep      ------+           |  Sleep      +----------+
> .resume_noirq() |             |     |           |             |.resume_noirq()
>                 +-------|-----+     |           +-------------+
>                         |  Idle     |
>                         +-----------+
>
> The "Sleep" pinctrl state is optional - if "sleep" state isn't defined
> then "Idle" pinctrl state will be used during suspend.
>
> As per above pinctrl state transition diagram - I think, that:
> - if "idle" or "sleep" states are defined then "active" state have to be
> defined too.
> So, pinctrl core should detect such situation and generate a warning.
>
>  From my point of view, we should have "active" state - it would allow
> to avoid additional
> runtime overhead and handle properly the case when drivers are used as
> loadable modules.
> In this case, after boot, device's pinctrl registers can have HW default
> values (after reset) or
> can be configured to some safe (off) state from board file (board's
> "default" configuration).
> Driver module will activate its PINs when loaded and need to restore
> safe (off) PINs state when
> unloaded.
> As result, it seems, we should have "off" state which can be used when
> driver's module is removed.
>
> So, final list of default pnctrl states may be defined as "default",
> "active", "idle", "sleep", "off":
> - "active", "idle", "sleep": will be handled by omap_device core
> - "default", "off": will be handled by driver itself (or Device core).
>
>
>
>> Yes we should have that sorted out over next few weeks, so let's
>> just wait a little while on all these dynamic remuxing patches
>> to avoid churn.
>>
>> Regards,
>>
>> Tony
>
> Regards,
> - grygorii
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html