[PATCH] pinctrl: establish pull-up/pull-down terminology

James Hogan james.hogan at imgtec.com
Thu Jun 20 08:38:22 EDT 2013


On 19/06/13 23:03, Stephen Warren wrote:
> On 06/16/2013 04:45 AM, Linus Walleij wrote:
>> From: Linus Walleij <linus.walleij at linaro.org>
>>
>> It is counter-intuitive to have "0" mean disable in a boolean
>> manner for electronic properties of pins such as pull-up and
>> pull-down. Therefore, define that a pull-up/pull-down argument
>> of 0 to such a generic option means that the pin is
>> short-circuited to VDD or GROUND. Pull disablement shall be
>> done using PIN_CONFIG_BIAS_DISABLE.
>>
>> Cc: Heiko St�bner <heiko at sntech.de>
>> Cc: James Hogan <james.hogan at imgtec.com>
>> Cc: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
>> Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
>> ---
>>  include/linux/pinctrl/pinconf-generic.h | 13 +++++++------
>>  1 file changed, 7 insertions(+), 6 deletions(-)
>>
>> diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
>> index d414a77..67780f5 100644
>> --- a/include/linux/pinctrl/pinconf-generic.h
>> +++ b/include/linux/pinctrl/pinconf-generic.h
>> @@ -36,14 +36,15 @@
>>   *	tristate. The argument is ignored.
>>   * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
>>   *	impedance to VDD). If the argument is != 0 pull-up is enabled,
>> - *	if it is 0, pull-up is disabled.
>> + *	if it is 0, pull-up it total, i.e. the pin is connected to VDD.
>>   * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
>>   *	impedance to GROUND). If the argument is != 0 pull-down is enabled,
>> - *	if it is 0, pull-down is disabled.
>> + *	if it is 0, pull-down is total, i.e. the pin is connected to GROUND.
>>   * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based
>>   *	on embedded knowledge of the controller, like current mux function.
>> - *	If the argument is != 0 pull up/down is enabled, if it is 0,
>> - *	the pull is disabled.
>> + *	If the argument is != 0 pull up/down is enabled, if it is 0, the
>> + *	configuration is ignored. The proper way to disable it is to use
>> + *	@PIN_CONFIG_BIAS_DISABLE.
> 
> Why treat PULL_UP/PULL_DOWN differently from PULL_PIN_DEFAULT?
> PULL_PIN_DEFAULT is logically simply a macro that selects PULL_UP/DOWN
> based on what's "normal" for the pin's expected usage, so surely the
> value associated with that option should behave identically?

I'm not familiar with hardware that does this so I could be way wrong
here, but presumably if there's a default up/down, there's probably a
default resistance too. Does it really make sense to say
"pull up or down depending on whatever the pin is intended for... but
whichever it is must be XXX Ohm"?
If you know the resistance you want, you surely already know whether you
want it pull up or down with that resistence.

Cheers
James




More information about the linux-arm-kernel mailing list